Blodgett MT1828E manual Electrical Connection, MT1828G Canadian installations

Page 19

Installation

Electrical Connection

Before making any electrical connections to this unit, check that the power supply is adequate for the voltage, amperage, and phase requirements stated on the rating plate.

A wiring diagram accompanies this manual and is also attached to the inside of the control box.

MT1828G

U.S. and Canadian installations

The MT1828G requires a 15 Amp, 60HZ, 1Φ, 208-240VAC, 4 wire service consisting of L1, L2, neutral and ground. Wiring from the power source to these units must be a minimum of #16 AWG copper stranded wire or larger.

General export and Australian installations

The MT1828G requires a 15 Amp, 50 or 60Hz, 1Φ, 220/240 VAC, 3 wire service consisting of L1, neu- tral and ground. Use 90_C wire and size wire ac- cording to local codes.

MT1828E

U.S. and Canadian installations

The MT1828E is available in either 1Φ or 3Φ mod- els. Single phase models require a 60Hz, 208/240VAC, 3 wire service consisting of L1, L2 and ground. Three phase models require a 60Hz, 208/240VAC, 4 wire service consisting of L1, L2, L3 and ground. Wiring from the power source to any of these units must be a minimum of #8 AWG copper stranded wire or larger for 3 phase and #4 AWG for 1 phase.

General export and Australian installations

The MT1828E is available in either 1Φ or 3Φ mod- els. Single phase models require a 50 Hz, 220/240VAC, 3 wire service consisting of L1, L2 and ground. Three phase models are available in either Delta or WYE configurations. Delta models require 50Hz, 208/240VAC, 4 wire service consist- ing of L1, L2, L3 and ground. WYE models require 50 Hz, 415/240 VAC, 5 wire service consisting of L1, L2, L3, neutral and ground. Use a minimum of

8.37mm2 copper stranded wire or larger for 3 phase and 21.15 mm2 for 1 phase.

CAUTION:

Single phase units MUST NOT be connected to the high phase of a three (3) phase system. High phase refers to a potential of 240 volts be- tween one leg and neutral. The remaining two legs will have a potential of 115 volts between each phase and neutral. FAILURE TO DO SO WILL RESULT IN EXTENSIVE DAMAGE TO ELECTRICAL COMPONENTS AND POSSIBLE FIRE IN THE CONTROL BOX.

THE BLODGETT OVEN COMPANY CANNOT AS- SUME RESPONSIBILITY FOR LOSS OR DAMAGE SUFFERED AS A RESULT OF IMPROPERLY IN- STALLED UNITS.

WARNING!!

Incorrect wiring will result in extensive damage to electrical components and possible fire in the control panel.

