Frigidaire CPDS3085KF, 318201679 (0903) installation instructions Suppl, LP/Propane Gas Conversion

Page 9

30" DUAL FUEL SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with an Electric Oven and a Gas Cooktop)

Manual

Flare

GAS FLOW

Flare

Pressure

Shutoff

 

Regulator

Union

 

Union

Valve

 

 

 

 

 

 

On

Nipple

 

Nipple

 

Off

Flexible

Access

 

Connector

 

 

 

 

Cap

 

 

 

 

All connections must be wrench-tightened

 

 

Figure 9

 

 

Assemble the flexible connector from the gas supply pipe to the pressure regulator in the following order:

1.manual shutoff valve (not supplied)

2.1/2" nipple (not supplied)

3.1/2" flare union adapter (not supplied)

4.flexible connector (not supplied)

5.1/2" flare union adapter (not supplied)

6.1/2" nipple (not supplied)

7.pressure regulator (supplied)

The gas supply line to the shutoff valve should be 1/2"(1,27 cm) or 3/4"(1.9 cm) solid pipe.

The user must know the location of the main shutoff valve and have easy access to it.

When using flexible gas conduit on the range, allow sufficient slack to pull the range outside the cutout for cleaning or servicing.

NOTE: Do not allow the flexible conduit to get pinched between the wall and the range. To visually check, remove the range drawer.

Use pipe-joint compound made for use with Natural and LP/Propane gas to seal all gas connections. If flexible connectors are used, be certain connectors are not kinked.

to

 

 

appliance

 

 

 

to

 

 

gas

suppl

 

 

 

 

y

Shutoff Valve -

 

line

 

 

Open position

 

 

Figure 10

 

 

Once regulator is in place, open the shutoff valve in the gas supply line. Wait a few minutes for gas to move through the gas line.

Leak testing of the appliance shall be conducted according to the manufacturer's instructions.

Check for leaks. After connecting the range to the gas supply, check the system for leaks with a manometer. If a manometer is not available, turn on the gas supply and use a liquid leak detector at all joints and connections to check for leaks.

Do not use a flame to check for leaks from gas connections. Checking for leaks with a flame may result in a fire or explosion.

All openings in the wall or floor where the range is to be installed must be sealed.

Tighten all connections if necessary to prevent gas leakage in the cooktop or supply line.

Disconnect this range and its individual shutoff valve from the gas supply piping system during any pressure testing of the system at test pressures greater than 1/2 psig (3.5 kPa or 14"(35,56 cm) water column).

Isolate the range from the gas supply piping system by closing its individual manual shutoff valve during any pressure testing of the gas supply piping system at test pressures equal to or less than 1/2 psig (3.5 kPa or 14"(35,56 cm) water column).

6.LP/Propane Gas Conversion

This appliance can be used with Natural gas or LP/ Propane gas. It is shipped from the factory for use with natural gas.

If you wish to convert your range for use with LP/ Propane gas, use the supplied fixed orifices located in a bag containing the literature marked "FOR LP/PROPANE GAS CONVERSION." Follow the instructions packaged with the orifices.

The conversion must be performed by a qualified service technician in accordance with the manufacturer's instructions and all local codes and requirements. Failure to follow these instructions could result in serious injury or property damage. The qualified agency performing this work assumes responsibility for the conversion.

Failure to make the appropriate conversion can result in personal injury and property damage.

The supply line must be equipped with an approved manual shutoff valve. This valve should be located in the same room as the range and should be in a location that allows ease of opening and closing. Do not block access to the shutoff valve. The valve is for turning on or shutting off gas to the appliance.

