Frigidaire CPDS3085KF Anti-Tip Brackets Installation, Instructions, Tools Required

Page 13

30" DUAL FUEL SLIDE-IN RANGE INSTALLATION INSTRUCTIONS

(Models with an Electric Oven and a Gas Cooktop)

11. Anti-Tip Brackets Installation

Instructions

To reduce the risk of tipping of the range, the range must be secured to the floor by properly installed anti-tip brackets and screws packed with the range. Those parts are located in a plastic bag in the oven. Failure to install the anti-tip brackets will allow the range to tip over if excessive weight is placed on an open door or if a child climbs upon it. Serious injury might result from spilled hot liquids or from the range itself.

Follow the instructions below to install the anti-tip brackets.

If range is ever moved to a different location, the anti- tip brackets must also be moved and installed with the range. To check for proper installation, see step 5.

Tools Required:

5/16" (0,79 cm) Nutdriver or Flat Head Screwdriver Adjustable Wrench

Electric Drill

3/16" (0,48 cm) Diameter Drill Bit

3/16" (0,48 cm) Diameter Masonry Drill Bit (if installing in concrete)

Brackets attach to the floor at the back of the range to hold both rear leg levelers. When fastening to the floor, be sure that screws do not penetrate electrical wiring or plumbing. The screws provided will work in either wood or concrete.

Anti-Tip Bracket

Back Edge of

Range or Rear Wall

CL

 

 

9 1/8”

 

18¼”

(23.2 cm)

(46.4 cm)

 

28 1/8”

Anti-Tip Bracket

(71.4 cm)

(Rear width of range with body sides)

1.Unfold paper template and place it flat on the floor with the back and side edges positioned exactly where the back and sides of range will be located when installed. (Use the diagram below to locate brackets if template is not available (Figure 15)).

2.Mark on the floor the location of the 4 mounting holes shown on the template. For easier installation, 3/16" (0.5 cm) diameter pilot holes 1/2"(1,27 cm) (1.3 cm) deep can be drilled into the floor.

3.Remove template and place brackets on floor with turned up flange to the front. Line up holes in brackets with marks on floor and attach with 4 screws provided. Brackets must be secured to solid floor. If attaching to concrete floor, first drill 3/16" (0.5 cm) dia. pilot holes using a masonry drill bit.

4.Level range if necessary, by adjusting 4 leg levelers with wrench. (See Figure 16 below.) A minimum clearance of 1/8" (0.8 cm) is required between the bottom of the range and the rear leg levelers to allow room for the anti-tip brackets.

5.Slide range into place making sure rear legs are trapped by ends of brackets. Range may need to be shifted slightly to one side as it is being pushed back to allow rear legs to align with brackets. You may also grasp the top rear edge of the range and carefully attempt to tilt it forward to make sure range is properly anchored.

