Blodgett KLS-20G, KLS-40G, KLS-60G manual Installation Installation Codes and Standards

Page 5

2.0INSTALLATION

INSTALLATION CODES AND STANDARDS

Installation must conform with local codes, or in the absence of local codes, with the National Fuel Gas Code, ANSI Z223.1/NFPA 54, or the Natural Gas and Propane Installation Code, CSA B149.1, as applicable.

1.The appliance and its individual shut off valve must be disconnected from the gas supply piping system during any pressure testing of that system at pressures in excess of ½ psi (3.5 kPa).

2.The appliance must be isolated from the gas supply piping system by closing its individual manual shut off valve during any pressure testing of the gas supply piping system at test pressures equal to or less than ½ psi (3.5 kPa).

Electrical grounding must be provided in accordance with local codes, or in the absence of local codes, with the National Electrical Code, ANSI/NFPA 70, or the Canadian Electrical Code, CSA C22.2, as applicable.

The electrical diagram is located on the inside of the console control cover.

EXHAUST FANS AND CANOPIES: Canopies are set over ranges, ovens and kettles for ventilation purposes. It is recommended that a canopy extend 6" past appliance and be located

7.5feet from the floor. Filters should be installed at an angle of 45 degrees or more with the horizontal. This position prevents dripping of grease and facilitates collecting the run-off grease in a drip pan, usually installed with the filter. A strong exhaust fan tends to create a vacuum in the room and may interfere with burner performance or may extinguish pilot flames. Makeup air openings approximately equal to the fan area will relieve such vacuum. In case of unsatisfactory performance on any appliance, check operation with exhaust fan in the “OFF” position.

WALL EXHAUST FAN: The exhaust fan should be installed at least 2 feet above the vent opening at the top of the unit.

CLEARANCES: Adequate clearance must be provided in aisle and at the side and back. Adequate clearances for air openings into the combustion chamber must be provided, as well as for serviceability.

SIDES

-

6 INCHES

BACK

-

2 INCHES AT FLUE BOX

FLOORS -

6 INCH LEGS OR 8 INCH LEGS

All units must be installed in such a manner that the flow of combustion and ventilation air are not obstructed. Provisions for an adequate air supply must also be provided. Do not obstruct the lower front or right side of the unit, as combustion air enters through these areas. The bottom of the control area must also remain unobstructed.

5

Image 5
Contents KLS-20G, KLS-40G and KLS-60G Important Notes for Installation and Operation Table of Contents Description Utility Information Service ConnectionsSides Inches Back Inches AT Flue BOX Floors Installation Installation Codes and StandardsGAS Connection InstallationTo Install Water Connection Installation Installation Performance Check Startup OperationGAS Control Instructions Relighting Shutdown StandbyComplete Wait a Minimum of 5 Minutes Before Proceeding Spark Igniter FailureFront Panel Controls END User Tips Daily OperationGAS Saving Tips END User TipsMonthly MaintenanceDaily Cleaning Instructions Dairy DRAW-OFF Valve Cleaning Cleaning InstructionsDRAW-OFF Valve Cleaning Stainless Steel What to do if Surface Rust AppearsCleaning Instructions Stainless Steel Orifice Size Service GeneralUnit Total Input Natural Manifold PressureGAS Pressure Regulator Pilot Orifice SizesNatural Propane Thermostat AdjustmentsPressure Switch To Adjust Pressure Switch Pressure SwitchControl Circuit Fuses Adding WaterRE-ESTABLISHING Vacuum Converting Between Natural and Propane GAS Converting Between Natural and Propane GAS Troubleshooting Problem Look for Troubleshooting Problem Look for DOW Chemical Canada INC ProductCOMPOSITION/INFORMATION on Ingredients CAS#Hazards Identification Emergency Overview Flammability Limits First AIDFire Fighting Measures Flammable Properties Handling and Storage Stability and Reactivity Exposure CONTROLS/PERSONAL ProtectionPhysical and Chemical Properties Environmental Fate MutagenicityTransport Information Toxic Substances Control ACT Tsca RegulationsChemical Name CAS Number List PA1Other Information Canadian RegulationsCanadian Environmental Protection ACT Cepa

KLS-40G, KLS-60G, KLS-20G specifications

Blodgett KLS series ovens, specifically the KLS-20G, KLS-40G, and KLS-60G, represent the pinnacle of cooking technology designed for both commercial kitchens and culinary professionals. These ovens are engineered to meet diverse cooking needs while delivering exceptional performance, making them invaluable assets in any bustling food service environment.

The KLS-20G, KLS-40G, and KLS-60G models differ primarily in their cooking capacities, with each model tailored for a specific scale of operations. The KLS-20G, with its compact design, is perfect for smaller establishments or those requiring flexibility in their kitchen space. The KLS-40G and KLS-60G, on the other hand, are suited for larger operations that demand increased production capabilities.

One of the standout features of the KLS series is its innovative cooking technology. Each oven is equipped with advanced digital controls that allow for precise temperature management and programmable cooking settings. This ensures consistent results every time, maximizing food quality and minimizing waste. The ovens also incorporate a highly efficient convection cooking system, which circulates hot air evenly throughout the cooking chamber, promoting faster and more uniform cooking.

Additionally, Blodgett’s self-cleaning technology sets these models apart from competitors. This feature significantly reduces labor costs and time spent on maintenance, allowing kitchen staff to focus on food preparation rather than cleaning. Furthermore, the ovens are designed with durability in mind, utilizing high-quality stainless steel that withstands the rigors of a busy kitchen environment.

Energy efficiency is another core characteristic of the KLS series. With features like insulated doors and optimized heating elements, these ovens reduce energy consumption while maintaining high performance levels. This not only lowers operational costs but also contributes to a more sustainable kitchen.

In terms of versatility, Blodgett KLS ovens are equipped with multiple cooking modes such as steam, convection, and a combination of both. This allows chefs to experiment with various culinary techniques across a wide range of dishes, from baking to roasting, broiling, and steaming.

In summary, the Blodgett KLS-20G, KLS-40G, and KLS-60G ovens are engineered to enhance performance and efficiency in professional kitchens. With features like advanced digital controls, superior cooking technology, self-cleaning capabilities, and energy efficiency, these ovens are designed to meet the demands of modern culinary operations, enabling chefs to create exceptional dishes with ease and precision.