15

Image 19
Contents MT1828G and MT1828E Avertissement Reputation YOU can Count on Page Table of Contents/Table des Matières Canadian Oven Description and SpecificationsSpecifications MT1828G/AB MT1828E/AAOven Components Emergency Shut Down Switch --- on remote conOff in an emergency. Do not use for general shut down Part Description Qty Delivery and InspectionLocation Canadian installationsGeneral export and Australian installations Oven Location and VentilationOven Stand with Casters Oven AssemblyTriple Stacked Stacking the Ovens if applicable Double StackedConveyor Belt Speed Control GND DC Motor Optional Remote Computer Control Crumb PansUtility Connections --- Standards and Codes Pipe Nominal Size, Inches Length Gas ConnectionGAS Piping ExamplePressure Regulation and Testing Hose See View a GAS Hose RestraintMT1828E Canadian installations MT1828G Canadian installationsElectrical Connection Canadian Installations General safety tips Safety InformationSafety Tips What to do in the event of a power failureProgramming Programming the TemperatureCooking Computer Control DescriptionDisplay Information OperationAIR Flow Adjustments Oven Adjustments for CookingConveyor Speed and Oven Temperature Finished Product TemperaturesPlate Every Six Months CleaningDaily Every Three MonthsEvery 12 Months MT1828G Control Box Component LocationsMT1828E Possible Causes Suggested Remedy Troubleshooting GuideTroubleshooting Guide Description et Spécifications du Four Et Canada CaractéristiquesExportation et l’Australie Bande transporteuse. Ne pas utiliser pour l’arrêt normal Description et Composantes du FourDescription des Pièces Qté Livraison et InspectionAvertissement Implantation et aération du fourImplantation DU Four Aération DU FourBase DE Support DU Four Avec Roulettes Montage du FourSection Triple Superposition DES Fours si applicable Section DoubleLE Convoyeur Speed Control GND DC Motor ’ORDINATEUR DE Cuisson Détaché Plateaux Pour MiettesBranchements de Service --- Normes et Codes Exemple Longeur Dimensions nominales De conduit Pieds ftBranchement de Gaz Conduit DE GAZRéglage ET Test DE Pression Voir VUE a Retenue DU Tuyau DE GAZMT1828E Installations aux États-Unis et au Canada MT1828G Installations aux États-Unis et au CanadaRaccordement Électrique Installations aux États-Unis et au Canada ’arret d’urgence automatique Informations de SécuritéConseils DE Sécurité Que faire en cas de panne de secteurLA Procédé Programmer Identification DES CommandesPour programmer la temperature ’Ordinateur de CuissonAutres Messages DE L’AFFICHEUR UtilisationAjustement DE LA Circulation D’AIR Réglages du Four Pour la CuissonVitesse DU Convoyeur ET Température DU Four Température DES Aliments CuitsUtilisation Tou les trois mois NettoyageMise EN Garde QuotidiennementTou les 12 mois Emplacement des Composants du Boîtier de Commande MT1828E Causes Probables Suggestion Guide de DépannageGuide de Dépannage Insert Wiring Diagram Here Placer Schéma DE Câblage ICI
Related manuals
Manual 2 pages 11.99 Kb

MT1828E, MT1828G specifications

The Blodgett MT1828E and MT1828G are premium commercial convection ovens renowned for their exceptional performance and reliability in professional kitchens. Designed to meet the needs of busy restaurants, catering services, and other food service operations, these ovens are engineered with innovative technologies and features that enhance cooking efficiency and versatility.

One of the standout features of the MT1828E and MT1828G is their digital control system. This user-friendly interface allows chefs to set precise cooking times and temperatures, ensuring consistency in every dish. The digital display provides clear visibility of settings, making it easy to track the progress of meals and adjust parameters as necessary. Additionally, these ovens come equipped with programmable cooking options, enabling users to save and replicate their favorite recipes with just a few taps.

Both models boast a powerful convection fan that promotes even heat distribution throughout the cooking cavity. This results in faster cooking times and beautifully browned dishes, from roasts to baked goods. With a capacity for multiple racks, the MT1828E and MT1828G can accommodate large quantities of food, making them ideal for high-volume cooking environments.

In terms of construction, the Blodgett ovens feature a durable stainless steel exterior that not only enhances their aesthetic appeal but also ensures longevity and ease of maintenance. The interiors are designed to facilitate easy cleaning, reducing downtime in a bustling kitchen. Additionally, they are fitted with double-pane glass doors that provide visibility into the cooking process while minimizing heat loss.

Safety is paramount in commercial cooking equipment, and Blodgett has incorporated several safety features into these models. The ovens include automatic shut-off capabilities, which activate if the doors are left open or if the units overheat, ensuring safe operation even in the busiest environments.

The MT1828E and MT1828G are also energy efficient, helping to reduce utility costs without sacrificing cooking performance. The ovens utilize advanced insulation technology to maintain optimal heat retention, further promoting energy savings.

In summary, the Blodgett MT1828E and MT1828G convection ovens are designed to meet the rigorous demands of professional kitchens. With their digital controls, exceptional airflow, durable construction, and safety features, they stand out as reliable workhorses that can elevate any culinary operation. Whether baking, roasting, or reheating, these ovens offer the versatility and performance that chefs need to succeed.