Recommended Floor Drain Detail, Assembly | Cleveland Range KEL-40-T

RECOMMENDED FLOOR DRAIN DETAIL

RECOMMENDED
FLOOR	FLOOR SLOPE
DRAIN	FLOOR SLOPE
	1" IN 4'
4" MINIMUM,	PIPE DRAIN
6" RECOMMENDED	RECOMMENDED
	MINIMUM VALVE
	SIZE PLUS 1"
ASSEMBLY

FLANGED

FOOT (5" DIA)

(3) 7/16" DIA.

3 1/8" HOLES

Flanged Foot Detail

Position the kettle in it's permanent location, and level the kettle by turning the adjustable flanged feet. Once positioned and leveled, permanently secure the kettle's flanged feet to the floor using 5/16" lag bolts and floor anchors (supplied by the installer). There are three bolts required to secure each of the flanged feet.

WIRE CONNECTION

Install in accordance with local codes and/or the National Electric Code ANSI/NFPA No. 70-1990 (USA) or the Canadian Electric Code CSA Standard C22.1 (Canada). A separate fused disconnect switch must be supplied and installed. The kettle must be electrically grounded by the installer.

The electrical supply must match the power requirements specified on the kettle's rating plate. The copper wiring must be adequate to carry the required current at the rated voltage.

Note: Maximum voltage for LVD (low voltage directive for Europe) to be 440 volts for CE marked appliances.

THREE

BLACK

BLUE

RED

SINGLE

BLACK

BLUE

RED

PHASE

RED

YELLOW

BLACK

The kettle is wired for 3-phase operation at the factory. For single phase operation, rewire the terminal block to that shown in the above diagram.

Note: Ensure main power is turned off before connecting wires.

Stationary Models

Remove the screws securing the dome-shaped service cover underneath the kettle and remove the cover. A wiring diagram is affixed to the inside of cover. Fasten permanent copper wiring to the three-connection terminal block, Be sure to connect ground wire to the separate ground terminal connector (ground lug). Slide the cover's slot over the wiring and secure the cover to kettle with the screws.

Tilting Models

First remove the handwheel by loosening the allen screw. Then remove the two screws at the front and rear of the console cover and remove the cover. A wiring diagram is affixed to the underside of the console cover. Feed permanent copper wiring through the cut-out in the bottom of the console, and fasten to the three-connection terminal block. Be sure to connect the ground terminal connector (ground lug). Replace the console cover and handwheel.

WATER

The sealed jacket of the electric kettle is precharged with the correct amount of a water- based formula, and therefore, no water connection is required to the kettle jacket. The kettle can be equipped with optional hot and cold water taps, the taps require 1/2" copper tubing as supply lines.

KEL-60, KEL-60-TSH, KEL-60-T, KEL-25, KEL-25-T specifications

Cleveland Range is renowned for its high-quality cooking equipment, particularly its lineup of electric kettles designed for commercial kitchens. Among its impressive array, the KEL-30, KEL-60-SH, KEL-100-T, KEL-80-T, and KEL-40-T models stand out for their unique features and innovative technologies.

The KEL-30 is a compact yet powerful kettle, ideal for operations that have limited space but still require efficiency. With a 30-gallon capacity, it is perfect for cooking soups, sauces, and stews. Its advanced heating technology ensures rapid boil times, reducing wait times and increasing productivity. The kettle's low-profile design allows for easy access, making it user-friendly.

Next in line is the KEL-60-SH, which boasts a 60-gallon capacity. This model is equipped with a steam jacket, enhancing heat distribution and minimizing the risk of scorching. The KEL-60-SH is especially equipped to handle larger quantities, making it suitable for institutions like schools or large restaurants. Its precise temperature controls enable chefs to maintain consistent cooking results.

The KEL-100-T represents the top end of Cleveland's kettle range with an impressive 100-gallon capacity. Designed for high-volume operations, this kettle integrates cutting-edge technology to optimize cooking performance. Its tilting feature simplifies the pouring process, while the robust stainless steel construction ensures durability and easy cleaning.

The KEL-80-T offers a balance in size and functionality, featuring an 80-gallon capacity. With similar tilting mechanisms as its larger counterpart, it is designed for versatility, allowing chefs to prepare a variety of dishes efficiently.

Lastly, the KEL-40-T, with a 40-gallon capacity, caters to kitchens that require flexibility without sacrificing volume. This model is particularly popular in mid-sized establishments that aim to serve a diverse menu.

Across the range, each kettle features a user-friendly control panel, enabling chefs to set precise cooking temperatures and timers. Safety is also a priority, with features like pressure relief valves and cool-touch handles to prevent burns.

In conclusion, Cleveland Range's KEL-30, KEL-60-SH, KEL-100-T, KEL-80-T, and KEL-40-T models collectively represent the pinnacle of commercial kettle technology. Each unit is tailored to meet different operational needs while ensuring consistent performance, making them invaluable assets in any bustling kitchen.