Sherwood RD-8601 Introduction, Read This Before Operating Your Unit, English, Fcc Information

Page 2
Introduction

Introduction

READ THIS BEFORE OPERATING YOUR UNIT READ THIS BEFORE OPERATING YOUR UNIT

CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT

REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This symbol is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

This symbol is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

ENGLISH

WARNING : TO REDUCE THE RISK OF FIRE OR ELECTRIC SHOCK,

DO NOT EXPOSE THIS APPLIANCE TO RAIN OR MOISTURE.
Note to CATV System Installer :

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the NEC that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of cable entry as practical.

FCC INFORMATION

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.

Increase the separation between the equipment and receiver.

Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

Caution : Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

FOR YOUR SAFETY

U.S.A

 

CANADA

120 V

Units shipped to the U.S.A and Canada are designed for operation on 120 V AC only.

Safety precaution with use of a polarized AC plug.

However, some products may be supplied with a nonpolarized plug.

CAUTION : To prevent electric shock, match wide blade of plug to wide slot, fully insert.

ATTENTION : Pour éviter chocs électriques, introduire la lame la plus large de la fiche dans la borne correspondante de la prise et pousser jusqu’ au

fond.

Avoid high temperatures. Allow for sufficient heat dispersion when installed on a rack.

Keep the set free from moisture, water, and dust.

Do not let foreign objects in the set.

Handle the power cord carefully. Hold the plug when unplugging the cord.

Unplug the power cord when not using the set for long periods of time.

Do not obstruct the ventilation holes.

Do not let insecticides, benzene, and thinner come in contact with the set.

Never disassemble or modify the set in any way.

2

Image 2
Contents Audio/Video Receiver OPERATING INSTRUCTIONSRD-8601 Introduction Note to CATV System InstallerFOR YOUR SAFETY READ THIS BEFORE OPERATING YOUR UNITSAFETY INSTRUCTION Speaker Setup | CONTENTSUniversal Remote Controls | Using the OSDENGLISH 1. CONNECTING ANTENNAsSystem Connections 2. CONNECTING VIDEO COMPONENTS ENGLISH5. CONNECTING DIGITAL INs and OUT 3. CONNECTING AUDIO COMPONENTS4. CONNECTING EXTERNAL INs ENGLISH7. SUBWOOFER PREOUT connection 6. CONNECTING SYSTEM CONTROL8. CONNECTING SPEAKERS ENGLISHSurround left and right speakers Speaker placementFront left and right speakers and center speaker Surround back speaker11. AC INPUT CORD 9. CONNECTING MICROPHONE10. SWITCHED AC OUTLETs ENGLISHENGLISH Front Panel ControlsFLUORESCENT DISPLAY VIDEO AUDIO OUT OUT VIDEO 3 INPUT JACKSENGLISH VIDEO VIDEO L - AUDIO - RENGLISH Universal Remote ControlsDigi link system remote controls ENGLISH NotesFUNCTION TABLE of the NUMBERED BUTTONS ENGLISH REMOTE CONTROL OPERATION RANGELOADING BATTERIES ENGLISH USING FUNCTIONS OF REMOTE CONTROLEntering a setup code Using a punch-throughfunction ENGLISHENGLISH Programming a macro functionOperating a macro function About the speaker size Speaker SetupENGLISH About the speaker distanceENGLISH SETTING THE SPEAKER SETUP MANUALLYBefore setting the speaker setup Continued ENGLISHConnect the optional microphone to the Before setting the speaker setupENGLISH When specifying the number of speakers installed ENGLISHWhile displaying “SET MEMO”, check ENGLISHLISTENING TO A PROGRAM SOURCE • The STANDBY indicator lights upOperations Before operationENGLISH When CD, VIDEO 1~3 is selected asan input source Adjusting the tonebass and treble ENGLISHDTS Digital Surround SURROUND SOUNDSurround modes DTS - ES Extended SurroundDolby Virtual Speaker Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby HeadphoneENJOYING SURROUND SOUND ENGLISH2CH downmix mode To cancel the surround mode for stereo operationListening in a Dolby Headphone mode ENGLISHAdjusting each channel level with test tone ENGLISHAdjusting the current channel level ENGLISHENGLISH Memorizing the adjusted channel levelsRecalling the memorized channel levels Presetting radio stations Auto tuningManual tuning LISTENING TO RADIO BROADCASTSMEMORY BACKUP FUNCTION Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsRecording with TAPE Dubbing the audio and video signalsRECORDING Dubbing from video components ontoDIGITAL AUDIO RECORDING WITH MD RECORDER ENGLISHOperating the sleep timer OTHER FUNCTIONSCURRENT STATUS DISPLAY Using the OSDOSD Menu Settings ENGLISHWhen selecting the FUNCTION SELECT Select the desired menu using theWhen selecting the SPEAKER SETUP When selecting the SURROUND MODEPreparations SETTING THE SPEAKER SETUPWhen selecting the AUTO SPEAKER SETUP ENGLISHWhen selecting the MANUAL SPEAKER SETUP ENGLISHNotes ENGLISHENGLISH When selecting the DIGITAL INPUTSELECTING THE FUNCTION ENGLISH When selecting the VIDEO SELECTWhen selecting the TONE CONTROL SELECTING THE SURROUND MODE ENGLISHENGLISH SETTING THE CH LEVEL SETUPAdjusting the current channel level the ENTER button Memorizing the adjusted channel levelsENGLISH Recalling the memorized channel levelsPOSSIBLE CAUSE Troubleshooting GuidePROBLEM REMEDYSpecifications ENGLISHSetup Code Table ENGLISHENGLISH ENGLISH HeadquarterENGLISH AUX-TAPE AUX-TAPE/MDAUX-LD AUX-AMPAUX-DBS AUX-ACCESSARYAUX-HOMEAUTOMATION ENGLISHRD-8601 Audio/Video Receiver