Sherwood RD-8601 Tuning to preset stations, Listening to FM stereo broadcasts, English

Page 36
MEMORY BACKUP FUNCTION

Select the desired preset number (1~30) and

Repeat the above steps to to

3 press the MEMORY/ENTER button.

4 memorize other stations.

TUNING/PRESET

 

MEMO/ENTER

 

 

 

 

 

• The station has now been stored in the memory.

MEMORY BACKUP FUNCTION

• A stored frequency is erased from the memory by

The following items, set before the receiver is turned

storing another frequency in its place.

off, are memorized.

• If “MEM” goes off, start again from the above

• INPUT SELECTOR settings

step .

 

• Surround mode settings

 

 

• Preset stations,etc.

Tuning to preset stations

Select the desired preset number.

1

After selecting the tuner as an input

2

source, select the preset tuning mode.

 

 

T/P MODE

TUNING/PRESET

 

 

 

 

or

 

 

PRESET PRESET

• Then “PRESET” lights up.

• When pressing the PRESET +/- buttons on the remote

 

 

control, you need not select the preset tuning mode on

 

 

step .

Listening to FM stereo broadcasts

Scanning preset stations in sequence

• While listening to FM broadcasts.

 

 

FM MODE

 

 

 

P.SCAN

• Each time this button is pressed, the FM mode changes

 

as follows;

 

Stereo mode : “ST” lights up.

 

Mono mode : “ST” goes off.

• The receiver will start scanning the stations in the preset

• When FM stereo broadcasts are poor because of weak

sequence and each station is received for 5 seconds.

• At the desired station, press this button again to stop

broadcast signals, select the FM mono mode to reduce

scanning.

the noise, then FM broadcasts are reproduced in

 

monaural sound.

 

ENGLISH

36

Image 36
Contents OPERATING INSTRUCTIONS RD-8601Audio/Video Receiver Note to CATV System Installer FOR YOUR SAFETYIntroduction READ THIS BEFORE OPERATING YOUR UNITSAFETY INSTRUCTION CONTENTS Universal Remote Controls |Speaker Setup | Using the OSD1. CONNECTING ANTENNAs System ConnectionsENGLISH 2. CONNECTING VIDEO COMPONENTS ENGLISH3. CONNECTING AUDIO COMPONENTS 4. CONNECTING EXTERNAL INs5. CONNECTING DIGITAL INs and OUT ENGLISH6. CONNECTING SYSTEM CONTROL 8. CONNECTING SPEAKERS7. SUBWOOFER PREOUT connection ENGLISHSpeaker placement Front left and right speakers and center speakerSurround left and right speakers Surround back speaker9. CONNECTING MICROPHONE 10. SWITCHED AC OUTLETs11. AC INPUT CORD ENGLISHFront Panel Controls FLUORESCENT DISPLAYENGLISH VIDEO 3 INPUT JACKS ENGLISHVIDEO AUDIO OUT OUT VIDEO VIDEO L - AUDIO - RUniversal Remote Controls Digi link system remote controlsENGLISH Notes FUNCTION TABLE of the NUMBERED BUTTONSENGLISH REMOTE CONTROL OPERATION RANGE LOADING BATTERIESENGLISH USING FUNCTIONS OF REMOTE CONTROL Entering a setup codeENGLISH Using a punch-throughfunction ENGLISHProgramming a macro function Operating a macro functionENGLISH Speaker Setup ENGLISHAbout the speaker size About the speaker distanceSETTING THE SPEAKER SETUP MANUALLY Before setting the speaker setupENGLISH Continued ENGLISHBefore setting the speaker setup ENGLISHConnect the optional microphone to the When specifying the number of speakers installed ENGLISHWhile displaying “SET MEMO”, check ENGLISH• The STANDBY indicator lights up OperationsLISTENING TO A PROGRAM SOURCE Before operationWhen CD, VIDEO 1~3 is selected as an input sourceENGLISH Adjusting the tonebass and treble ENGLISHSURROUND SOUND Surround modesDTS Digital Surround DTS - ES Extended SurroundDolby Pro Logic IIx surround Dolby Pro Logic II surroundDolby Virtual Speaker Dolby HeadphoneENJOYING SURROUND SOUND ENGLISHTo cancel the surround mode for stereo operation Listening in a Dolby Headphone mode2CH downmix mode ENGLISHAdjusting each channel level with test tone ENGLISHAdjusting the current channel level ENGLISHMemorizing the adjusted channel levels Recalling the memorized channel levelsENGLISH Auto tuning Manual tuningPresetting radio stations LISTENING TO RADIO BROADCASTSTuning to preset stations Scanning preset stations in sequenceMEMORY BACKUP FUNCTION Listening to FM stereo broadcastsDubbing the audio and video signals RECORDINGRecording with TAPE Dubbing from video components ontoDIGITAL AUDIO RECORDING WITH MD RECORDER ENGLISHOperating the sleep timer OTHER FUNCTIONSUsing the OSD OSD Menu SettingsCURRENT STATUS DISPLAY ENGLISHSelect the desired menu using the When selecting the SPEAKER SETUPWhen selecting the FUNCTION SELECT When selecting the SURROUND MODESETTING THE SPEAKER SETUP When selecting the AUTO SPEAKER SETUPPreparations ENGLISHWhen selecting the MANUAL SPEAKER SETUP ENGLISHNotes ENGLISHWhen selecting the DIGITAL INPUT SELECTING THE FUNCTIONENGLISH When selecting the VIDEO SELECT When selecting the TONE CONTROLENGLISH SELECTING THE SURROUND MODE ENGLISHSETTING THE CH LEVEL SETUP Adjusting the current channel levelENGLISH Memorizing the adjusted channel levels ENGLISHthe ENTER button Recalling the memorized channel levelsTroubleshooting Guide PROBLEMPOSSIBLE CAUSE REMEDYSpecifications ENGLISHSetup Code Table ENGLISHENGLISH ENGLISH HeadquarterENGLISH AUX-TAPE/MD AUX-LDAUX-TAPE AUX-AMPAUX-ACCESSARY AUX-HOMEAUTOMATIONAUX-DBS ENGLISHRD-8601 Audio/Video Receiver