American Panel AP24BC250-3 user manual Automatic Shock Cycle Parameters Programming, then press

Page 20
k. To change the temperature, press

AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual

then press then press.

*0o F for shock freezers (AP24BCF300-3, AP40BCF450-3) 10o F for blast chillers (AP24BC250-3, AP40BC350-3)

 

 

 

PARAM. PROGRAMMING

 

k. To change the temperature, press

or

AUTOMATIC HARD CYCLE

 

 

 

 

HIGH AIR TEMP PART 1

10 Blinks

 

 

 

10 °F **

then press

.

 

 

 

**10o F for shock freezers (AP24BCF300-3, AP40BCF450-3) 20o F for blast chillers (AP24BC250-3, AP40BC350-3)

l.To change the temperature, press p. To change the temperature, press or q. To change the temperature, press

then press The display will show:.

PARAM. PROGRAMMING AUTOMATIC HARD CYCLE BREAKING TEMP

60 °F

60 Blinks

m. To change the temperature, press AUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMING or Manual background

then press Manual background.

PARAM. PROGRAMMING AUTOMATIC HARD CYCLE LOW AIR TEMP PART 2 28 °F

28 Blinks

n.To change the temperature, press Manual background or Manual background

then press Manual background.

PARAM. PROGRAMMING AUTOMATIC HARD CYCLE HIGH AIR TEMP PART 2

35 °F

35 Blinks

o.To change the temperature, press Manual background or Manual background

then press Manual background.

PARAM. PROGRAMMING AUTOMATIC HARD CYCLE HARD FOOD TEMP.

40 °F

40 Blinks

 

 

 

PARAM. PROGRAMMING

 

p. To change the temperature, press

or

AUTOMATIC HARD CYCLE

 

 

 

 

HOLDING LOW TEMP.

35 Blinks

 

 

 

35 °F

then press

.

 

 

 

 

 

 

 

q. To change the temperature, press

or

PARAM. PROGRAMMING

 

 

 

 

AUTOMATIC HARD CYCLE

42 Blinks

 

 

 

HOLDING HIGH TEMP.

then press

.

 

42 °F

 

 

 

 

 

 

 

 

 

The display will show:

 

PARAM. PROGRAMMING

 

 

AUTOMATIC HARD CYCLE

 

 

 

 

PROGRAMMING COMPLETE

 

 

 

 

 

 

AUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMING

19

Page 19 Page 21
Image 20
Page 19 Page 21
Contents American Panel Corporation REV. EE-mail service@americanpanel.com USER’S MANUALCONTROLLER FEATURES INSTALLATION OF REMOTE UNITSREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION AT THE SAME LEVELPREPARING AND USING THE OPTIONAL PRINTER MAINTENANCEMAINTENANCE AND CLEANING CLEANING THE CONDENSEROPERATING MODES CONTROLLER FEATURESINTRODUCTION PC CONNECTION OPTIONAL OPERATING CYCLESPRINTER OPTIONAL INSTALLATION OF REMOTE UNITS REQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPSINSTALLATION AT THE SAME LEVEL COMPRESSORINSTALLATION AT DIFFERENT LEVELS CONNECTION PIPING FOR REMOTE CONDENSING UNITSINSTALLATION INSTALLATIONDIMENSIONS WARNINGSVERIFYING CORRECT INSTALLATION ELECTRICAL AND REFRIGERATION SPECIFICATIONSCONNECTION TO THE REMOTE UNIT CONDENSATE DRAINAGE CONNECTIONSTARTING & TESTING THE UNIT SPACES AROUND THE CABINETUSING THE HURRICHILL TECHNOLOGY BLAST CHILLINGSHOCK FREEZING SOFT CHILL CYCLELOADING PANNING AND LOADINGPANNING CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS KEYBOARD KEYS KEY COMBINATIONSON/OFF & START/STOP PROGRAMMING KEYSc. Enter the default password by pressing, in order, the If the entered password is wrong the display will showPROGRAMMING 1. INITIAL PROGRAMMINGThe high food alarm temperature should be left at The high air alarm temperature should be left atThe low air alarm temperature should be left at The low food alarm temperature should be left at The P.C. baud rate should be left atYES for shock freezers AP24BCF300-3, AP40BCF450-3 NO for blast chillers AP24BC250-3, AP40BC350-3 and go to step r2. PROGRAMMING THE CYCLES AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMING AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMINGAUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMING k. To change the temperature, pressthen press p. To change the temperature, pressUV LIGHT CYCLE PARAMETERS PROGRAMMING DEFROST CYCLE PARAMETERS PROGRAMMING HEATED PROBE CYCLE PARAMETERS PROGRAMMINGThe defrost type must be left AIR FLOW aa. PressMANUAL SOFT CYCLE PARAMETERS PROGRAMMING gg. PressThe LED for SOFT will be steady hh. To change the temperature, pressMANUAL HARD CYCLE PARAMETERS PROGRAMMING MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING OPERATION 1. AUTOMATIC MODE - SOFT CHILLalternating 2. MANUAL MODE - SOFT CHILLalternating with 3. HARD CHILL CYCLE 4. SHOCK FREEZE CYCLE 5. UV STERILIZATION CYCLE6. DEFROST CYCLE a. To perform a UV cycle remove all food, then press7. HEATED FOOD PROBE b. Open the doorc. Press the defrost cycle8. PREPARING AND USING THE OPTIONAL PRINTER OTE To stop any cycle before it has finished, press START/STOPd. Enter your password, then press NOTE The optional printer is delivered fully installedPRINTER 9. TO CLEAR DATAMAINTENANCE LOADING A ROLL OF PAPERREMOVING A ROLL OF PAPER OPERATING THE PRINTERREPLACING THE RIBBON WITH PAPER IN THE PRINTER MAINTENANCE AND CLEANINGCLEANING THE CONDENSER WIRING DIAGRAMS CLEANINGCOMPARTMENT DO NOT USE ABRASIVES, SOLVENTSAP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual COMPUTER CONNECTION DESCRIPTION PARTS LISTPART # STANDARD WARRANTY installing contractor. It is not covered by this WarrantyAMERICAN PANEL CORP BLAST CHILLERS / SHOCK FREEZERS ONLYORDERING PRINTER SUPPLIES RIBBON & PAPER
Top Page Image Contents