Cornelius Cold Beverage Dispenser manual Total Flex Manifold Insulation Removed

Page 10

IntelliCarb Training Manual

Ice Drink Model ED150/175/300 Coldplate Cover

Ice Drink Model ED200/250 Coldplate Cover

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Liquid Level Probe

CO2

Check Valve with Ground Stud

In-line CO2 Check Valve

Probe

Ground Plate/Stud

 

 

FIGURE 9

FIGURE 10

 

3.Total Flex System for Ice Drink Models ED150/175/200/250/300

Total Flex Manifold (Insulation Removed)

Water Line

 

 

 

 

 

Plugs

Retainer Clip

Manifold Block

FIGURE 11

Total Flex is a system of water manifold blocks located at the front of the cold plate, adjacent to the cold plate inlets, for easy switch over of carbonated / non-carbonated beverage drinks. The right hand mani- fold block is for the beverage valves located to the right side of the ice chute, and the left block is for the left bank of valves. Each beverage valve on the dispenser can be set up for either carbonated or non-car- bonated drinks. Refer to the unit’s plumbing diagram for the factory carbonated / non-carbonated valve locations. The procedure for switching carbonated / non-carbonated water lines on a beverage valve is as follows:

A.Shut off the water supply to the dispenser. Depressurize and drain both the carbonated and non- carbonated water circuits.

B.Remove the retainer clip (2 screws) from the manifold block. Switch the plug and water line fitting to their respective carbonated / non-carbonated outlet locations on the block.

C.Replace the retainer clip. Turn on the water supply and energize the “switched” valve(s). Check for water leaks.

4.Important: Route the dispenser’s drain line to an open drain with the end of the tube above the flood level of the drain. The drain line must pitch downward and contain no “traps”.

5.Connect both the carbonator pump and motor unit and the dispenser to a grounded electrical sup- ply outlet.

Publication Number: TP01071

- 6 -

© 2004, IMI Cornelius Inc.

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Intellicarb Intellicarb Training Manual Table of Contents Electrical Section Theory of Operation IntroductionUnit Description DescriptionRequirements SpecificationsDimensions CO2 Operating Pressure Delivery Inspection and UnpackingInstallation LEG OptionCornelius Intellicarb Carbonator Assembly Carbonator Time Out Reset SwitchDrains Carbonator Relief Valve Locations Ice Drink Model ED175BCH Lower Front Panel RemovedTotal Flex Manifold Insulation Removed Check list for proper finished drink carbonation Mechanical Section AdjustmentGate Restrictor Plate ICE Diverter KIT To Remove Agitators For Cleaning 300 shown Removal and Replacement of AgitatorsWater Dimensions & CapacitiesPOST-MIX Valve Section SET-UP InstructionsSame Volume Syrup/Water Flows From Orifices Lower Fluid Syrup/Concentrate Adjusting Flow RatesCalculating Flow Rates Setting Ratios Shurflo Shurflow OverviewShurflow Installation START-UP ProcedureTypical Installation PlumbingPlumbing Layout Plumbing LayoutFlow Diagram Flow Diagram 1XX SIX Flavor Model1xx Six Flavor Model Eight Flavor Models FlowFlow Diagram 2XX Eight Flavor Models 2xx Eight Flavor ModelsFlow Diagram 2XX TEN Flavor Models Flow Diagram 2xx Ten Flavor ModelsFlow Flow Diagram 300 Twelve FLavor Models Twelve Flavor ModelsElectrical Section Electrical Box 1xx Single TransformerCarbonator Wiring Diagram Reset Connections1xx POW ER B Efore Servicing UnitSchematic SchematicWiring Diagram 2XX 120V Model 2xx 120V ModelWiring Diagram 2xx 220/240V ModelsWiring Diagram 2XX 220/240V Models Wiring Diagram 2xx 220/240V Models220/240V Models 300 2004, IMI Cornelius IncSchematic 300 120V Models Schematic 300 120V ModelsSchematic 300 220/240V Models Shurflow Troubleshooting TroubleshootingPumping Capability Pumps in Series for Long Distances Pump Sanitizing / WinterizingPump Troubleshooting Operated without fluid for excessive period. Dry runProbable Cause Dispenser TroubleshootingTrouble RemedyValve Troubleshooting Excess FoamOff Taste Off TasteValve Stuck Open Valve Stuck OpenNo Product No ProductSolid State Carbonator Level Control Carbonator TroubleshootingTest Solid State Level Control IMI Cornelius Inc

Cold Beverage Dispenser specifications

The Cornelius Cold Beverage Dispenser is an advanced piece of equipment devised to meet the increasing demand for customizable cold beverages in both commercial and residential environments. Recognized for its reliability and innovation, this dispenser is designed to serve a variety of beverages, including carbonated soft drinks, iced teas, and flavored water, making it a versatile addition for any establishment such as restaurants, cafes, and events.

One of the standout features of the Cornelius Cold Beverage Dispenser is its ability to dispense multiple beverages simultaneously. With a modular design, operators can select from several product configurations, allowing businesses to tailor their offerings according to customer preferences. This modularity not only ensures optimal use of space but also facilitates easy upgrades or changes to beverage options without significant downtime.

The dispenser is engineered with advanced refrigeration technologies, ensuring beverages are chilled to the optimal temperature for serving. Utilizing eco-friendly refrigerants, the system maintains energy efficiency while enhancing the cold retention capabilities of the beverages. The integrated cooling system is designed to maintain consistent temperatures, providing patrons with refreshing drinks every time.

Another hallmark of the Cornelius Cold Beverage Dispenser is its user-friendly interface. The intuitive touch panel allows for quick selection and customization of drinks, enhancing the customer experience. This feature simplifies operations for staff during busy hours, enabling rapid service and reducing wait times.

For maintenance and usability, the dispenser is equipped with a self-diagnostic system that alerts users to any potential issues before they escalate. This proactive feature minimizes downtime and ensures that the dispenser operates smoothly, leading to higher customer satisfaction.

Moreover, the dispenser’s hygienic design is notable. It includes removable components that are easy to clean and sanitize, which is essential in maintaining food safety standards. This characteristic not only prolongs the life of the unit but also contributes to the health and safety of customers.

In summary, the Cornelius Cold Beverage Dispenser combines versatility, advanced technology, and user-friendly features to create a remarkable solution for cold beverage service. With its modular design, energy-efficient refrigeration, intuitive interface, and hygienic construction, it stands out as a premier choice for businesses looking to enhance their beverage offerings while optimizing operational efficiency.
Top Page Image Contents