Makita EM2650UH/Em2650LH manual Replacing the nylon cord, 100 mm

Page 18

Replacing the nylon cord

WARNING: Make sure that the cover of the nylon cutting head is secured to the housing properly as described below. Failure to properly secure the cover may cause the nylon cutting head to fly apart resulting in serious personal injury.

Press inward on the housing latches and lift upward to remove the cover. Discard any of the remaining nylon cord.

Hook the middle of the new nylon cord to the notch located at the center of the spool between the 2 channels provided for the nylon cord. One side of the cord should be about 80 mm longer than the other side.

Wind both ends firmly around the spool in the direction marked on the head for left hand direction indicated by LH.

Wind all but about 100 mm of the cords, leaving the ends temporarily hooked through a notch on the side of the spool.

Cover

Latches

Press Press

80 mm

For left hand

Spool

rotation

 

100 mm

Notches

Mount the spool in the housing so that the grooves and protrusions on the spool match up with those in the housing. Keep the side with letters on the spool visible on the top. Now, unhook the ends of the cord from their temporary position and feed the cords through the eyelets to come out of the housing.

Align the protrusion on the underside of the cover with the slots of the eyelets. Then push cover firmly onto the housing to secure it. Make sure the latches fully spread in the cover.

Eyelets

Cover

Protrusion (Not shown)

