Desa SBVBP Removing Front Surround Panel, Removing Screen Optional, Amity Models

Page 6

6

CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLY

Stove Body Assembly (Cont.)

CAST IRON STOVE AND B-VENT BURNER SYSTEM ASSEMBLY

Continued

10.Attach stove door by inserting step bolt through door hinge pivot hole and into threaded hole in stove body (see Figure 11 and Figure 9 on page 5). Use an adjustable wrench or a 12mm socket to fasten step bolt. Tighten step bolt until snug. Make sure door moves freely.

11.Install door catch bolt (M8 x 1.25-55mm with two M8 hex nuts) into threaded hole on stove body (see Figure 9, page 5). Use an adjustable wrench or a 12mm socket. The catch bolt has two hex nuts attached to it (see Figure 12). The top nut is a bolt stop and the bottom nut is for door leveling adjustment.

12.Check general catch bolt alignment with door claw. Make fi- nal adjustment and door leveling after stove is in normal stand- ing position.

13.Carefully lift stove back up on its four attached legs.

Removing Front Surround Panel

Remove 2 bolts from bottom of stove and set aside. Remove bolt from the top of the stove to remove the front panel assembly (see Figure 13).

Removing Screen (Optional)

Amity Models

1.Lay the front panel assembly face down on a protected sur- face. Remove the two screws that hold the front plate onto the front surround plate (see Figure 14). Save these screws.

2.Remove the screws and washers that hold the screen onto the front surround plate. Discard these screws, washers, and screen (see Figure 14).

3.Replace the two screws from step 1 to reassemble the front plate and the front surround plate. Set this assembly aside un- til burner system has been installed, logs have been placed inside of burner system, and glass door to burner system insert has been replaced.

Oxford or Victor Hearth Models

1.Lay the front panel assembly face down on a protected sur- face. Remove the screws and washers that hold the screen onto the front surround plate. Discard these screws, washers, and screen (see Figure 14).

2.Set this assembly aside until burner system has been installed, logs have been placed inside of burner system, and glass door to burner system insert has been replaced.

Stove Body

Bolt

Front

Assembly

Washers

Bottom Of

 

 

 

 

 

 

 

 

 

Bolt

Stove Unit

 

 

 

 

 

Leg

 

Figure 13 - Removing Front Assembly (Oxford™ Model Shown)

Figure 10 - Attaching Stove Legs (Oxford™ Model Shown)

Front

Screws

 

 

 

 

Screw with

 

 

 

Surround

 

Washer

 

 

 

Plate

 

 

 

 

 

 

Stove Door

 

 

 

 

 

Threaded

Door

Bolt Stop

Screw with

 

 

Hole

 

 

 

 

 

Washer

 

Screen

Door Hinge

 

 

 

 

 

 

 

 

Screen

 

 

Step

Door Claw

Adjusting

 

 

Front Surround

 

 

Plate and

Bolt

Nut

 

 

 

Front Plate

 

Doors

 

 

 

 

 

Catch Bolt

 

Amity™ Model

Oxford™ or Victor Hearth™

 

 

 

 

Models

Bolt Shoulder

 

 

 

 

Figure 12 - Catch Bolt and

Figure 14 - Removing Screen from Front Assembly

Figure 11 - Attaching Stove Door

Door Claw Orientation

 

 

 

For..com

112127-01B

Image 6
Contents VH series Stove For Your SafetyFor Your Safety What to do if YOU Smell GAS Series StoveTable of Contents Safety InformationProduct Identification Product Features PRE-INSTALLATION PreparationLocal Codes Cast Iron Stove and B-VENT Burner System Assembly Stove Body AssemblyAmity Models Removing Front Surround PanelRemoving Screen Optional Oxford or Victor Hearth ModelsInstalling B-VENT Burner System Into Stove Body Installing Optional Blower AccessoryInstalling Rear Cover Securely in place before venting pipes are installedVenting Installation Installation PrecautionsChecking Vent Capacity VerticalHigh Altitude Installation ChimneysRelining Systems Flue GAS Spillage Troubleshooting Venting ProblemsCast Iron Stove and B-VENT Burner System Installation Causes of Spillage and Corrective ActionInstalling GAS Piping to Stove Location Installation Items NeededChecking GAS Connections Connecting STOVE/BURNER System to GAS SupplyPressure Testing Gas Supply Piping System Test Pressures In Excess Of 1/2 Psig 3.5 kPaPressure Testing Burner System Gas Connections Installing Optional Wall Mount Switch GWMS2Installing Optional Wall Mounted Thermostat GWMT1 Will occurInstalling Remote Receiver Installing Battery in ReceiverInstalling 9-Volt Battery in Hand-Held Remote Control Unit REMOVING/REPLACING Glass DoorInstalling LOGS, Lava ROCK, and Glowing Embers Remove glass door. See Removing/Replacing Glass Door,Lighting Instructions For Your Safety Read Before LightingOperating Stove with B-VENT Burner System To Turn OFF GAS To ApplianceOperating Stove with Vent Burner System Optional Remote Thermostat Series OperationON/OFF Series Models Ghrcb and Cghrcb Inspecting Burners Operating Optional Blower AccessoryPilot Assembly Operating Optional GWMT1 Wall Mounted ThermostatPilot and Burners Cleaning MaintenanceGlass Door LogsTroubleshooting Observed Problem Possible CauseObserved Problem Possible Cause Remedy Gas leak. See Warning statement AboveWiring Diagram Replacement PartsTechnical Service Service HintsSpecifications Sbvbnd SbvbpdIllustrated Parts Breakdown Models Sbvbnd and SbvbpdParts List KEY Part Number Description QTYIndicates Color Suffix Designation Oxford Amity Stove BodyVictor Hearth Stove Body Indicates Color Suffix Designation Description QTYTHERMOSTATICALLY- Controlled Blower KIT CDA3620TB AccessoriesReceiver and HAND-HELD Remote Control KIT Ghrcb and Cghrcb Stove Hearth Base GC10SPAOwners Registration Form Postage Required 112127-01B Warranty Information