Sonance C4630 SE instruction manual Problem

Page 55

C4630 SE HOME AUDIO SYSTEM

SERIAL CONTROL

Problem

No RS-232 communication with an external device

Solution

a)Is the external device ON?

b)Is the external device connected with the proper RS-232 cable? Check the configuration of the external device’s RS-232 port. The C4630 SE’s RS-232 pin configuration is:

Pin 2 = Receive (Rx), pin 3 = Transmit (Tx), Pin 5 = Ground (Gnd) .

c)Are the ‘baud rate’ and ‘format’ of the external device properly configured? See page 40.

d)Is the external device properly configured to send/receive?

e)Are the ASCII text serial commands programmed in Sonance Control Manager correct? See page 40.

f)If using Hex commands, be sure the Macro Editor screen’s HEX MODE button is pressed before inputting the Hex command (see page 40).

g)If the C4630 SE is being serial-controlled by the external device, make sure that all C4630 SE macros are purged of all RS-232 commands (see page 50).

PROGRAM MANAGER

Problem

The USB connection gives a Windows error: DEVICE NOT DETECTED

Solution

a)Disconnect and re-connect the USB cable from the C4630 SE and/or the computer.

b)Re-install the USB driver in the computer.

c)Confirm that you have made the proper computer Com Port selection and connection.

d)Unplug the USB cable from the C4630 SE, select DOWNLOAD TO DEVICE on the Sonance Control Manager and then re-connect the USB cable to the C4630 SE.

55

Page 54 Page 56
Image 55
Page 54 Page 56
Contents C4630 SE Page Ance to Rain or MOISTURE. Important Safety InformationTable of Contents C4630 SE Home Audio System Control C4630 SE FeaturesIntroduction AudioPlacement Box ContentsUnpacking Control Considerations System OverviewShelf-Mounting Rack-MountingC4630 SE Home Audio System Rear Panel C4630 SE Front Rear PanelsAudio Source Connections Connecting the C4630 SEPower Connections Replacing the AC FuseSpeaker Connections Use Good Speaker WireWiring the Speaker Connectors Source Output ConnectionsZone Line Output Connections Line Output Fixed/Variable SwitchConnecting a High-Power Amplifier in a Zone Using a Multi-Channel Amplifier for Sub-Zone ExpansionC4630 SE Using a High-Power Amplifier in a ZoneTo connect to the IR Link jacks of the Secondary C4630 SEs When using three or more C4630 SE Controllers, use miniIR Connections see Figure Plug Y-adaptors on the IR Link jack on the Primary C4630 SEControl Input/ Output Sync Connections Wiring the Control ConnectionsControl Out Terminal Sync ConnectionsRS-232 RS-232 Terminal Pins Connector SidePaging Connections see Figure RS-232 Connection see FigureC4630 SE Main Keypad see Figure C4630 SE Keypad ControllersC4630 SE Main and Numeric Keypads Main Keypad IR Receiver Holster Installing an IR Receiver into the KeypadC4630 SE Numeric Keypad see , on Keypad LocationTo the Keypad Connecting the IR ReceiverKeypad Backlighting Jumper C4630 SE Keypad ConnectionsMounting the C4630 SE Keypads External Keypad Power see FigureKeypad Ribbon Cable Insert Tool Changing the Main Keypad Source ButtonsInto Openings C4630 SE Out-Of-The-Box Functions Optional C4630 SE IR Remote ControlSonance Control Manager Software Front Panel Controls and IndicatorsALL OFF Switch Installing the Sonance Control Manager SoftwareUpgrading Sonance Control Manager Software Transferring System Information to the C4630 SETo transfer programming to the C4630 SE Updating the Sonance Control Manager Software and FirmwareUpgrading the C4630 SE Firmware Upgrade Firmware Warning ScreenDevice Screen Creating a New C4630 SE SystemRenaming C4630 SEs in a System with Multiple Units To cor rect for too low or too high a level Feedback , etc Setting Up a ZoneRear-Panel BBE ON/OFF Switches Setting Up SourcesBBE Sound Enhancement Device Screen Figure Programming C4630 SE Keypad MacrosGeneral Macro Programming Notes Fi g u re 4 2 Z o n e 1 P ro g r a m m i n g S c re e n Building MacrosMacro Editor Screen Figure Macro Command TypesCommand From Library IR Commands Adding an IR Command to a MacroDragging Commands into the Macro Window Macro Editor Screen with IR Command Library SelectedProgrammed IR Output Port Selector Modifying the IR Library IR Library ManagerIR Library Manager Edit Tab Editing IR Commands in the User IR LibraryReady to Align Remote and IR Learner Adding Function Names to the Function ListWaveform View Tab Internal CommandsHex View Tab Status Test Time DelayInternal Command Window Time Delay Macro WindowRS-232 Macro Editor Window with an RS-232 command string RS-232 Command Outbound Serial ControlRS-232 Macro Window Repeat Steps Stop MacroC4630 SE Inbound Serial Protocol fixed Drag Commands Into BracketControlling the C4630 SE via RS-232 Inbound Serial Control Toggle IR CodeC4630 SE Inbound Serial Commands C4630 SE Status Queries Inbound Serial Control of C4630 SEs in Multi-Unit SystemsSerial Commands Simulate Button Press Commands in Multi-Unit SystemsPowering K2 Keypads Wiring K2 and K1 Keypad ConnectionsC4630 SE Extra Command Macros Expanded Control FeaturesProgramming a K2 Button to Trigger a C4630 SE Extra Command Triggering C4630 SE Extra Command Macros From the K1 and K2Generating a System Configuration Report Getting System Configuration InformationSystem Configuration Report Showing RS-232 Macro Commands Finding RS-232 Commands in MacrosAudio Performance SpecificationsProblem Solution TroubleshootingAudio Infrared Control Problem Important Freight collect shipments will be refused Technical Assistance and ServiceExclusions and Limitations Limited Warranty Coverage U.S.A. OnlySystem Notes Page 33-4119 07/07
Top Page Image Contents