Sherwood RD-8601 operating instructions When specifying the number of speakers installed, English

Page 23

When specifying the number of speakers installed.

ENGLISH

Specify the setting condition.

4

When specifying the number of speakers installed.

SPEAKER

SETUP

or

SPK SET

•Each time this button is pressed, the speaker layout changes as follows:

ALL : All speakers

3/2 : 2 front, center and 2 surround speakers

2/2 : 2 front and 2 surround speakers

3/0 : 2 front and center speakers

2/0 : 2 front speakers

When specifying the subwoofer or the crossover frequency.

ADJUST

or

• Each time the ADJUST UP( ) or CURSOR RIGHT( ) button is pressed, the subwoofer changes as follows:

S	No display
(Subwoofer: Yes)	(None)

• Each time the ADJUST DOWN( ) or CURSOR LEFT( ) button is pressed, the crossover frequency(“CUT”) changes within the range of 40~130 Hz in 10 Hz intervals.

•In case that the subwoofer setting is “S”(Subwoofer:Yes), if it is possible to adjust the volume and crossover frequency on your subwoofer, set the volume to about medium level (or slightly less), and set the crossover frequency to the maximum.

Start the auto speaker setup procedure.

5

MEMO/ENTER

or	ENTER

Notes:

•Because the test tones are very loud, ensure there are no infants or small children in the room.

•For best results, ensure the room is as quiet as possible during the auto speaker setup procedure. If there is too much ambient noise, the results may not be satisfactory.

•Loud test tones are output from each speaker.

•To stop the auto speaker setup procedure, press the (MEMORY/) ENTER button.

To retry the procedure, press the (MEMORY/) ENTER button again.

•After the auto speaker setup procedure has been completed, “SET MEMO” will be displayed.

•If “>ERROR<” is displayed, there may be a problem with the speaker or microphone connection.

While displaying “>ERROR<”, to retry the procedure,

press the ADJUST UP( ) or CURSOR RIGHT( ) button and to exit from the procedure, press the ADJUST DOWN( ) or CURSOR LEFT( ) button.

•If retrying the procedure does not fix the problem, turn off the power and check the speaker or microphone connections.

23

Image 23

Contents Audio/Video Receiver OPERATING INSTRUCTIONSRD-8601 READ THIS BEFORE OPERATING YOUR UNIT Note to CATV System InstallerFOR YOUR SAFETY IntroductionSAFETY INSTRUCTION Using the OSD CONTENTSUniversal Remote Controls | Speaker Setup |ENGLISH 1. CONNECTING ANTENNAsSystem Connections ENGLISH 2. CONNECTING VIDEO COMPONENTSENGLISH 3. CONNECTING AUDIO COMPONENTS4. CONNECTING EXTERNAL INs 5. CONNECTING DIGITAL INs and OUTENGLISH 6. CONNECTING SYSTEM CONTROL8. CONNECTING SPEAKERS 7. SUBWOOFER PREOUT connectionSurround back speaker Speaker placementFront left and right speakers and center speaker Surround left and right speakersENGLISH 9. CONNECTING MICROPHONE10. SWITCHED AC OUTLETs 11. AC INPUT CORDENGLISH Front Panel ControlsFLUORESCENT DISPLAY VIDEO VIDEO L - AUDIO - R VIDEO 3 INPUT JACKSENGLISH VIDEO AUDIO OUT OUTENGLISH Universal Remote ControlsDigi link system remote controls ENGLISH NotesFUNCTION TABLE of the NUMBERED BUTTONS ENGLISH REMOTE CONTROL OPERATION RANGELOADING BATTERIES ENGLISH USING FUNCTIONS OF REMOTE CONTROLEntering a setup code ENGLISH Using a punch-throughfunctionENGLISH Programming a macro functionOperating a macro function About the speaker distance Speaker SetupENGLISH About the speaker sizeENGLISH SETTING THE SPEAKER SETUP MANUALLYBefore setting the speaker setup ENGLISH ContinuedConnect the optional microphone to the Before setting the speaker setupENGLISH ENGLISH When specifying the number of speakers installedENGLISH While displaying “SET MEMO”, checkBefore operation • The STANDBY indicator lights upOperations LISTENING TO A PROGRAM SOURCEENGLISH When CD, VIDEO 1~3 is selected asan input source ENGLISH Adjusting the tonebass and trebleDTS - ES Extended Surround SURROUND SOUNDSurround modes DTS Digital SurroundDolby Headphone Dolby Pro Logic IIx surroundDolby Pro Logic II surround Dolby Virtual SpeakerENGLISH ENJOYING SURROUND SOUNDENGLISH To cancel the surround mode for stereo operationListening in a Dolby Headphone mode 2CH downmix modeENGLISH Adjusting each channel level with test toneENGLISH Adjusting the current channel levelENGLISH Memorizing the adjusted channel levelsRecalling the memorized channel levels LISTENING TO RADIO BROADCASTS Auto tuningManual tuning Presetting radio stationsListening to FM stereo broadcasts Tuning to preset stationsScanning preset stations in sequence MEMORY BACKUP FUNCTIONDubbing from video components onto Dubbing the audio and video signalsRECORDING Recording with TAPEENGLISH DIGITAL AUDIO RECORDING WITH MD RECORDEROTHER FUNCTIONS Operating the sleep timerENGLISH Using the OSDOSD Menu Settings CURRENT STATUS DISPLAYWhen selecting the SURROUND MODE Select the desired menu using theWhen selecting the SPEAKER SETUP When selecting the FUNCTION SELECTENGLISH SETTING THE SPEAKER SETUPWhen selecting the AUTO SPEAKER SETUP PreparationsENGLISH When selecting the MANUAL SPEAKER SETUPENGLISH NotesENGLISH When selecting the DIGITAL INPUTSELECTING THE FUNCTION ENGLISH When selecting the VIDEO SELECTWhen selecting the TONE CONTROL ENGLISH SELECTING THE SURROUND MODEENGLISH SETTING THE CH LEVEL SETUPAdjusting the current channel level Recalling the memorized channel levels Memorizing the adjusted channel levelsENGLISH the ENTER buttonREMEDY Troubleshooting GuidePROBLEM POSSIBLE CAUSEENGLISH SpecificationsENGLISH Setup Code TableENGLISH Headquarter ENGLISHENGLISH AUX-AMP AUX-TAPE/MDAUX-LD AUX-TAPEENGLISH AUX-ACCESSARYAUX-HOMEAUTOMATION AUX-DBSAudio/Video Receiver RD-8601