Desa SBVBP Cast Iron Stove and B-VENT Burner System Assembly, Stove Body Assembly

Page 5

PRE-INSTALLATION PREPARATION

Location and Space Requirements (Cont.)

CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLY

Stove Body Assembly

5

PRE-INSTALLATION PREPARATION

Continued

4" 4"

Figure 4 - Clearance for Corner Installation

26 1/4"

Front

19 1/2"

7.Carefully lay stove body on back to attach bottom components to stove body (see Figure 7). Rest stove on drop cloth or blanket to avoid scratching stove edges.

8.Remove remaining pallet wood attached to bottom of stove body (see Figure 8). Use an adjustable wrench to remove bolts.

9.Fasten each leg to stove with four (4) M8 x 1.25 - 20mm bolts. Use a flat washer and lock washer with each bolt. Tighten bolts into threaded holes on stove body (see Figure 9 and Figure 10 on page 6). Use an adjustable wrench or a 12mm socket.

Bolt

Back Stove

Panel

Figure 6 - Removing Back Panel (Amity™ Only)

Figure 5 - Stove With Burner System Bottom Dimensions

CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLY

STOVE BODY ASSEMBLY

1.

Lift off corrugated box enclosing stove body crating.

2.

Remove all screws fastening the wood frame enclosure. Spread wood

Top of Stove Unit

Front of

Stove

Unit

Drop

Cloth/

Blanket

Front of

Top of

Stove

Stove Unit

Unit

 

Pallet

Wood

Bolted to

Bottom of

Stove

Body

frame open and lift away from plastic-bagged stove body. The bot-

tom pieces of pallet wood will remain bolted to the stove body.

Figure 7 - Laying Down Stove On Side

Front

3.Remove plastic bag from stove body.

4.Locate the product identification label on the carton and record the model number and 7 digit serial number in the space provided in the back of this owner’s manual. Retain this operation and installa- tion manual for future reference and warranty.

Bolt

Pallet

 

Wood

Pallet Wood

Bottom Of

Stove Unit

 

5.Amity Only: Remove back panel from stove and discard (see Figure 6). Use an adjustable wrench or a 10 mm socket. Re- move six (6) bolts and washers. Keep bolts and washers to reattach rear cover.

6.Remove all contents from inside stove cavity. Contents include:

(1)- Stove bottom [Amity Only] (Discard - Not used with this application)

(4)- Legs with leg leveler bolts

(1)- Bottom door

(3)- Top grates

(1)- Hardware kit bag with fasteners

Figure 8 - Removing Pallet Wood From The Bottom of The Stove

Door Hinge

Front

Door Catch Bolt

Step Bolt Hole

 

With Adjustable

 

 

 

 

Hex Nuts Hole

Bottom Of

Stove Unit

Leg Hole

Figure 9 - Locating Threaded Holes for Legs and Door Attachment

For morevisit www..com

112127-01B

Page 4 Page 6
Image 5
Page 4 Page 6
Contents For Your Safety What to do if YOU Smell GAS For Your SafetyVH series Stove Series StoveSafety Information Table of ContentsProduct Identification Local Codes Product FeaturesPRE-INSTALLATION Preparation Stove Body Assembly Cast Iron Stove and B-VENT Burner System AssemblyRemoving Screen Optional Removing Front Surround PanelAmity Models Oxford or Victor Hearth ModelsInstalling Optional Blower Accessory Installing B-VENT Burner System Into Stove BodySecurely in place before venting pipes are installed Installing Rear CoverInstallation Precautions Venting InstallationVertical Checking Vent CapacityRelining Systems High Altitude InstallationChimneys Cast Iron Stove and B-VENT Burner System Installation Troubleshooting Venting ProblemsFlue GAS Spillage Causes of Spillage and Corrective ActionInstallation Items Needed Installing GAS Piping to Stove LocationPressure Testing Gas Supply Piping System Connecting STOVE/BURNER System to GAS SupplyChecking GAS Connections Test Pressures In Excess Of 1/2 Psig 3.5 kPaInstalling Optional Wall Mounted Thermostat GWMT1 Installing Optional Wall Mount Switch GWMS2Pressure Testing Burner System Gas Connections Will occurInstalling Battery in Receiver Installing Remote ReceiverREMOVING/REPLACING Glass Door Installing 9-Volt Battery in Hand-Held Remote Control UnitRemove glass door. See Removing/Replacing Glass Door, Installing LOGS, Lava ROCK, and Glowing EmbersOperating Stove with B-VENT Burner System For Your Safety Read Before LightingLighting Instructions To Turn OFF GAS To ApplianceON/OFF Series Models Ghrcb and Cghrcb Operating Stove with Vent Burner SystemOptional Remote Thermostat Series Operation Pilot Assembly Operating Optional Blower AccessoryInspecting Burners Operating Optional GWMT1 Wall Mounted ThermostatGlass Door Cleaning MaintenancePilot and Burners LogsObserved Problem Possible Cause TroubleshootingObserved Problem Possible Cause Remedy Above Gas leak. See Warning statementTechnical Service Replacement PartsWiring Diagram Service HintsSbvbnd Sbvbpd SpecificationsModels Sbvbnd and Sbvbpd Illustrated Parts BreakdownKEY Part Number Description QTY Parts ListVictor Hearth Stove Body Indicates Color Suffix Designation Oxford AmityStove Body Description QTY Indicates Color Suffix DesignationReceiver and HAND-HELD Remote Control KIT Ghrcb and Cghrcb AccessoriesTHERMOSTATICALLY- Controlled Blower KIT CDA3620TB Stove Hearth Base GC10SPAOwners Registration Form Postage Required 112127-01B Warranty Information
Top Page Image Contents