Kenmore 790.7937, 790.7936 manual Fig2, Operating the Bridge Burner for Bridge Burner models only

Page 12

Surface Cooking

•Setting Bridge Burner Control (some models)

•Operating the Bridge Burner (some models)

Setting the Bridge Burner (for Bridge Burner models only):

The Bridge Burner should be used with rectangular shaped cookware. Cookware like the cast-iron Griddle that is supplied with your range is designed specifically for best results with the Bridge Burner.

The Bridge Burner feature may be used to combine the cooking power of 2 or if needed 3 gas surface Burners located along the left-hand side of the glass cooktop.The left rear and left center Burners are controlled by the left rear surface Control Knob. In addition the left front Burner may be added to the Bridge Burner with the left front gas Control Knob (See Fig. 1).

Operating the Bridge Burner (for Bridge Burner models only):

1.Push the left rear surface control knob in and turn counterclockwise out of the OFF position (See Fig. 1).

3.Release the knob and rotate to the LITE position (See Figs. 1 & 2). Note: All electronic surface ignitors will spark at the same time. However, only the selected surface Burner will lite.

3.Visually check that the left rear Burner has lit.

4.Contine to rotate the gas control knob clockwise past the first LO setting to the arrowmarked BRIDGE.

5.Visually check that both the left rear and left center Burners are lit.

6.When both burners are lit, continue to turn the control knob counterclockwise to adjust to the desired flame size for both burners together. Note: The markings between the 2nd HI and LO settings on the left rear control knob adjust the flame size for both burners. Use the guide marks between the 2nd HI and LO settings and adjust the flame size as needed (Refer to Fig. 3).

7.Add the left front Burner if needed. Once lit, visually adjust the flame size of the left front Burner to match the flame size of the Bridge Burner.

8.Place cooking utensil centered over the left-hand cooktop surface Burner Grate. DO NOT cook with any of the surface control knobs in the LITE position (The electronic ignitor will continue to spark if the knob is left in the LITE position).

 

 

Left Rear

 

 

Bridge

 

Left Rear

Burner

 

Bridge

Burner

 

Burner

flame

 

Burner

flame

 

LITE

adjustment

 

LITE

adjustment

 

position

area

i

position

area

 

i

i

i

i

OFF

)Hi

 

LO

Hi

LO

Fig. 3 - Left Rear Bridge Burner Surface Control Knob markings

Left

Rear

Burner

Left

Burner

Left

Burner

88

FRONT

}{EAR

BRIDGE

Fig. 1

i

__

Fig2

Note: Ifonly the left rear surface Burner is needed, follow the instructions provided below.

Operating only the Left rear Gas Surface Burner (for models equipped with Bridge Burner):

1.Place cooking utensil centered overthe left-rear surface Burner Grate.

2.Push the left rear surface control knob in and turn counterclockwise out of the OFF position (See Fig. 2).

3.Release the knob and rotate to the LITE position. Note: All electronic surface ignitors will spark at the same time. However, only the left rear Burner will ignite.

4.Visually check that the left-rear burner has lit. Adjust the flame size by turning the control knob between the first HI and LO settings (See Fig. 3). DO NOT cook with the surface control knob in the LITE position (The electronic ignitor will continue to spark if the knob is left in the LITE position).

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Estufa a gas Contents Important Safety Instructions Important Instructions for Using Important Instructions for Cleaning Your RangeImportant Safety Notice For CERAMIC-GLASS Cook TOP Models some modelsGrounding Instructions Conversion to Liquefied Petroleum Gas or L.P. GasSears Installation Service Maintenance AgreementsSears Maintenance Agreement U.S.ABefore Using Your Range 9k!iiN t ,3Range Features Your Elite Gas Range Features IncludeBefore Setting Oven Controls Oven Vent LocationRemoving & Replacing Oven Racks Types of Oven RacksBefore Setting Surface Controls Baking Layer Cakes with 1 or 2 Oven RacksAir Circulation in the Oven Control Locations of the Gas Surface BurnersSetting Proper Surface Burner Flame Size Surface CookingOperating the Gas Surface Burners Size Type of CookingFig2 Operating the Bridge Burner for Bridge Burner models onlySetting Warmer Drawer Controls Using the GriddleUsing the Warmer Drawer Care & Seasoning of the GriddleWarmer Drawer Recommended Food Settings Table Food Item To Set the Warmer Drawer & Bread Proofing ControlsWarmer Drawer Removal Preparing Bread Dough for the Warmer DrawerTo Remove and Replace Warmer Warm & Ready TM Drawer To Remove Warmer DrawerElectronic Oven Control Pad Features Control Pad SettingsMinimum & Maximum Setting Oven Controls Setting the ClockTo set the clock example below for PressdisplaySetting Continuous Bake or 12 Hour Energy Saving SettingTo set the Kitchen Timer example for 5 minutes To cancel the Kitchen Timer before the set time has run outSetting Oven Lockout Feature To activate the Oven Lockout featureSetting Temperature Display m Fahrenheit or Celsius To reactivate normal oven operationSetting Silent Control Operation Saving and Recalling Recipe SettingsFor 7seconds Setting Preheat To set the Preheat temperature for 350FSetting Bake To set the Bake Temperature to 350FInstructions Setting Timed Bake Bake finishesSetting Delay Start To program the oven for a Delay Start Delayed TimedWhen the set bake time runs out To set the oven to broil at the default setting 550F BroilingSearing Grill RecommendedSetting Food Categories Features MeatsCakes Breads @ PadsSetting Convection Bake To set the oven for Convection Bake Temperature to 350FCakes have better results when baked using the Cakes Pad Tips for Convection BakeTo set the Convection Convert feature To Set Add 1 Minute FeatureSetting the Slow Cook Feature Optional @Setting the Sabbath Day Feature Setting the Warm & Hold TM Feature To set Warm & HoldPRESS,,2 To set Warm & Hold to turn on automaticallySelf-Cleaning Self-Cleaning OvenAdhere to the following cleaning precautions Clean will flash, 300 hours Press 200 to 400 using Number padsWhen the Self-Clean cycle is done Stopping or Interrupting a Self-Cleaning cycleAdjusting Oven Temperature To adjust the oven temperature higherTo adjust the oven temperature lower Press DisplayGeneral Care & Cleaning How to CleanSurfaces Glass control panelCare & Cleaning of Stainless Steel some models Removing & Replacing the Lift-Off Oven DoorDoor Care Instructions Cleaning the Cooktop, Burner Heads, Caps & Grates Cleaning Recommendations for the Ceramic Glass Cooktop Plastic or foods with a high sugar contentFor models with a Ceramic Glass Cooktop only For light to moderate soilChanging Oven Lights To replace the oven light bulbsBefore You Call Possible CAUSE/SOLUTION Self-Cleaning sectionOccurrence ScratchesorabrasionsoncooktopsurfaceRecipes for Slow Cook Slow Cook Turkey BreastMY-HOME Our HomeCanada Call anytime, day or night U.S.A. and Canada
Top Page Image Contents