American Panel AP24BC250-3 user manual The high air alarm temperature should be left at

Page 16
The high air alarm temperature should be left at

AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual

INITIAL PROGRAMMING

g. To set the day, press

or

then press

SET DAY

 

 

 

 

 

 

03

 

 

03(day)

 

.

 

 

 

Blinks

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

h. To set the hour, press

or

(be sure to

INITIAL PROGRAMMING

 

 

 

 

continue to press the buttons until the hour and "AM"

SET TIME

 

 

 

 

 

 

 

10:25 AM

 

10(hours)

 

or "PM" show correctly) then press

.

 

 

 

Blinks

 

 

 

 

 

 

 

 

 

 

i.To set the minutes, press The low air alarm temperature should be left at or The high food alarm temperature should be left at then press

Manual background.

INITIAL PROGRAMMING

SET TIME 10:25 AM

25(minutes)

Blinks

INITIAL PROGRAMMING

j. To change the number of probes, press

 

or

AIR PROBES NUMBER?

 

 

 

 

 

1 Blinks

 

 

 

 

1

then press

.

 

 

 

 

The high air alarm temperature should be left at

 

 

140 oF. However, if a change is desired:

 

 

INITIAL PROGRAMMING

 

k. To change the temperature, press

or

 

HIGH AIR ALARM

140 Blinks

 

140 °F

then press

.

 

 

 

 

The low air alarm temperature should be left at

 

 

-35oF *. However, if a change is desired:

 

 

INITIAL PROGRAMMING

 

l. To change the temperature, press

or

 

LOW AIR ALARM

-35 Blinks

 

-35 °F *

then press

.

 

 

 

 

*- 35o F for shock freezers (AP24BCF300-3, AP40BCF450-3) - 5o F for blast chillers (AP24BC250-3, AP40BC350-3)

m. To change the number of probes, press Manual background or

Manual background then press Manual background.

INITIAL PROGRAMMING

FOOD PROBES NUMBER?

1

1 Blinks

NOTE: Standard configuration has only one food probe. However, a maximum of 4 probes can be used with these models.

The high food alarm temperature should be left at

180 oF. However, to make a change:

n.To change the temperature, press Manual background or Manual background

then press Manual background.

INITIAL PROGRAMMING

HIGH FOOD ALARM

180 °F

180 Blinks

15

Image 16
Contents American Panel Corporation REV. EE-mail service@americanpanel.com USER’S MANUALCONTROLLER FEATURES INSTALLATION OF REMOTE UNITSREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION AT THE SAME LEVELPREPARING AND USING THE OPTIONAL PRINTER MAINTENANCEMAINTENANCE AND CLEANING CLEANING THE CONDENSERINTRODUCTION CONTROLLER FEATURESOPERATING MODES PRINTER OPTIONAL OPERATING CYCLESPC CONNECTION OPTIONAL INSTALLATION OF REMOTE UNITS REQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPSINSTALLATION AT THE SAME LEVEL COMPRESSORINSTALLATION AT DIFFERENT LEVELS CONNECTION PIPING FOR REMOTE CONDENSING UNITSINSTALLATION INSTALLATIONDIMENSIONS WARNINGSVERIFYING CORRECT INSTALLATION ELECTRICAL AND REFRIGERATION SPECIFICATIONSCONNECTION TO THE REMOTE UNIT CONDENSATE DRAINAGE CONNECTIONSTARTING & TESTING THE UNIT SPACES AROUND THE CABINETUSING THE HURRICHILL TECHNOLOGY BLAST CHILLINGSHOCK FREEZING SOFT CHILL CYCLEPANNING PANNING AND LOADINGLOADING CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS KEYBOARD KEYS KEY COMBINATIONSON/OFF & START/STOP PROGRAMMING KEYSc. Enter the default password by pressing, in order, the If the entered password is wrong the display will showPROGRAMMING 1. INITIAL PROGRAMMINGThe low air alarm temperature should be left at The high air alarm temperature should be left atThe high food alarm temperature should be left at The low food alarm temperature should be left at The P.C. baud rate should be left atYES for shock freezers AP24BCF300-3, AP40BCF450-3 NO for blast chillers AP24BC250-3, AP40BC350-3 and go to step r2. PROGRAMMING THE CYCLES AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMINGAUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMING k. To change the temperature, pressthen press p. To change the temperature, pressUV LIGHT CYCLE PARAMETERS PROGRAMMING DEFROST CYCLE PARAMETERS PROGRAMMING HEATED PROBE CYCLE PARAMETERS PROGRAMMINGThe defrost type must be left AIR FLOW aa. PressMANUAL SOFT CYCLE PARAMETERS PROGRAMMING gg. PressThe LED for SOFT will be steady hh. To change the temperature, pressMANUAL HARD CYCLE PARAMETERS PROGRAMMING MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING OPERATION 1. AUTOMATIC MODE - SOFT CHILLalternating with 2. MANUAL MODE - SOFT CHILLalternating 3. HARD CHILL CYCLE 4. SHOCK FREEZE CYCLE 5. UV STERILIZATION CYCLE6. DEFROST CYCLE a. To perform a UV cycle remove all food, then press7. HEATED FOOD PROBE b. Open the doorc. Press the defrost cycle8. PREPARING AND USING THE OPTIONAL PRINTER OTE To stop any cycle before it has finished, press START/STOPd. Enter your password, then press NOTE The optional printer is delivered fully installedPRINTER 9. TO CLEAR DATAMAINTENANCE LOADING A ROLL OF PAPERREMOVING A ROLL OF PAPER OPERATING THE PRINTERCLEANING THE CONDENSER MAINTENANCE AND CLEANINGREPLACING THE RIBBON WITH PAPER IN THE PRINTER WIRING DIAGRAMS CLEANINGCOMPARTMENT DO NOT USE ABRASIVES, SOLVENTSAP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual COMPUTER CONNECTION PART # PARTS LISTDESCRIPTION STANDARD WARRANTY installing contractor. It is not covered by this WarrantyAMERICAN PANEL CORP BLAST CHILLERS / SHOCK FREEZERS ONLYORDERING PRINTER SUPPLIES RIBBON & PAPER