American Panel AP24BC250-3 Loading A Roll Of Paper, Removing A Roll Of Paper, Maintenance

Page 34
LOADING A ROLL OF PAPER

AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual

LOADING A ROLL OF PAPER

1.Remove the paper cover by pressing on the groove patterns to pop the front edge up. Lift off the cover.

2.Press the rocker switch to the left. The light will go off.

3.Unroll several inches of paper.

4.Cut a straight edge on the paper roll if it is jagged. This will facilitate the entry of the paper into the printer.

5.Slide the paper (with the roll above the paper) through the slot connecting the paper compartment and the printer compartment. It can be slid in about 1/4” before it stops.

6.While holding the paper in place, press the rocker switch to the Paper Feed position and hold it there. The printer will activate and a rubber roller will pull the paper into the printer compartment. Release the switch when an inch of paper has emerged from the top of the printer.

7.Slide the paper through the slot in the printer cover.

8.Push the back of the printer cover down and into place.

9.Press the front of the printer cover down to lock in place.

10.Put the paper spindle into the paper roll and place the roll with the spindle onto the snaps near the back of the printer. Turn the paper roll to take up any slack. Make sure the roll of paper turns freely. If it does not turn freely, the paper will jam and can possibly damage the print mechanism.

REMOVING A ROLL OF PAPER

1.Using the Paper Feed Switch, advance the paper about one inch beyond the paper cutter.

2.Lift the paper roll away from the printer housing and cut the paper feeding to the printer with scissors. Try to make the cut as square as possible to help the next time you reload the paper.

3.Pull the remaining paper through the printer mechanism. Be sure to pull the paper from the top (paper cutter side).

WARNING: Pulling the paper out from the back of the printer will damage the print mechanism.

OPERATING THE PRINTER

The Paper Feed switch on the printer is a rocker type switch. Push the left side of the rocker switch to toggle the printer ON or OFF. A red light will go on when the printer switch is ON. Push the right side of the switch to advance the paper.

MAINTENANCE

When printing becomes difficult to see, replace the ribbon in your printer with an Epson HX-20 cartridge ribbon.

If your printer is used infrequently, the print impression may become weak because the ribbon dried out. In that case, advance the ribbon to a new section by holding down the Paper Feed switch for several seconds.

REPLACING THE RIBBON (NO PAPER IN THE PRINTER)

1. Turn the printer OFF.

33

Image 34
Contents E-mail service@americanpanel.com American Panel CorporationREV. E USER’S MANUALREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS CONTROLLER FEATURESINSTALLATION OF REMOTE UNITS INSTALLATION AT THE SAME LEVELMAINTENANCE AND CLEANING PREPARING AND USING THE OPTIONAL PRINTERMAINTENANCE CLEANING THE CONDENSERINTRODUCTION CONTROLLER FEATURESOPERATING MODES PRINTER OPTIONAL OPERATING CYCLESPC CONNECTION OPTIONAL INSTALLATION AT THE SAME LEVEL INSTALLATION OF REMOTE UNITSREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS COMPRESSORINSTALLATION AT DIFFERENT LEVELS CONNECTION PIPING FOR REMOTE CONDENSING UNITSDIMENSIONS INSTALLATIONINSTALLATION WARNINGSCONNECTION TO THE REMOTE UNIT VERIFYING CORRECT INSTALLATIONELECTRICAL AND REFRIGERATION SPECIFICATIONS CONDENSATE DRAINAGE CONNECTIONSTARTING & TESTING THE UNIT SPACES AROUND THE CABINETSHOCK FREEZING USING THE HURRICHILL TECHNOLOGYBLAST CHILLING SOFT CHILL CYCLEPANNING PANNING AND LOADINGLOADING CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS ON/OFF & START/STOP KEYBOARD KEYSKEY COMBINATIONS PROGRAMMING KEYSPROGRAMMING c. Enter the default password by pressing, in order, theIf the entered password is wrong the display will show 1. INITIAL PROGRAMMINGThe low air alarm temperature should be left at The high air alarm temperature should be left atThe high food alarm temperature should be left at YES for shock freezers AP24BCF300-3, AP40BCF450-3 The low food alarm temperature should be left atThe P.C. baud rate should be left at NO for blast chillers AP24BC250-3, AP40BC350-3 and go to step r2. PROGRAMMING THE CYCLES AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMINGthen press AUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMINGk. To change the temperature, press p. To change the temperature, pressUV LIGHT CYCLE PARAMETERS PROGRAMMING The defrost type must be left AIR FLOW DEFROST CYCLE PARAMETERS PROGRAMMINGHEATED PROBE CYCLE PARAMETERS PROGRAMMING aa. PressThe LED for SOFT will be steady MANUAL SOFT CYCLE PARAMETERS PROGRAMMINGgg. Press hh. To change the temperature, pressMANUAL HARD CYCLE PARAMETERS PROGRAMMING MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING OPERATION 1. AUTOMATIC MODE - SOFT CHILLalternating with 2. MANUAL MODE - SOFT CHILLalternating 3. HARD CHILL CYCLE 6. DEFROST CYCLE 4. SHOCK FREEZE CYCLE5. UV STERILIZATION CYCLE a. To perform a UV cycle remove all food, then pressc. Press the 7. HEATED FOOD PROBEb. Open the door defrost cycle8. PREPARING AND USING THE OPTIONAL PRINTER OTE To stop any cycle before it has finished, press START/STOPPRINTER d. Enter your password, then pressNOTE The optional printer is delivered fully installed 9. TO CLEAR DATAREMOVING A ROLL OF PAPER MAINTENANCELOADING A ROLL OF PAPER OPERATING THE PRINTERCLEANING THE CONDENSER MAINTENANCE AND CLEANINGREPLACING THE RIBBON WITH PAPER IN THE PRINTER COMPARTMENT WIRING DIAGRAMSCLEANING DO NOT USE ABRASIVES, SOLVENTSAP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual COMPUTER CONNECTION PART # PARTS LISTDESCRIPTION AMERICAN PANEL CORP STANDARD WARRANTYinstalling contractor. It is not covered by this Warranty BLAST CHILLERS / SHOCK FREEZERS ONLYORDERING PRINTER SUPPLIES RIBBON & PAPER