American Panel user manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual

Page 37

Manual background

AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual

36

Image 37

Contents REV. E American Panel CorporationE-mail service@americanpanel.com USER’S MANUALINSTALLATION OF REMOTE UNITS CONTROLLER FEATURESREQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION AT THE SAME LEVELMAINTENANCE PREPARING AND USING THE OPTIONAL PRINTERMAINTENANCE AND CLEANING CLEANING THE CONDENSERINTRODUCTION CONTROLLER FEATURESOPERATING MODES PRINTER OPTIONAL OPERATING CYCLESPC CONNECTION OPTIONAL REQUIREMENTS TO BE MET DURING INSTALLATION 8 STEPS INSTALLATION OF REMOTE UNITSINSTALLATION AT THE SAME LEVEL COMPRESSORCONNECTION PIPING FOR REMOTE CONDENSING UNITS INSTALLATION AT DIFFERENT LEVELSINSTALLATION INSTALLATIONDIMENSIONS WARNINGSELECTRICAL AND REFRIGERATION SPECIFICATIONS VERIFYING CORRECT INSTALLATIONCONNECTION TO THE REMOTE UNIT CONDENSATE DRAINAGE CONNECTIONSPACES AROUND THE CABINET STARTING & TESTING THE UNITBLAST CHILLING USING THE HURRICHILL TECHNOLOGYSHOCK FREEZING SOFT CHILL CYCLEPANNING PANNING AND LOADINGLOADING CONTROL PANEL FOR MODELS AP24 & AP40 BLAST CHILLERS / SHOCK FREEZERS KEY COMBINATIONS KEYBOARD KEYSON/OFF & START/STOP PROGRAMMING KEYSIf the entered password is wrong the display will show c. Enter the default password by pressing, in order, thePROGRAMMING 1. INITIAL PROGRAMMINGThe low air alarm temperature should be left at The high air alarm temperature should be left atThe high food alarm temperature should be left at The P.C. baud rate should be left at The low food alarm temperature should be left atYES for shock freezers AP24BCF300-3, AP40BCF450-3 NO for blast chillers AP24BC250-3, AP40BC350-3 and go to step r2. PROGRAMMING THE CYCLES AUTOMATIC HARD CYCLE PARAMETERS PROGRAMMING AUTOMATIC SOFT CYCLE PARAMETERS PROGRAMMINGk. To change the temperature, press AUTOMATIC SHOCK CYCLE PARAMETERS PROGRAMMINGthen press p. To change the temperature, pressUV LIGHT CYCLE PARAMETERS PROGRAMMING HEATED PROBE CYCLE PARAMETERS PROGRAMMING DEFROST CYCLE PARAMETERS PROGRAMMINGThe defrost type must be left AIR FLOW aa. Pressgg. Press MANUAL SOFT CYCLE PARAMETERS PROGRAMMINGThe LED for SOFT will be steady hh. To change the temperature, pressMANUAL HARD CYCLE PARAMETERS PROGRAMMING MANUAL SHOCK CYCLE PARAMETERS PROGRAMMING 3. RECIPE NAME PROGRAMMING 1. AUTOMATIC MODE - SOFT CHILL OPERATIONalternating with 2. MANUAL MODE - SOFT CHILLalternating 3. HARD CHILL CYCLE 5. UV STERILIZATION CYCLE 4. SHOCK FREEZE CYCLE6. DEFROST CYCLE a. To perform a UV cycle remove all food, then pressb. Open the door 7. HEATED FOOD PROBEc. Press the defrost cycleOTE To stop any cycle before it has finished, press START/STOP 8. PREPARING AND USING THE OPTIONAL PRINTERNOTE The optional printer is delivered fully installed d. Enter your password, then pressPRINTER 9. TO CLEAR DATALOADING A ROLL OF PAPER MAINTENANCEREMOVING A ROLL OF PAPER OPERATING THE PRINTERCLEANING THE CONDENSER MAINTENANCE AND CLEANINGREPLACING THE RIBBON WITH PAPER IN THE PRINTER CLEANING WIRING DIAGRAMSCOMPARTMENT DO NOT USE ABRASIVES, SOLVENTSAP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual AP24BC250-3, AP24BCF300-3, AP40BC350-3, AP40BCF450-3 Manual COMPUTER CONNECTION PART # PARTS LISTDESCRIPTION installing contractor. It is not covered by this Warranty STANDARD WARRANTYAMERICAN PANEL CORP BLAST CHILLERS / SHOCK FREEZERS ONLYORDERING PRINTER SUPPLIES RIBBON & PAPER