Leveling Leg

Raise

Lower

Figure 16

Slide Back

Figure 15

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Min Appliances Installed in the state of MassachusettsSide Panel By the leveling legs and not by the cooktop itselfRaised ShaveEdge To Clear Space for aImportant Note to the Consumer Important Notes to the InstallerPower Supply Cord Kit U.S.A Factory Connected Power Supply Cord Canada onlyAccess to Terminal Block & Grounding Strap U.S.A Electrical Shock HazardFour Conductor Wire Connection to Range Three Conductor Wire Connection to RangeWire Electrical System Example Junction Box Countertop Preparation Gas Supply InstallationConnection to Pressure Regulator If the existing cutout width is greater thanLP/Propane Gas Conversion SupplRange Installation Moving the Appliance for Servicing and CleaningLeveling the Range Adjust the LOW Setting of Surface Burner Valves see FigureCheck Operation Serial Plate Location Before You Call for Service When All Hookups are CompleteModel and Serial Number Location Operation of Oven ElementsInstructions Anti-Tip Brackets InstallationTools Required Aparatos Instalados en el estado de Massachusetts No trate de encender ningún artefactoLa superficie debe estar plana y Nivelada area sombreada Conducto flexible de gas entre la estufa y Apoyada en las patas de nivelación y no en el vidrio liso22 7/8 58.1 cm min 23 1/4 59.05 cm max Nota 86 cm Figura Nota Importante para el Consumidor Notas importantes para el InstaladorPeligro de choque eléctrico Estuche de cable del suministro eléctrico U.S.AEléctricos Conexión del cable a tres alambres la cocina Conexión eléctrica a la cocina Estados UnidosConexión del cable de cuatro conductores a la cocina Alambres vea figura Desconecte el suministro eléctricoAlambre neutral blanco juntos Conecte los dos alambres negros juntosPreparación del mostrador Construcción del armarioConecte el Regulador de Presión 31½Inglesa Conversión para uso de Propano LíquidoInstalación con el repuesto La mudanza del aparato para reparaciones o limpiezaAjuste bajo LOW para la válvula dual Fig Instala las Bases y las tapas de los QuemadoresLa nivelación Ubicación del Número de Modelo y de Serie Después de Terminar la InstalaciónFuncionamiento de los Elementos del Horno Antes de Llamar al ServicioHerramientas Necesarias Instrucciones de instalación de la fijación anti-inclinaciónNinstallez pas Appareils installée dans létat du MassachusettsLappareil dans le cabinet avant 22 7/8 58.1 cm min 23 1/4 59.05 cm max Voir note FourAbl Afin dinstallerUisso CorrectementInstructions DE Sécurité Importantes Ensemble de cordon dalimentation États-Unis Canada seulementAccès au bloc de connexions et à la plaque de mise à terre Risque de choc électriqueRouge à la borne de droite, et le fil noir à la borne de Cuisinière U.S.AGauche Abaissez le couvercle des bornes du bloc deReliez ensemble, le fil blanc, le fil vert dénudé Débranchez lalimentationDe lappareil et le fil neutre blanc du câble DalimentationConstruction de l’armoire Alimentation en gaz InstallationPréparation du dessus de comptoir ’appareil Ligne Installation avec un dosseret Installation StandardInstallation dune moulure arrière Assurez-vous que les pattes de nivellement sontMise en place des couvercles et des grilles des brûleurs Mise à niveau de la cuisinièreConvection certains modèles- Lorsque le four est réglé Fonctionnement éléments du fourOutils Requis Instructions d’installation des Supports anti‑bascules

CPDS3085KF, 318201679 (0903) specifications

The Frigidaire 318201679 (0903) is a premium oven replacement part designed for the CPDS3085KF model, enhancing the cooking experience with its advanced features and technologies. With a focus on reliability and efficiency, this appliance part stands out as a key element in ensuring optimal performance for home chefs.

One of the main features of the Frigidaire 318201679 is its high-quality construction, designed to withstand the rigors of daily cooking. It is built with durable materials, making it resistant to wear and tear associated with constant use. This durability not only extends the life of the oven but also ensures consistent cooking results over time.

The part is engineered with precision, making installation straightforward and user-friendly. Homeowners can replace the oven part with minimal effort, ensuring that their cooking appliance returns to full functionality without the need for professional assistance. This ease of installation is a notable advantage for those who prefer to handle repairs themselves.

In terms of technology, the Frigidaire 318201679 benefits from modern advancements that enhance its operability. It features advanced heating and cooking technologies that promote even heat distribution, ensuring that food is cooked uniformly. This eliminates the common problem of hot spots, providing a more satisfactory cooking experience.

Another characteristic worth mentioning is the component's compatibility with various cooking styles. Whether baking, roasting, or broiling, the 318201679 delivers reliable performance, making it an excellent choice for diverse culinary applications. Its versatility aligns with the needs of today’s home cooks, who seek both convenience and quality in their kitchen appliances.

Additionally, this part is designed for energy efficiency, helping consumers save on energy costs while minimizing their environmental impact. By optimizing power usage, the Frigidaire 318201679 not only supports sustainable cooking practices but also contributes to lower utility bills.

In summary, the Frigidaire 318201679 (0903) is an essential component for the CPDS3085KF oven, featuring robust construction, user-friendly installation, advanced cooking technologies, versatility, and energy efficiency. These characteristics collectively enhance the cooking experience, making it a reliable choice for any culinary enthusiast.
Top Page Image Contents