American Panel AP24BC250-3 Keyboard Keys, Key Combinations, On/Off & Start/Stop, Programming Keys

Page 14

KEYBOARD KEYS

AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual

KEYBOARD KEYS

ON/OFF & START/STOP

ON/OFF

START/STOP

PROGRAMMING KEYS

UP

DOWN

SELECT

ENTER

CYCLE KEYS

SOFT CYCLE

HARD CYCLE

SHOCK CYCLE

AUTOMATIC CYCLE

MANUAL CYCLE

UV LIGHT CYCLE

DEFROST CYCLE

PRINT

HEAT PROBE CYCLE

KEY COMBINATIONS

¾Initial Programming state – to initially set the device

o With the display reading "OFF", press and hold (“START/STOP”) for 5 seconds

¾Cycles programming state – to initially set the cycles

o With the display reading "OFF", press (“ENTER”) for 1 second

¾Recipe name programming state – to enter recipe names

o With the display reading "OFF", press (“A”) for 10 seconds

¾Load default values state – to load the standard parameters

o With the display reading "OFF", press (”UP”) for 10 seconds

¾Clear events memory state – to clear obsolete data

o With the display reading "OFF", press + (”UP”+”DOWN”) for 10 seconds

¾Ready To Go state – in order to start a cycle

O If the controller is not "OFF", press “ON/OFF” once.

13

Image 14

Contents E-mail service@americanpanel.com American Panel CorporationREV. E USER’S MANUALREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS CONTROLLER FEATURESINSTALLATION OF REMOTE UNITS INSTALLATION AT THE SAME LEVELMAINTENANCE AND CLEANING PREPARING AND USING THE OPTIONAL PRINTERMAINTENANCE CLEANING THE CONDENSEROPERATING MODES CONTROLLER FEATURESINTRODUCTION PC CONNECTION OPTIONAL OPERATING CYCLESPRINTER OPTIONAL INSTALLATION AT THE SAME LEVEL INSTALLATION OF REMOTE UNITSREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS COMPRESSORINSTALLATION AT DIFFERENT LEVELS CONNECTION PIPING FOR REMOTE CONDENSING UNITSDIMENSIONS INSTALLATIONINSTALLATION WARNINGSCONNECTION TO THE REMOTE UNIT VERIFYING CORRECT INSTALLATIONELECTRICAL AND REFRIGERATION SPECIFICATIONS CONDENSATE DRAINAGE CONNECTIONSTARTING & TESTING THE UNIT SPACES AROUND THE CABINETSHOCK FREEZING USING THE HURRICHILL TECHNOLOGYBLAST CHILLING SOFT CHILL CYCLELOADING PANNING AND LOADINGPANNING CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS ON/OFF & START/STOP KEYBOARD KEYSKEY COMBINATIONS PROGRAMMING KEYSPROGRAMMING c. Enter the default password by pressing, in order, theIf the entered password is wrong the display will show 1. INITIAL PROGRAMMINGThe high food alarm temperature should be left at The high air alarm temperature should be left atThe low air alarm temperature should be left at YES for shock freezers AP24BCF300-3, AP40BCF450-3 The low food alarm temperature should be left atThe P.C. baud rate should be left at NO for blast chillers AP24BC250-3, AP40BC350-3 and go to step r2. PROGRAMMING THE CYCLES AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMINGthen press AUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMINGk. To change the temperature, press p. To change the temperature, pressUV LIGHT CYCLE PARAMETERS PROGRAMMING The defrost type must be left AIR FLOW DEFROST CYCLE PARAMETERS PROGRAMMINGHEATED PROBE CYCLE PARAMETERS PROGRAMMING aa. PressThe LED for SOFT will be steady MANUAL SOFT CYCLE PARAMETERS PROGRAMMINGgg. Press hh. To change the temperature, pressMANUAL HARD CYCLE PARAMETERS PROGRAMMING MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING OPERATION 1. AUTOMATIC MODE - SOFT CHILLalternating 2. MANUAL MODE - SOFT CHILLalternating with 3. HARD CHILL CYCLE 6. DEFROST CYCLE 4. SHOCK FREEZE CYCLE5. UV STERILIZATION CYCLE a. To perform a UV cycle remove all food, then pressc. Press the 7. HEATED FOOD PROBEb. Open the door defrost cycle8. PREPARING AND USING THE OPTIONAL PRINTER OTE To stop any cycle before it has finished, press START/STOPPRINTER d. Enter your password, then pressNOTE The optional printer is delivered fully installed 9. TO CLEAR DATAREMOVING A ROLL OF PAPER MAINTENANCELOADING A ROLL OF PAPER OPERATING THE PRINTERREPLACING THE RIBBON WITH PAPER IN THE PRINTER MAINTENANCE AND CLEANINGCLEANING THE CONDENSER COMPARTMENT WIRING DIAGRAMSCLEANING DO NOT USE ABRASIVES, SOLVENTSAP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual COMPUTER CONNECTION DESCRIPTION PARTS LISTPART # AMERICAN PANEL CORP STANDARD WARRANTYinstalling contractor. It is not covered by this Warranty BLAST CHILLERS / SHOCK FREEZERS ONLYORDERING PRINTER SUPPLIES RIBBON & PAPER