Desa SBVBP installation manual Installing LOGS, Lava ROCK, and Glowing Embers

Page 18

18

CAST IRON STOVE AND B-VENT BURNER SYSTEM INSTALLATION

Installing Logs, Lava Rock, and Glowing Embers

CAST IRON STOVE AND B-VENT BURNER SYSTEM INSTALLATION

Continued

INSTALLING LOGS, LAVA ROCK, AND GLOWING EMBERS

WARNING: Failure to position the parts in accor- dance with these diagrams or failure to use only parts specificallyapprovedwiththisburnersystemmayresult in property damage or personal injury.

It is very important to install these logs exactly as instructed in Figures 42 through 46 . Do not modify logs. Only use logs supplied with freestanding burner system. Do not use if any log(s) are broken (see Replacement Parts, page 26).

1.Remove glass door. See Removing/Replacing Glass Door, page 17.

2.Place log #1 (back log) on top of grate. Make sure the notches in the bottom of the log fit over the grate (see Figure 42).

3.Rest log #2 (large front log) on the pins on the front part of the grate (see Figure 43).

4.Place log #3 (crossover log) onto the rear and front logs. Make sure it is seated properly into the notch on the front log and over the raised triangular portion of the rear log as shown in Figure 44.

5.Place log #4 (small log) onto the front left part of the grate making sure the notches fits over the prong of the grate. See Figure 45.

6.Lava rock may be placed along sides and front inside burner system bottom. This may not be visible when you have re- placed the front of the stove. It is not necessary to use all of the lava rock provided.

NOTICE: Do not put lava rock on burner or under burner. Placing lava rock on burner could cause performance problems.

7.Pull ember material apart into pieces no larger than a dime. Place these pieces loosely and sparingly directly onto the ex- posed section of the front burner and along the space between the burner and grate prongs (see Figure 46). This will create the glowing ember appearance as the flame touches the ember material. Do not block air slots by using too much ember ma- terial in one area. It is not necessary to use all of the ember material provided.

8.Replace the glass door and stove front. See Removing/Re- placing Glass Door, page 17.

WARNING: The glass door must be securely in place before running this burner system. Do not run this burner system if glass is missing or broken.

3

4

 

1

2

Figure 44 - Installing Log No. 3 Figure 45 - Installing Log No. 4

Figure 42 - Installing Log No. 1

Figure 43 - Installing Log

 

 

No. 2

 

 

Figure 46 - Placing Ember Material on Burner

For

.

.com

112127-01B

Image 18
Contents VH series Stove For Your SafetyFor Your Safety What to do if YOU Smell GAS Series StoveTable of Contents Safety InformationProduct Identification Product Features PRE-INSTALLATION PreparationLocal Codes Cast Iron Stove and B-VENT Burner System Assembly Stove Body AssemblyAmity Models Removing Front Surround PanelRemoving Screen Optional Oxford or Victor Hearth ModelsInstalling B-VENT Burner System Into Stove Body Installing Optional Blower AccessoryInstalling Rear Cover Securely in place before venting pipes are installedVenting Installation Installation PrecautionsChecking Vent Capacity VerticalHigh Altitude Installation ChimneysRelining Systems Flue GAS Spillage Troubleshooting Venting ProblemsCast Iron Stove and B-VENT Burner System Installation Causes of Spillage and Corrective ActionInstalling GAS Piping to Stove Location Installation Items NeededChecking GAS Connections Connecting STOVE/BURNER System to GAS SupplyPressure Testing Gas Supply Piping System Test Pressures In Excess Of 1/2 Psig 3.5 kPaPressure Testing Burner System Gas Connections Installing Optional Wall Mount Switch GWMS2Installing Optional Wall Mounted Thermostat GWMT1 Will occurInstalling Remote Receiver Installing Battery in ReceiverInstalling 9-Volt Battery in Hand-Held Remote Control Unit REMOVING/REPLACING Glass DoorInstalling LOGS, Lava ROCK, and Glowing Embers Remove glass door. See Removing/Replacing Glass Door,Lighting Instructions For Your Safety Read Before LightingOperating Stove with B-VENT Burner System To Turn OFF GAS To ApplianceOperating Stove with Vent Burner System Optional Remote Thermostat Series OperationON/OFF Series Models Ghrcb and Cghrcb Inspecting Burners Operating Optional Blower AccessoryPilot Assembly Operating Optional GWMT1 Wall Mounted ThermostatPilot and Burners Cleaning MaintenanceGlass Door LogsTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Gas leak. See Warning statement AboveWiring Diagram Replacement PartsTechnical Service Service HintsSpecifications Sbvbnd SbvbpdIllustrated Parts Breakdown Models Sbvbnd and SbvbpdParts List KEY Part Number Description QTYIndicates Color Suffix Designation Oxford Amity Stove BodyVictor Hearth Stove Body Indicates Color Suffix Designation Description QTYTHERMOSTATICALLY- Controlled Blower KIT CDA3620TB AccessoriesReceiver and HAND-HELD Remote Control KIT Ghrcb and Cghrcb Stove Hearth Base GC10SPAOwners Registration Form Postage Required 112127-01B Warranty Information