Whirlpool W10196160B To Convert Surface Burners, To Convert Oven Bake Burner

Page 13

To Convert Surface Burners

1.Remove burner cap.

2.Using a Phillips screwdriver, remove the burner base.

NOTE: Reinstall one of the screws through the range cooktop to hold the orifice spud holder in place while removing and replacing the orifice spuds.

C

A

D

B

A. Igniter electrode

B. Gas tube opening

C. Burner cap

D. Burner base

3.Apply masking tape to the end of a ⁵⁄₁₆" nut driver to help hold the gas orifice spud in the nut driver while changing it. Press nut driver down onto the gas orifice spud and remove by turning it counterclockwise and lifting out. Set gas orifice spud aside.

C

A

D

B

A.Orifice spud

B.Orifice spud holder

C.Screw

D.Spark electrode

4.Remove the cardboard orifice spud holder located on the back of the range near the gas inlet. Gas orifice spuds are stamped with a number, marked with 1 color dot, and have a groove in the hex area. Replace the Natural gas orifice spud with the correct LP gas orifice spud.

A

A. Groove

Refer to the following chart for correct LP gas orifice spud placement.

LP Gas Orifice Spud Chart for Surface Burners

Burner Rating

Color

Size

ID Number

14,000 BTU

Yellow/Orange

1.07 mm

L107

11,000 BTU

Yellow/Brown

0.99 mm

L99

8,000 BTU

Yellow/Black

0.85 mm

L85

5,000 BTU

Yellow/White

0.70 mm

L70

 

 

 

 

NOTE: Refer to the Model Number and Serial Number Plate located behind the left side of the storage or warming drawer for proper sizing of spuds for each burner location.

5.Place Natural gas orifice spuds in the cardboard orifice spud holder.

6.Replace the burner base using both screw.

7.Replace burner cap.

8.Repeat steps 1-7 for the remaining burners.

To Convert Oven Bake Burner

1.Remove oven racks.

2.Use a ½" combination wrench to turn the orifice hood down snug onto pin (about 2 to 2½ turns).

IMPORTANT: Do not overtighten.

The oven bake burner flame cannot be properly adjusted if this conversion is not made. See “Adjust Oven Bake Burner Flame” in the “Electronic Ignition System” section.

A

B

A

A

A. Orifice hood

B. Pin

To Convert Oven Broil Burner

Use a ½" combination wrench to turn the orifice hood down snug onto the pin (about 2 to 2½ turns).

IMPORTANT: Do not overtighten.

The oven broil burner flame cannot be properly adjusted if this conversion is not made. See “Adjust Oven Broil Burner Flame” in the “Electronic Ignition System” section.

A

B

A. Lock screw

B. Orifice hood

13

Image 13
Contents Autoportantes DE 30 76,2 CM Instructions D’INSTALLATION DES Cuisinières À GAZYour safety and the safety of others are very important Range SafetyTools and Parts Installation RequirementsLocation Requirements Cabinet Dimensions Product DimensionsType of Gas Electrical RequirementsGas Supply Line Natural gasGas Supply Pressure Testing Installation InstructionsUnpack Range Gas Pressure RegulatorOn Ranges Equipped with Storage Drawers Install Anti-Tip BracketOn Ranges Equipped with Warming Drawers Typical rigid pipe connection Make Gas ConnectionComplete Connection Typical flexible connectionLevel Range Verify Anti-Tip Bracket LocationElectronic Ignition System Check Operation of Oven Bake Burner Adjust Oven Bake Burner Flame if neededReplace Oven Racks Storage or Warming Drawer Complete InstallationLP Gas Conversion GAS ConversionsTo Convert Gas Pressure Regulator To Convert Oven Bake Burner To Convert Surface BurnersTo Convert Oven Broil Burner Natural Gas Conversion Complete InstallationStamped number Votre sécurité et celle des autres est très importante Sécurité DE LA CuisinièreEmplacement d’installation Exigences D’INSTALLATIONOutillage et pièces Dimensions du placard Dimensions de lappareilSpécifications de l’alimentation en gaz Spécifications électriquesType de gaz Gaz naturelDétendeur de gaz Canalisation de gazDébit thermique des brûleurs Tests de pressurisation de la canalisation de gazInstallation de la bride antibasculement Instructions DinstallationDéballage de la cuisinière Sur les cuisinières équipées d’un tiroir réchaudRaccordement typique à une canalisation rigide Raccordement à la canalisation de gazRaccordement typique par raccord flexible Vérification de lemplacement de la bride AntibasculementCompléter le raccordement Système dallumage électronique Mise à niveau de la cuisinièrePour ôter le répartiteur de flammes Contrôle du fonctionnement du brûleur du grilUtilisation dun miroir Sil est nécessaire de régler la taille des flammesSi vous avez besoin dassistance ou de service Achever l’installationConversions Pour Changement DE GAZ Conversion de Gaz naturel à PropaneConversion des brûleurs de la table de cuisson Conversion du détendeurConversion du brûleur du four Achever linstallationConversion du brûleur du gril Conversion de Propane à Gaz naturel Marquage didentification Page W10196160B