Sonance C4630 SE Limited Warranty Coverage U.S.A. Only, Exclusions and Limitations

Page 57

C4630 SE HOME AUDIO SYSTEM

Limited Warranty Coverage (U.S.A. Only)

Sonance warrants to the original retail purchaser only that this Sonance product will be free from defects in materials and workmanship for a period of five (5) years, provided the product was purchased from a Sonance Authorized Dealer.

Defective products must be shipped, together with proof of purchase, prepaid insured to the Authorized Sonance Dealer from whom they were purchased, or to the Sonance factory at the address listed on this instruction manual. Freight collect shipments will be refused. It is preferable to ship this product in the original shipping container to lessen the chance of transit damage. In any case, the risk or loss or damage in transit is to be borne by the purchaser. If, upon examination at the factory or Authorized Sonance Dealer, it is determined that the unit was defective in materials or workmanship at any time during this warranty period, Sonance or the Authorized Sonance Dealer will, at its option, repair or replace this product at no additional charge, except as set forth below.

If this model is no longer available and can not be repaired effectively, Sonance, at is sole option, may replace the unit with a current model of equal or greater value. In some cases where a new model is substituted, a modification to the mounting surface may be required. If mounting surface modification is required, Sonance assumes no responsibility or lia- bility for such modification. All replaced parts and product become the property of Sonance. Products replaced or repaired under this warranty will be returned to the original retail purchaser, within a reasonable time, freight prepaid.

This Warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, or service, repair or modification of the product which has not been authorized or approved by Sonance. This Warranty also excludes normal cosmetic deterioration caused by environmental conditions. This Warranty is in lieu of all other expressed warranties. If the product is defective in materials or workmanship as warranted above, the purchaser’s sole remedy shall be repair or replacement as provided above. In no event will Sonance be liable for any incidental or conse- quential damages arising out of the use or inability to use the product, even if Sonance or a Authorized Sonance Dealer has been advised of the possibility of such damages, or for any claim by any other party.

Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply. All implied warranties on the product are limited to the duration of this expressed Warranty. Some states do not allow limitation on the length of an implied warranty. If the original retail purchaser resides in such a state, this limitation does not apply.

EXCLUSIONS AND LIMITATIONS

The warranty set forth above is in lieu of all other warranties, express or implied, of merchantability, fitness for a partic- ular purpose, or otherwise. The warranty is limited to Sonance products registered herein and specifically excludes any damage to loudspeakers and other allied or associated equipment which may result for any reason from use with this prod- uct. Sonance shall, in no event, be liable for incidental or consequential damages arising from any breach of this warran- ty or otherwise. This warranty gives you specific legal rights, and you may have other rights which vary from state to state.

57

Image 57
Contents C4630 SE Page Ance to Rain or MOISTURE. Important Safety InformationTable of Contents C4630 SE Home Audio System Introduction C4630 SE FeaturesAudio ControlBox Contents PlacementUnpacking Shelf-Mounting System OverviewRack-Mounting Control ConsiderationsC4630 SE Home Audio System Rear Panel C4630 SE Front Rear PanelsPower Connections Connecting the C4630 SEReplacing the AC Fuse Audio Source ConnectionsWiring the Speaker Connectors Use Good Speaker WireSource Output Connections Speaker ConnectionsConnecting a High-Power Amplifier in a Zone Line Output Fixed/Variable SwitchUsing a Multi-Channel Amplifier for Sub-Zone Expansion Zone Line Output ConnectionsC4630 SE Using a High-Power Amplifier in a ZoneIR Connections see Figure When using three or more C4630 SE Controllers, use miniPlug Y-adaptors on the IR Link jack on the Primary C4630 SE To connect to the IR Link jacks of the Secondary C4630 SEsControl Out Terminal Wiring the Control ConnectionsSync Connections Control Input/ Output Sync ConnectionsPaging Connections see Figure RS-232 Terminal Pins Connector SideRS-232 Connection see Figure RS-232C4630 SE Keypad Controllers C4630 SE Main Keypad see FigureC4630 SE Main and Numeric Keypads C4630 SE Numeric Keypad see , on Installing an IR Receiver into the KeypadKeypad Location Main Keypad IR Receiver HolsterKeypad Backlighting Jumper Connecting the IR ReceiverC4630 SE Keypad Connections To the KeypadExternal Keypad Power see Figure Mounting the C4630 SE KeypadsKeypad Ribbon Cable Changing the Main Keypad Source Buttons Insert ToolInto Openings C4630 SE Out-Of-The-Box Functions Optional C4630 SE IR Remote ControlALL OFF Switch Front Panel Controls and IndicatorsInstalling the Sonance Control Manager Software Sonance Control Manager SoftwareTo transfer programming to the C4630 SE Transferring System Information to the C4630 SEUpdating the Sonance Control Manager Software and Firmware Upgrading Sonance Control Manager SoftwareUpgrading the C4630 SE Firmware Upgrade Firmware Warning ScreenDevice Screen Creating a New C4630 SE SystemRenaming C4630 SEs in a System with Multiple Units To cor rect for too low or too high a level Feedback , etc Setting Up a ZoneSetting Up Sources Rear-Panel BBE ON/OFF SwitchesBBE Sound Enhancement Programming C4630 SE Keypad Macros Device Screen FigureGeneral Macro Programming Notes Fi g u re 4 2 Z o n e 1 P ro g r a m m i n g S c re e n Building MacrosCommand From Library IR Commands Macro Command TypesAdding an IR Command to a Macro Macro Editor Screen FigureMacro Editor Screen with IR Command Library Selected Dragging Commands into the Macro WindowProgrammed IR Output Port Selector Modifying the IR Library IR Library ManagerIR Library Manager Edit Tab Editing IR Commands in the User IR LibraryReady to Align Remote and IR Learner Adding Function Names to the Function ListInternal Commands Waveform View TabHex View Tab Internal Command Window Time DelayTime Delay Macro Window Status TestRS-232 Command Outbound Serial Control RS-232 Macro Editor Window with an RS-232 command stringRS-232 Macro Window Repeat Steps Stop MacroControlling the C4630 SE via RS-232 Inbound Serial Control Drag Commands Into BracketToggle IR Code C4630 SE Inbound Serial Protocol fixedC4630 SE Inbound Serial Commands C4630 SE Status Queries Inbound Serial Control of C4630 SEs in Multi-Unit SystemsSerial Commands Simulate Button Press Commands in Multi-Unit SystemsPowering K2 Keypads Wiring K2 and K1 Keypad ConnectionsC4630 SE Extra Command Macros Expanded Control FeaturesProgramming a K2 Button to Trigger a C4630 SE Extra Command Triggering C4630 SE Extra Command Macros From the K1 and K2Generating a System Configuration Report Getting System Configuration InformationSystem Configuration Report Showing RS-232 Macro Commands Finding RS-232 Commands in MacrosAudio Performance SpecificationsProblem Solution TroubleshootingAudio Infrared Control Problem Important Freight collect shipments will be refused Technical Assistance and ServiceExclusions and Limitations Limited Warranty Coverage U.S.A. OnlySystem Notes Page 33-4119 07/07