Sonance C4630 SE Front Panel Controls and Indicators, Sonance Control Manager Software

Page 24

C4630 SE HOME AUDIO SYSTEM

Front Panel Controls and Indicators

(see Figures 25 & 26)

ALL OFF Switch

Pressing the front-panel ALL OFF button will turn all zones OFF. If all zones are already OFF, pressing the ALL OFF switch will have no effect.

•If the system has multiple C4630 SEs daisy-chained via their SYNC Connections (see page 16), pressing the ALL OFF switch on any unit will turn OFF all zones being run by all connected units.

NOTE: After pressing the AL L OF F button wait at least 5 seconds for the microprocessor to reset before turning the unit ON again.

AC ON LED

The AC ON LED illuminates blue as long as the C4630 SE’s power cord is plugged-into a live outlet.

ACTIVE LED

The ACTIVE LED illuminates green whenever any zone run by that C4630 SE is ON.

ZONE STATUS LEDs

ALL OFF

ACTIVE

A.C. ON

Figure 25: Front-Panel ALL OFF Switch,

ACTIVE and AC ON LEDs

ZONE 1

ZONE 2

ZONE 3

ZONE 4

ZONE 5

ZONE 6

Figure 26:

Front-Panel ZONE STATUS LEDs

A zone’s ZONE STATUS LED will illuminate green whenever that zone is ON and will extinguish when the zone is OFF.

Sonance Control Manager Software

The C4630 SE comes with a CD-ROM containing the Sonance Control Manager programming software that lets you program all of the C4630 SE’s operational and sonic parameters. In addition to adjusting each zone’s sonic performance you can also program the buttons on keypad controllers to perform individual functions and to combine literally dozens of different functions into macros that can be triggered by a single keypad button push.

NOTE: In addition to programming the C4630 SE, the Sonance Control Manager sof tware can also be used to program the DAB1. DAB1 programming is explained in another document .

Installing the Sonance Control Manager Software

1.Place the included SONANCE CONTROL MANAGER CD-ROM in your computer’s CD drive.

2.The installer will automatically launch. Follow the instructions to install the program. If the installer does not automatically launch:

1.Go to your computer’s START menu and select RUN.

2.Use the BROWSE function to navigate to the SONANCE CONTROL MANAGER CD.

3.Double-click on INSTALLER.EXE and follow the instructions to install the program.

Sonance Control Manager is compatible with these Windows operating systems:

Windows 2000 series

Windows XP Home

Windows XP Professional

Sonance Control Manager is NOT compatible with any Apple/MacIntosh operating system.

24

Page 23 Page 25
Image 24
Page 23 Page 25
Contents C4630 SE Page Important Safety Information Ance to Rain or MOISTURE.Table of Contents C4630 SE Home Audio System C4630 SE Features IntroductionAudio ControlBox Contents PlacementUnpacking System Overview Shelf-MountingRack-Mounting Control ConsiderationsC4630 SE Home Audio System C4630 SE Front Rear Panels Rear PanelConnecting the C4630 SE Power ConnectionsReplacing the AC Fuse Audio Source ConnectionsUse Good Speaker Wire Wiring the Speaker ConnectorsSource Output Connections Speaker ConnectionsLine Output Fixed/Variable Switch Connecting a High-Power Amplifier in a ZoneUsing a Multi-Channel Amplifier for Sub-Zone Expansion Zone Line Output ConnectionsUsing a High-Power Amplifier in a Zone C4630 SEWhen using three or more C4630 SE Controllers, use mini IR Connections see FigurePlug Y-adaptors on the IR Link jack on the Primary C4630 SE To connect to the IR Link jacks of the Secondary C4630 SEsWiring the Control Connections Control Out TerminalSync Connections Control Input/ Output Sync ConnectionsRS-232 Terminal Pins Connector Side Paging Connections see FigureRS-232 Connection see Figure RS-232C4630 SE Keypad Controllers C4630 SE Main Keypad see FigureC4630 SE Main and Numeric Keypads Installing an IR Receiver into the Keypad C4630 SE Numeric Keypad see , onKeypad Location Main Keypad IR Receiver HolsterConnecting the IR Receiver Keypad Backlighting JumperC4630 SE Keypad Connections To the KeypadExternal Keypad Power see Figure Mounting the C4630 SE KeypadsKeypad Ribbon Cable Changing the Main Keypad Source Buttons Insert ToolInto Openings Optional C4630 SE IR Remote Control C4630 SE Out-Of-The-Box FunctionsFront Panel Controls and Indicators ALL OFF SwitchInstalling the Sonance Control Manager Software Sonance Control Manager SoftwareTransferring System Information to the C4630 SE To transfer programming to the C4630 SEUpdating the Sonance Control Manager Software and Firmware Upgrading Sonance Control Manager SoftwareUpgrade Firmware Warning Screen Upgrading the C4630 SE FirmwareCreating a New C4630 SE System Device ScreenRenaming C4630 SEs in a System with Multiple Units Setting Up a Zone To cor rect for too low or too high a level Feedback , etcSetting Up Sources Rear-Panel BBE ON/OFF SwitchesBBE Sound Enhancement Programming C4630 SE Keypad Macros Device Screen FigureGeneral Macro Programming Notes Building Macros Fi g u re 4 2 Z o n e 1 P ro g r a m m i n g S c re e nMacro Command Types Command From Library IR CommandsAdding an IR Command to a Macro Macro Editor Screen FigureMacro Editor Screen with IR Command Library Selected Dragging Commands into the Macro WindowProgrammed IR Output Port Selector IR Library Manager Modifying the IR LibraryEditing IR Commands in the User IR Library IR Library Manager Edit TabAdding Function Names to the Function List Ready to Align Remote and IR LearnerInternal Commands Waveform View TabHex View Tab Time Delay Internal Command WindowTime Delay Macro Window Status TestRS-232 Command Outbound Serial Control RS-232 Macro Editor Window with an RS-232 command stringRS-232 Macro Window Stop Macro Repeat StepsDrag Commands Into Bracket Controlling the C4630 SE via RS-232 Inbound Serial ControlToggle IR Code C4630 SE Inbound Serial Protocol fixedC4630 SE Inbound Serial Commands Inbound Serial Control of C4630 SEs in Multi-Unit Systems C4630 SE Status QueriesSimulate Button Press Commands in Multi-Unit Systems Serial CommandsWiring K2 and K1 Keypad Connections Powering K2 KeypadsExpanded Control Features C4630 SE Extra Command MacrosTriggering C4630 SE Extra Command Macros From the K1 and K2 Programming a K2 Button to Trigger a C4630 SE Extra CommandGetting System Configuration Information Generating a System Configuration ReportFinding RS-232 Commands in Macros System Configuration Report Showing RS-232 Macro CommandsSpecifications Audio PerformanceTroubleshooting Problem SolutionAudio Infrared Control Problem Technical Assistance and Service Important Freight collect shipments will be refusedLimited Warranty Coverage U.S.A. Only Exclusions and LimitationsSystem Notes Page 33-4119 07/07
Top Page Image Contents