American Panel AP24BC250-3 Manual Mode - Soft Chill, alternating with, The display will show

Page 28

alternating with

AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual

The display will show:

alternating with

alternating with

h.Press the ("START/STOP") button to start the cycle.

READY TO START

PRESS START

03.07.2006		10:28 AM
AIR 1	75°F
		00:00

R / CHICKEN		140°F
Y / ROAST BEEF		143°F
B / CHICKEN		141°F
G / ROAST BEEF		142°F

PRESS START

Blinks

The display will show briefly:

STARTING CYCLE . . .

Then the display will show:

alternating with

03.07.2006		10:28 AM
AIR 1	75°F
		00:00

R / CHICKEN		140°F
Y / ROAST BEEF		143°F
B / CHICKEN		141°F
G / ROAST BEEF		142°F

00:00

Will count up

The AUTOMATIC mode uses both the food probes and air probe temperatures to control the cycle. When all the food temperatures have reached the final setting of 40o F, the unit will automatically go into holding mode and a beep will sound for 5 seconds. The elapsed time and food temperature readouts will blink.

The display will show:		03.07.2006		11:57 AM
The display will show:		AIR 1	34°F
									Blinks
	alternating with			01:29		01:29
				01:29

		R / CHICKEN		40°F				40°F
		Y / ROAST BEEF		40°F	is			alternating
		B / CHICKEN		40°F					with
		G / ROAST BEEF		40°F			Ready

The operator can now end this cycle by pressing the ("START/ STOP") button.

The display will show briefly:

STOPPING CYCLE . . .

Then the display will show:

OPERATING MODE

CHOOSE

OPERATING CYCLE

2. MANUAL MODE - SOFT CHILL

27

Image 28

Contents American Panel Corporation REV. EE-mail service@americanpanel.com USER’S MANUALCONTROLLER FEATURES INSTALLATION OF REMOTE UNITSREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION AT THE SAME LEVELPREPARING AND USING THE OPTIONAL PRINTER MAINTENANCEMAINTENANCE AND CLEANING CLEANING THE CONDENSERINTRODUCTION CONTROLLER FEATURESOPERATING MODES PRINTER OPTIONAL OPERATING CYCLESPC CONNECTION OPTIONAL INSTALLATION OF REMOTE UNITS REQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPSINSTALLATION AT THE SAME LEVEL COMPRESSORINSTALLATION AT DIFFERENT LEVELS CONNECTION PIPING FOR REMOTE CONDENSING UNITSINSTALLATION INSTALLATIONDIMENSIONS WARNINGSVERIFYING CORRECT INSTALLATION ELECTRICAL AND REFRIGERATION SPECIFICATIONSCONNECTION TO THE REMOTE UNIT CONDENSATE DRAINAGE CONNECTIONSTARTING & TESTING THE UNIT SPACES AROUND THE CABINETUSING THE HURRICHILL TECHNOLOGY BLAST CHILLINGSHOCK FREEZING SOFT CHILL CYCLEPANNING PANNING AND LOADINGLOADING CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS KEYBOARD KEYS KEY COMBINATIONSON/OFF & START/STOP PROGRAMMING KEYSc. Enter the default password by pressing, in order, the If the entered password is wrong the display will showPROGRAMMING 1. INITIAL PROGRAMMINGThe low air alarm temperature should be left at The high air alarm temperature should be left atThe high food alarm temperature should be left at The low food alarm temperature should be left at The P.C. baud rate should be left atYES for shock freezers AP24BCF300-3, AP40BCF450-3 NO for blast chillers AP24BC250-3, AP40BC350-3 and go to step r2. PROGRAMMING THE CYCLES AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMINGAUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMING k. To change the temperature, pressthen press p. To change the temperature, pressUV LIGHT CYCLE PARAMETERS PROGRAMMING DEFROST CYCLE PARAMETERS PROGRAMMING HEATED PROBE CYCLE PARAMETERS PROGRAMMINGThe defrost type must be left AIR FLOW aa. PressMANUAL SOFT CYCLE PARAMETERS PROGRAMMING gg. PressThe LED for SOFT will be steady hh. To change the temperature, pressMANUAL HARD CYCLE PARAMETERS PROGRAMMING MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING OPERATION 1. AUTOMATIC MODE - SOFT CHILLalternating with 2. MANUAL MODE - SOFT CHILLalternating 3. HARD CHILL CYCLE 4. SHOCK FREEZE CYCLE 5. UV STERILIZATION CYCLE6. DEFROST CYCLE a. To perform a UV cycle remove all food, then press7. HEATED FOOD PROBE b. Open the doorc. Press the defrost cycle8. PREPARING AND USING THE OPTIONAL PRINTER OTE To stop any cycle before it has finished, press START/STOPd. Enter your password, then press NOTE The optional printer is delivered fully installedPRINTER 9. TO CLEAR DATAMAINTENANCE LOADING A ROLL OF PAPERREMOVING A ROLL OF PAPER OPERATING THE PRINTERCLEANING THE CONDENSER MAINTENANCE AND CLEANINGREPLACING THE RIBBON WITH PAPER IN THE PRINTER WIRING DIAGRAMS CLEANINGCOMPARTMENT DO NOT USE ABRASIVES, SOLVENTSAP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual COMPUTER CONNECTION PART # PARTS LISTDESCRIPTION STANDARD WARRANTY installing contractor. It is not covered by this WarrantyAMERICAN PANEL CORP BLAST CHILLERS / SHOCK FREEZERS ONLYORDERING PRINTER SUPPLIES RIBBON & PAPER