Sherwood RD-8601 Programming a macro function, Operating a macro function, English

Page 18
Programming a macro function

Programming a macro function

The macro function enables you to program a series of button operations(up to 10) on this remote control into a single button.

You can store up to three separate macro command sequences into “M1”, “M2” and “M3” buttons.

Press and hold down both “ENTER” button

1 and one of three NUMERIC buttons (“1”~“3”) corresponding to “M1”~“M3” buttons for more than 1 second.

Example) When programming a series of button operations into “M1” button.

ENTER

TUNER

1Operating a macro function

If the macro mode is entered, the LED will flicker once.

2

Press the operation buttons you want to

program in order.

Note:

You should press the corresponding DEVICE buttons before pressing each operation button.

Example) When playing a DVD on the DVD player connected to VIDEO 2 jacks of this receiver.

1.Press “AUDIO” button to control this receiver.

2.Press “POWER” button to turn this receiver on.

3.Press “AUDIO” button to control this receiver.

4.Press “VIDEO 2(7)” button to select the desired input source.

5.Press “DVD” button to control the DVD player.

6.Press “POWER” button to turn the DVD player on.

7.Press “DVD” button to control the DVD player.

8.Press “ ” button to start playback.

AUD

AUD

VIDEO 2

POWER ON

 

7

DVD

 

DVD

 

POWER ON

 

ENGLISH

3

Press “ENTER” button.

To remove a macro program

• When removing a macro program, perform the above

 

steps and , but ignore the step .

 

To change a macro program

 

ENTER

 

• When a new macro program is stored into a MACRO

 

button with performing the above steps to , the

 

previous macro program is cleared from the memory

 

of the MACRO button.

If the programming is performed successfully, the LED will flicker twice.

Operating a macro function

Aim the remote control at the REMOTE SENSORs of the components to be controlled and press the MACRO button you want.

Example) When pressing “M1” button.

M1

Notes:

The codes programmed into a MACRO button will be transmitted at an interval of 0.5 seconds. However, some components may not be able to complete one operation in 0.5 seconds and may miss the next code.

In this case, the macro function cannot control the corresponding components correctly.

Be sure to use the remote control within the remote control operation range of the components.

Depending on the operation status of the components, etc., the macro function cannot control the corresponding components correctly.

18

Image 18
Contents OPERATING INSTRUCTIONS RD-8601Audio/Video Receiver Introduction Note to CATV System InstallerFOR YOUR SAFETY READ THIS BEFORE OPERATING YOUR UNITSAFETY INSTRUCTION Speaker Setup | CONTENTSUniversal Remote Controls | Using the OSD1. CONNECTING ANTENNAs System ConnectionsENGLISH 2. CONNECTING VIDEO COMPONENTS ENGLISH5. CONNECTING DIGITAL INs and OUT 3. CONNECTING AUDIO COMPONENTS4. CONNECTING EXTERNAL INs ENGLISH7. SUBWOOFER PREOUT connection 6. CONNECTING SYSTEM CONTROL8. CONNECTING SPEAKERS ENGLISHSurround left and right speakers Speaker placementFront left and right speakers and center speaker Surround back speaker11. AC INPUT CORD 9. CONNECTING MICROPHONE10. SWITCHED AC OUTLETs ENGLISHFront Panel Controls FLUORESCENT DISPLAYENGLISH VIDEO AUDIO OUT OUT VIDEO 3 INPUT JACKSENGLISH VIDEO VIDEO L - AUDIO - RUniversal Remote Controls Digi link system remote controlsENGLISH Notes FUNCTION TABLE of the NUMBERED BUTTONSENGLISH REMOTE CONTROL OPERATION RANGE LOADING BATTERIESENGLISH USING FUNCTIONS OF REMOTE CONTROL Entering a setup codeENGLISH Using a punch-throughfunction ENGLISHProgramming a macro function Operating a macro functionENGLISH About the speaker size Speaker SetupENGLISH About the speaker distanceSETTING THE SPEAKER SETUP MANUALLY Before setting the speaker setupENGLISH Continued ENGLISHBefore setting the speaker setup ENGLISHConnect the optional microphone to the When specifying the number of speakers installed ENGLISHWhile displaying “SET MEMO”, check ENGLISHLISTENING TO A PROGRAM SOURCE • The STANDBY indicator lights upOperations Before operationWhen CD, VIDEO 1~3 is selected as an input sourceENGLISH Adjusting the tonebass and treble ENGLISHDTS Digital Surround SURROUND SOUNDSurround modes DTS - ES Extended SurroundDolby Virtual Speaker Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby HeadphoneENJOYING SURROUND SOUND ENGLISH2CH downmix mode To cancel the surround mode for stereo operationListening in a Dolby Headphone mode ENGLISHAdjusting each channel level with test tone ENGLISHAdjusting the current channel level ENGLISHMemorizing the adjusted channel levels Recalling the memorized channel levelsENGLISH Presetting radio stations Auto tuningManual tuning LISTENING TO RADIO BROADCASTSMEMORY BACKUP FUNCTION Tuning to preset stationsScanning preset stations in sequence Listening to FM stereo broadcastsRecording with TAPE Dubbing the audio and video signalsRECORDING Dubbing from video components ontoDIGITAL AUDIO RECORDING WITH MD RECORDER ENGLISHOperating the sleep timer OTHER FUNCTIONSCURRENT STATUS DISPLAY Using the OSDOSD Menu Settings ENGLISHWhen selecting the FUNCTION SELECT Select the desired menu using theWhen selecting the SPEAKER SETUP When selecting the SURROUND MODEPreparations SETTING THE SPEAKER SETUPWhen selecting the AUTO SPEAKER SETUP ENGLISHWhen selecting the MANUAL SPEAKER SETUP ENGLISHNotes ENGLISHWhen selecting the DIGITAL INPUT SELECTING THE FUNCTIONENGLISH When selecting the VIDEO SELECT When selecting the TONE CONTROLENGLISH SELECTING THE SURROUND MODE ENGLISHSETTING THE CH LEVEL SETUP Adjusting the current channel levelENGLISH the ENTER button Memorizing the adjusted channel levelsENGLISH Recalling the memorized channel levelsPOSSIBLE CAUSE Troubleshooting GuidePROBLEM REMEDYSpecifications ENGLISHSetup Code Table ENGLISHENGLISH ENGLISH HeadquarterENGLISH AUX-TAPE AUX-TAPE/MDAUX-LD AUX-AMPAUX-DBS AUX-ACCESSARYAUX-HOMEAUTOMATION ENGLISHRD-8601 Audio/Video Receiver