9

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Min Appliances Installed in the state of MassachusettsSide Panel By the leveling legs and not by the cooktop itselfRaised ShaveEdge To Clear Space for aImportant Note to the Consumer Important Notes to the InstallerPower Supply Cord Kit U.S.A Factory Connected Power Supply Cord Canada onlyAccess to Terminal Block & Grounding Strap U.S.A Electrical Shock HazardFour Conductor Wire Connection to Range Three Conductor Wire Connection to RangeWire Electrical System Example Junction Box Countertop Preparation Gas Supply InstallationConnection to Pressure Regulator If the existing cutout width is greater thanLP/Propane Gas Conversion SupplRange Installation Moving the Appliance for Servicing and CleaningAdjust the LOW Setting of Surface Burner Valves see Figure Leveling the RangeCheck Operation Serial Plate Location Before You Call for Service When All Hookups are CompleteModel and Serial Number Location Operation of Oven ElementsAnti-Tip Brackets Installation InstructionsTools Required No trate de encender ningún artefacto Aparatos Instalados en el estado de MassachusettsLa superficie debe estar plana y Nivelada area sombreada Apoyada en las patas de nivelación y no en el vidrio liso Conducto flexible de gas entre la estufa y22 7/8 58.1 cm min 23 1/4 59.05 cm max Nota 86 cm Figura Nota Importante para el Consumidor Notas importantes para el InstaladorEstuche de cable del suministro eléctrico U.S.A Peligro de choque eléctricoEléctricos Conexión eléctrica a la cocina Estados Unidos Conexión del cable a tres alambres la cocinaConexión del cable de cuatro conductores a la cocina Alambres vea figura Desconecte el suministro eléctricoAlambre neutral blanco juntos Conecte los dos alambres negros juntosPreparación del mostrador Construcción del armarioConecte el Regulador de Presión 31½Inglesa Conversión para uso de Propano LíquidoInstalación con el repuesto La mudanza del aparato para reparaciones o limpiezaInstala las Bases y las tapas de los Quemadores Ajuste bajo LOW para la válvula dual FigLa nivelación Ubicación del Número de Modelo y de Serie Después de Terminar la InstalaciónFuncionamiento de los Elementos del Horno Antes de Llamar al ServicioHerramientas Necesarias Instrucciones de instalación de la fijación anti-inclinaciónAppareils installée dans létat du Massachusetts Ninstallez pasLappareil dans le cabinet avant 22 7/8 58.1 cm min 23 1/4 59.05 cm max Voir note FourAbl Afin dinstallerUisso CorrectementInstructions DE Sécurité Importantes Ensemble de cordon dalimentation États-Unis Canada seulementAccès au bloc de connexions et à la plaque de mise à terre Risque de choc électriqueRouge à la borne de droite, et le fil noir à la borne de Cuisinière U.S.AGauche Abaissez le couvercle des bornes du bloc deReliez ensemble, le fil blanc, le fil vert dénudé Débranchez lalimentationDe lappareil et le fil neutre blanc du câble DalimentationAlimentation en gaz Installation Construction de l’armoirePréparation du dessus de comptoir ’appareil Ligne Installation avec un dosseret Installation StandardInstallation dune moulure arrière Assurez-vous que les pattes de nivellement sontMise en place des couvercles et des grilles des brûleurs Mise à niveau de la cuisinièreConvection certains modèles- Lorsque le four est réglé Fonctionnement éléments du fourOutils Requis Instructions d’installation des Supports anti‑bascules

CPDS3085KF, 318201679 (0903) specifications

The Frigidaire 318201679 (0903) is a premium oven replacement part designed for the CPDS3085KF model, enhancing the cooking experience with its advanced features and technologies. With a focus on reliability and efficiency, this appliance part stands out as a key element in ensuring optimal performance for home chefs.

One of the main features of the Frigidaire 318201679 is its high-quality construction, designed to withstand the rigors of daily cooking. It is built with durable materials, making it resistant to wear and tear associated with constant use. This durability not only extends the life of the oven but also ensures consistent cooking results over time.

The part is engineered with precision, making installation straightforward and user-friendly. Homeowners can replace the oven part with minimal effort, ensuring that their cooking appliance returns to full functionality without the need for professional assistance. This ease of installation is a notable advantage for those who prefer to handle repairs themselves.

In terms of technology, the Frigidaire 318201679 benefits from modern advancements that enhance its operability. It features advanced heating and cooking technologies that promote even heat distribution, ensuring that food is cooked uniformly. This eliminates the common problem of hot spots, providing a more satisfactory cooking experience.

Another characteristic worth mentioning is the component's compatibility with various cooking styles. Whether baking, roasting, or broiling, the 318201679 delivers reliable performance, making it an excellent choice for diverse culinary applications. Its versatility aligns with the needs of today’s home cooks, who seek both convenience and quality in their kitchen appliances.

Additionally, this part is designed for energy efficiency, helping consumers save on energy costs while minimizing their environmental impact. By optimizing power usage, the Frigidaire 318201679 not only supports sustainable cooking practices but also contributes to lower utility bills.

In summary, the Frigidaire 318201679 (0903) is an essential component for the CPDS3085KF oven, featuring robust construction, user-friendly installation, advanced cooking technologies, versatility, and energy efficiency. These characteristics collectively enhance the cooking experience, making it a reliable choice for any culinary enthusiast.
Top Page Image Contents