American Panel AP24BC250-3 user manual Hard Chill Cycle, The display will show, alternating with

Page 29

3. HARD CHILL CYCLE

AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual

F INSTEAD OF AUTOMATIC you wish to select a MANUAL cycle, perform steps 1.a, 1.b, 1.c, 1.d,

1.e, 1f and 1.g (above), except in step 1.c press button instead of button . The LED for "MANUAL" will then be steady "ON". The readouts in those steps will be the same as before.

NOTE: Cycle time can be changed only in Cycle Programming mode. To change the programmed cycle time for any cycle see the instructions on Pages 17 to 25.

h. Press the ("START/STOP") button to start the cycle.

The display will show briefly:

STARTING CYCLE . . .

Then the display will show:

alternating with

03.07.2006		10:41 AM
AIR 1	75°F
		01:29

R / CHICKEN		140°F
Y / ROAST BEEF		143°F
B / CHICKEN		141°F
G / ROAST BEEF		142°F

01:29

Will count down

The MANUAL mode uses time and the air probe temperature to control the cycle.

The default total time for a soft cycle is 90 minutes. After the 90 minutes the unit will automatically go into holding mode.

The display will show:		03.07.2006		10:41 AM
The display will show:		AIR 1	34°F
	alternating with			00:00
	alternating with
		R / CHICKEN		40°F
		Y / ROAST BEEF		40°F
		B / CHICKEN		40°F
		G / ROAST BEEF		40°F

00:00 Blinks

The operator can now end this cycle by pressing ("START/ STOP").

The display will show briefly:

STOPPING CYCLE . . .

Then the display will show:

OPERATING MODE

CHOOSE

OPERATING CYCLE

3. HARD CHILL CYCLE

28

Image 29

Contents REV. E American Panel CorporationE-mail service@americanpanel.com USER’S MANUALINSTALLATION OF REMOTE UNITS CONTROLLER FEATURESREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION AT THE SAME LEVELMAINTENANCE PREPARING AND USING THE OPTIONAL PRINTERMAINTENANCE AND CLEANING CLEANING THE CONDENSEROPERATING MODES CONTROLLER FEATURESINTRODUCTION PC CONNECTION OPTIONAL OPERATING CYCLESPRINTER OPTIONAL REQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION OF REMOTE UNITSINSTALLATION AT THE SAME LEVEL COMPRESSORCONNECTION PIPING FOR REMOTE CONDENSING UNITS INSTALLATION AT DIFFERENT LEVELSINSTALLATION INSTALLATIONDIMENSIONS WARNINGSELECTRICAL AND REFRIGERATION SPECIFICATIONS VERIFYING CORRECT INSTALLATIONCONNECTION TO THE REMOTE UNIT CONDENSATE DRAINAGE CONNECTIONSPACES AROUND THE CABINET STARTING & TESTING THE UNITBLAST CHILLING USING THE HURRICHILL TECHNOLOGYSHOCK FREEZING SOFT CHILL CYCLELOADING PANNING AND LOADINGPANNING CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS KEY COMBINATIONS KEYBOARD KEYSON/OFF & START/STOP PROGRAMMING KEYSIf the entered password is wrong the display will show c. Enter the default password by pressing, in order, thePROGRAMMING 1. INITIAL PROGRAMMINGThe high food alarm temperature should be left at The high air alarm temperature should be left atThe low air alarm temperature should be left at The P.C. baud rate should be left at The low food alarm temperature should be left atYES for shock freezers AP24BCF300-3, AP40BCF450-3 NO for blast chillers AP24BC250-3, AP40BC350-3 and go to step r2. PROGRAMMING THE CYCLES AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMINGk. To change the temperature, press AUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMINGthen press p. To change the temperature, pressUV LIGHT CYCLE PARAMETERS PROGRAMMING HEATED PROBE CYCLE PARAMETERS PROGRAMMING DEFROST CYCLE PARAMETERS PROGRAMMINGThe defrost type must be left AIR FLOW aa. Pressgg. Press MANUAL SOFT CYCLE PARAMETERS PROGRAMMINGThe LED for SOFT will be steady hh. To change the temperature, pressMANUAL HARD CYCLE PARAMETERS PROGRAMMING MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING 1. AUTOMATIC MODE - SOFT CHILL OPERATIONalternating 2. MANUAL MODE - SOFT CHILLalternating with 3. HARD CHILL CYCLE 5. UV STERILIZATION CYCLE 4. SHOCK FREEZE CYCLE6. DEFROST CYCLE a. To perform a UV cycle remove all food, then pressb. Open the door 7. HEATED FOOD PROBEc. Press the defrost cycleOTE To stop any cycle before it has finished, press START/STOP 8. PREPARING AND USING THE OPTIONAL PRINTERNOTE The optional printer is delivered fully installed d. Enter your password, then pressPRINTER 9. TO CLEAR DATALOADING A ROLL OF PAPER MAINTENANCEREMOVING A ROLL OF PAPER OPERATING THE PRINTERREPLACING THE RIBBON WITH PAPER IN THE PRINTER MAINTENANCE AND CLEANINGCLEANING THE CONDENSER CLEANING WIRING DIAGRAMSCOMPARTMENT DO NOT USE ABRASIVES, SOLVENTSAP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual COMPUTER CONNECTION DESCRIPTION PARTS LISTPART # installing contractor. It is not covered by this Warranty STANDARD WARRANTYAMERICAN PANEL CORP BLAST CHILLERS / SHOCK FREEZERS ONLYORDERING PRINTER SUPPLIES RIBBON & PAPER