Frigidaire 318201679 (0903) Moving the Appliance for Servicing and Cleaning, Range Installation

Page 10

30" DUAL FUEL SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with an Electric Oven and a Gas Cooktop)

7.Moving the Appliance for Servicing and Cleaning

Turn off the range line fuse or circuit breakers at the main power source, and turn off the manual gas shut-off valve. Make sure the range is cold. Remove the service drawer (warmer drawer on some models) and open the oven door. Lift the range at the front and slide it out

of the cut-out opening without creating undue strain on the flexible gas conduit. Make sure not to pinch the flexible gas conduit at the back of the range when replacing the unit into the cut-out opening. Replace the drawer, close the door and switch on the electrical power and gas to the range.

8.Range Installation

Important Note: Door removal is not a requirement for installation of the range, but is an added convenience. Refer to the Use and Care Guide for oven door removal instructions.

Figure 11

Standard Installation

The range cooktop overlaps the countertop at the

1sides and the range rests on the floor. The cooktop is 31½" (80 cm) wide.

Install base cabinets 30" (76.2 cm) apart. Make sure they are plumb and level before attaching cooktop.

2Shave raised countertop edge to clear 31½" (80 cm) wide range top rim.

3Install cabinet doors 31" (78.7 cm) min. apart so as not to interfere with range door opening.

4Cutout countertop exactly as shown on page 1.

5Make sure the four leveling legs are setup higher than the height of the cabinet (shown on page 3).

Install the anti-tip bracket at this point before placing the range at its final

6position. Follow the installation instructions on page 13 or on the anti-tip bracket template supplied with the range.

To provide an optimum installation, the top surface of the countertop must be level and flat (lie on the

7same plane) around the 3 sides that are adjacent to range cooktop. Proper adjustments to make the top flat should be made or gaps between the countertop and the range cooktop may occur.

To reduce the risk of damaging your

8appliance, do not handle or manipulate it by the cooktop. Manipulate with care.

9Position range in front of the cabinet opening.

Make sure that the underside of the cooktop clears

10the countertop. If necessary, raise the unit by lowering the front leveling legs and the back leveling wheels.

Level the range (see section 9). The floor where

11the range is to be installed must be level. Follow the instructions under "Leveling the Range".

12Slide the range into the cutout opening.

IMPORTANT If Accessories Needed :

Installation With Backguard

The cutout depth of (21 3/4" (55.2 cm)Min., 22 1/8" (56.2cm) Max.) needs to be increased to 24" (61 cm) when installing a backguard.

Installation With End Panel

A End Panel kit can be ordered through a Service Center.

