American Panel AP24BC250-3 user manual Automatic Soft Cycle Parameters Programming

Page 19

AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING

AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual

AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING

The LED for "A" will be "ON".

The LED'S for cycles will be blinking.

c.Press . The LED for "SOFT" will be steady "ON".

PARAM. PROGRAMMING

AUTOMATIC MODE

CHOOSE

PROGRAMMING CYCLE

d.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE LOW AIR TEMPERATURE 28 °F

28 Blinks

e.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE HIGH AIR TEMPERATURE 35 °F

35 Blinks

f.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE FOOD TEMPERATURE 40 °F

40 Blinks

g.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE HOLDING LOW TEMP. 35 °F

35 Blinks

h.To change the temperature, press or

then press .

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE HOLDING HIGH TEMP. 42 °F

42 Blinks

The display will show:

PARAM. PROGRAMMING AUTOMATIC SOFT CYCLE

PROGRAMMING COMPLETE

AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING

After about 2 seconds the display will automatically change to:

The LED for "A" will be "ON".

The LED'S for cycles will be blinking.

i.Press the button. The LED for "HARD" will be steady "ON".

PARAM. PROGRAMMING

AUTOMATIC MODE

CHOOSE

PROGRAMMING CYCLE

j. To change the temperature, press or

PARAM. PROGRAMMING AUTOMATIC HARD CYCLE LOW AIR TEMP PART 1

0 °F *

0 Blinks

18

Image 19

Contents USER’S MANUAL American Panel CorporationREV. E E-mail service@americanpanel.comINSTALLATION AT THE SAME LEVEL CONTROLLER FEATURESINSTALLATION OF REMOTE UNITS REQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPSCLEANING THE CONDENSER PREPARING AND USING THE OPTIONAL PRINTERMAINTENANCE MAINTENANCE AND CLEANINGINTRODUCTION CONTROLLER FEATURESOPERATING MODES PRINTER OPTIONAL OPERATING CYCLESPC CONNECTION OPTIONAL COMPRESSOR INSTALLATION OF REMOTE UNITSREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION AT THE SAME LEVELCONNECTION PIPING FOR REMOTE CONDENSING UNITS INSTALLATION AT DIFFERENT LEVELSWARNINGS INSTALLATIONINSTALLATION DIMENSIONSCONDENSATE DRAINAGE CONNECTION VERIFYING CORRECT INSTALLATIONELECTRICAL AND REFRIGERATION SPECIFICATIONS CONNECTION TO THE REMOTE UNITSPACES AROUND THE CABINET STARTING & TESTING THE UNITSOFT CHILL CYCLE USING THE HURRICHILL TECHNOLOGYBLAST CHILLING SHOCK FREEZINGPANNING PANNING AND LOADINGLOADING CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS PROGRAMMING KEYS KEYBOARD KEYSKEY COMBINATIONS ON/OFF & START/STOP1. INITIAL PROGRAMMING c. Enter the default password by pressing, in order, theIf the entered password is wrong the display will show PROGRAMMINGThe low air alarm temperature should be left at The high air alarm temperature should be left atThe high food alarm temperature should be left at NO for blast chillers AP24BC250-3, AP40BC350-3 and go to step r The low food alarm temperature should be left atThe P.C. baud rate should be left at YES for shock freezers AP24BCF300-3, AP40BCF450-32. PROGRAMMING THE CYCLES AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMINGp. To change the temperature, press AUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMINGk. To change the temperature, press then pressUV LIGHT CYCLE PARAMETERS PROGRAMMING aa. Press DEFROST CYCLE PARAMETERS PROGRAMMINGHEATED PROBE CYCLE PARAMETERS PROGRAMMING The defrost type must be left AIR FLOWhh. To change the temperature, press MANUAL SOFT CYCLE PARAMETERS PROGRAMMINGgg. Press The LED for SOFT will be steadyMANUAL HARD CYCLE PARAMETERS PROGRAMMING MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING 1. AUTOMATIC MODE - SOFT CHILL OPERATIONalternating with 2. MANUAL MODE - SOFT CHILLalternating 3. HARD CHILL CYCLE a. To perform a UV cycle remove all food, then press 4. SHOCK FREEZE CYCLE5. UV STERILIZATION CYCLE 6. DEFROST CYCLEdefrost cycle 7. HEATED FOOD PROBEb. Open the door c. Press theOTE To stop any cycle before it has finished, press START/STOP 8. PREPARING AND USING THE OPTIONAL PRINTER9. TO CLEAR DATA d. Enter your password, then pressNOTE The optional printer is delivered fully installed PRINTEROPERATING THE PRINTER MAINTENANCELOADING A ROLL OF PAPER REMOVING A ROLL OF PAPERCLEANING THE CONDENSER MAINTENANCE AND CLEANINGREPLACING THE RIBBON WITH PAPER IN THE PRINTER DO NOT USE ABRASIVES, SOLVENTS WIRING DIAGRAMSCLEANING COMPARTMENTAP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual COMPUTER CONNECTION PART # PARTS LISTDESCRIPTION BLAST CHILLERS / SHOCK FREEZERS ONLY STANDARD WARRANTYinstalling contractor. It is not covered by this Warranty AMERICAN PANEL CORPORDERING PRINTER SUPPLIES RIBBON & PAPER