Installation With Side Panels

A Side Panels kit can be ordered through a Service Center. Note: Install cabinet doors 31" (78.7 cm) min. apart so as not to interfere with range door opening.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Appliances Installed in the state of Massachusetts MinBy the leveling legs and not by the cooktop itself Side PanelEdge To Clear ShaveRaised Space for aImportant Notes to the Installer Important Note to the ConsumerAccess to Terminal Block & Grounding Strap U.S.A Factory Connected Power Supply Cord Canada onlyPower Supply Cord Kit U.S.A Electrical Shock HazardThree Conductor Wire Connection to Range Four Conductor Wire Connection to RangeWire Electrical System Example Junction Box Connection to Pressure Regulator Gas Supply InstallationCountertop Preparation If the existing cutout width is greater thanSuppl LP/Propane Gas ConversionMoving the Appliance for Servicing and Cleaning Range InstallationLeveling the Range Adjust the LOW Setting of Surface Burner Valves see FigureCheck Operation Model and Serial Number Location When All Hookups are CompleteSerial Plate Location Before You Call for Service Operation of Oven ElementsInstructions Anti-Tip Brackets InstallationTools Required Aparatos Instalados en el estado de Massachusetts No trate de encender ningún artefactoLa superficie debe estar plana y Nivelada area sombreada Conducto flexible de gas entre la estufa y Apoyada en las patas de nivelación y no en el vidrio liso22 7/8 58.1 cm min 23 1/4 59.05 cm max Nota 86 cm Figura Notas importantes para el Instalador Nota Importante para el ConsumidorPeligro de choque eléctrico Estuche de cable del suministro eléctrico U.S.AEléctricos Conexión del cable a tres alambres la cocina Conexión eléctrica a la cocina Estados UnidosConexión del cable de cuatro conductores a la cocina Alambre neutral blanco juntos Desconecte el suministro eléctricoAlambres vea figura Conecte los dos alambres negros juntosConecte el Regulador de Presión Construcción del armarioPreparación del mostrador 31½Conversión para uso de Propano Líquido InglesaLa mudanza del aparato para reparaciones o limpieza Instalación con el repuestoAjuste bajo LOW para la válvula dual Fig Instala las Bases y las tapas de los QuemadoresLa nivelación Funcionamiento de los Elementos del Horno Después de Terminar la InstalaciónUbicación del Número de Modelo y de Serie Antes de Llamar al ServicioInstrucciones de instalación de la fijación anti-inclinación Herramientas NecesariasNinstallez pas Appareils installée dans létat du MassachusettsLappareil dans le cabinet avant Four 22 7/8 58.1 cm min 23 1/4 59.05 cm max Voir noteUisso Afin dinstallerAbl CorrectementInstructions DE Sécurité Importantes Accès au bloc de connexions et à la plaque de mise à terre Canada seulementEnsemble de cordon dalimentation États-Unis Risque de choc électriqueGauche Cuisinière U.S.ARouge à la borne de droite, et le fil noir à la borne de Abaissez le couvercle des bornes du bloc deDe lappareil et le fil neutre blanc du câble Débranchez lalimentationReliez ensemble, le fil blanc, le fil vert dénudé DalimentationConstruction de l’armoire Alimentation en gaz InstallationPréparation du dessus de comptoir ’appareil Ligne Installation dune moulure arrière Installation StandardInstallation avec un dosseret Assurez-vous que les pattes de nivellement sontMise à niveau de la cuisinière Mise en place des couvercles et des grilles des brûleursFonctionnement éléments du four Convection certains modèles- Lorsque le four est régléInstructions d’installation des Supports anti‑bascules Outils Requis

CPDS3085KF, 318201679 (0903) specifications

The Frigidaire 318201679 (0903) is a premium oven replacement part designed for the CPDS3085KF model, enhancing the cooking experience with its advanced features and technologies. With a focus on reliability and efficiency, this appliance part stands out as a key element in ensuring optimal performance for home chefs.

One of the main features of the Frigidaire 318201679 is its high-quality construction, designed to withstand the rigors of daily cooking. It is built with durable materials, making it resistant to wear and tear associated with constant use. This durability not only extends the life of the oven but also ensures consistent cooking results over time.

The part is engineered with precision, making installation straightforward and user-friendly. Homeowners can replace the oven part with minimal effort, ensuring that their cooking appliance returns to full functionality without the need for professional assistance. This ease of installation is a notable advantage for those who prefer to handle repairs themselves.

In terms of technology, the Frigidaire 318201679 benefits from modern advancements that enhance its operability. It features advanced heating and cooking technologies that promote even heat distribution, ensuring that food is cooked uniformly. This eliminates the common problem of hot spots, providing a more satisfactory cooking experience.

Another characteristic worth mentioning is the component's compatibility with various cooking styles. Whether baking, roasting, or broiling, the 318201679 delivers reliable performance, making it an excellent choice for diverse culinary applications. Its versatility aligns with the needs of today’s home cooks, who seek both convenience and quality in their kitchen appliances.

Additionally, this part is designed for energy efficiency, helping consumers save on energy costs while minimizing their environmental impact. By optimizing power usage, the Frigidaire 318201679 not only supports sustainable cooking practices but also contributes to lower utility bills.

In summary, the Frigidaire 318201679 (0903) is an essential component for the CPDS3085KF oven, featuring robust construction, user-friendly installation, advanced cooking technologies, versatility, and energy efficiency. These characteristics collectively enhance the cooking experience, making it a reliable choice for any culinary enthusiast.
Top Page Image Contents