Slot of eyelet

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents EM2650UH EM2650LH ImportanteSymbols Table of ContentsIntended use of the machine Safety InstructionsGeneral Instructions Personal protective equipmentResting Transport Refueling Maintenance Tool replacement RefuelingCutting Tools Maintenance instructionsMethod of operation KickbackWhen asking for help, please give the following information Never straighten or weld damaged cutting toolsFirst Aid Technical Data EM2650UH, EM2650LH Model EM2650UH EM2650LHDesignation of Parts EM2650UH EM2650LHMounting of Handle For machines with bike handle modelsFor machines with loop handle Use of metal blade EM2650UH, optional accessory for EM2650LH Use of nylon cutting head EM2650UH, EM2650LHMounting of Protector For EM2650UHFor EM2650LH Mounting of Cutter Blade or Nylon Cutting Head Mounting of cutterblade with the hex wrench still in placeMounting of nylon cutting head Before Start of Operation Point 1 in Replacement of oil Oil capOil volume Inspection and refill of engine oilStorage period of fuel RefuelingHandling of fuel FuelPoints in Operation and HOW to Stop Correct Handling of MachineStarting Startup after warm-up operation Stopping Adjustment of LOW-SPEED Rotation IdlingResharpening the Cutting Tool Checkup of LOW-SPEED RotationReplacing the nylon cord 100 mmDaily checkup and maintenance Replacement of Engine OILServicing Instructions Cleaning of AIR Cleaner Points in Handling Air Cleaner ElementPoints on OIL Cleaning of Parts Cleaning of Fuel FilterReplacement of Fuel Pipe Replacement of Gaskets and PackingsFault location Fault System Observation CauseStorage Operation Operating time BeforeDaily 30h 50h 200h 10h RestStarts. Once engine starts, cutter blade TroubleshootingState of abnormality Probable cause malfunction Remedy BladeEmission Compliance Period MANUFACTURER’S Warranty Coverage Procedure Interval Emission Component Defect Warranty Period Parts CoveredObtaining Warranty Service What is not CoveredOWNER’S Warranty Responsibilities HOW to Make a Claim Pictogrammes Table des matièresUtilisation normale de la machine Consignes DE SécuritéConsignes générales Équipement de protection personnelPause Transport Remplissage Entretien Remplacement d’outil RemplissageMouvement de recul Mode de fonctionnementOutils de coupe Prévention des mouvements de reculPremiers soins Données Techniques EM2650UH, EM2650LH Modèle EM2650UH EM2650LHDésignation DES Pièces Désignation DES PiècesMontage DE LA Poignée Pour les machines avec guidonPour les machines avec poignée arceau Utilisation d’une tête à fils nylon EM2650UH, EM2650LH Poignée SangleMontage DU Protecteur Pour le EM2650UHPour le EM2650LH Montage DE LA Lame DE Coupe OU DE LA Tête À Fils Nylon MakitaMontage de la tête à fils nylon Avant Utilisation Inspection et remplissage de l’huile moteurQuantité d’huile Environ 0,08 l Entreposage de l’essence RemplissageManipulation de l’essence CarburantDétachement Manipulation Correcte DE LA MachineFixation de la sangle d’épaule DémarrageDémarrage après le réchauffage RemarqueRéglage DE LA Rotation À Faible Vitesse Ralenti Réaffûtage DE L’OUTIL DE CoupeArrêt Vérification DE LA Rotation À Faible VitesseRemplacement du fil nylon Instructions D’ENTRETIEN Remplacement DE L’HUILE MoteurHuile recommandée Vérification et entretien quotidiensRemarques Concernant L’HUILE Nettoyage DU Filtre À AIRVérification DE LA Bougie D’ALLUMAGE Remplacement DU Tuyau D’ALIMENTATION EN EssenceRemplacement DES Joints ET Garnitures Lubrification DU Carter D’ENGRENAGEEmplacement des défaillances EntreposageDéfaillance Système Observation Cause 30 h 50 h 200 h Quotidien FonctionnementArrêt PauseFois le moteur démarré, la rotation de la Anomalie Cause probable dysfonctionnement SolutionDépannage Lame de coupe commence. Faites trèsSímbolos ÍndicePáginaUso intencionado de la herramienta Instrucciones DE SeguridadInstrucciones generales Equipo protector personalResuministro de combustible Retrocesos bruscos Método de operaciónPiezas cortadoras Prevención de retrocesos bruscosPrimeros auxilios Especificaciones Técnicas EM2650UH, EM2650LH Modelo EM2650UH EM2650LHIdentificación DE LAS Piezas Identificación DE LAS PiezasColocación DEL Mango Para modelos equipados con mango tipo bicicletaPara modelos equipados con mango tipo redondo Uso de la cabeza cortadora de nailon EM2650UH, EM2650LH Colocación DEL Protector Para EM2650UHPara EM2650LH Colocación DEL Disco Cortador O Cabeza Cortadora DE Nailon Colocación de la cabeza cortadora de nailonInspeccione y resuministre el aceite del motor Volumen de aceite Aprox ,08LAntes DE Iniciar LA Operación Punto 1 en el reemplazo del aceite Tapa del aceitePeriodo de almacenamiento del combustible Reabastecimiento DE CombustibleManejo del combustible CombustibleManejo Correcto DEL Equipo Puntos EN LA Operación Y Cómo Detener LA OperaciónArranque DEL Motor Arranque tras la operación de calentamiento NotaAjuste DE LA Rotación DE Baja Velocidad Estado Pasivo Reafilado DE LA Pieza CortadoraParo DE LA Operación Revisión DE LA Rotación DE Baja VelocidadReemplazo del cordón de nailon Instrucciones DE Servicio Revisión y mantenimiento diariosReemplazo DEL Aceite DEL Motor Puntos Sobre EL Aceite Limpieza DEL Filtro DE AirePuntos en el manejo del elemento del filtro de aire Inspección DE PERNOS, Tuercas Y Tornillos Engrasado DE LA Caja DE CambiosRevisión DE LA Bujía DE Encendido Limpieza DE LAS PiezasAtención tras el almacenamiento de largo plazo AlmacenamientoAtención Determinación de fallasOperación Antes Tras la DiarioAcción 30h 50h 200hResolución DE Problemas Estado de anomalía Causa probable falla SoluciónCortador Periodo DE Conformidad Sobre Emisiones Cobertura DE LA Garantía DEL Fabricante Procedimiento IntervaloPeriodo DE Garantía POR Defectos DE Componentes DE Emisiones Piezas CubiertasObtención DE Servicio DE Garantía LO QUE no Está CubiertoResponsabilidades DEL Propietario Para LA Garantía Cómo Preparar UNA Reclamación Page Advertencia

EM2650UH/Em2650LH specifications

The Makita EM2650UH and EM2650LH are advanced brushcutters designed for professional landscapers and gardening enthusiasts who require powerful and reliable tools. These models are part of Makita's renowned outdoor power equipment range, offering exceptional performance and cutting efficiency.

One of the standout features of both the EM2650UH and EM2650LH is their powerful 25.7 cc two-stroke engine. This engine provides ample power for various cutting applications, ranging from light grass trimming to tougher brush clearing tasks. The engines are designed for efficient fuel consumption, enabling longer operational time with fewer refueling stops.

These brushcutters are equipped with a U-shaped handle design that allows for a comfortable grip and improved control during operation. This ergonomic feature reduces fatigue, enabling users to work for extended periods without discomfort. Additionally, the EM2650UH model features a unique telescopic shaft that allows for adjustments, accommodating users of varying heights and ensuring optimal control.

Another innovative technology incorporated into these models is the "Easy Start" system. This feature significantly reduces the effort required to start the engine, enhancing user experience, especially in challenging conditions. Additionally, both models include a heavy-duty nylon cutting head designed for speed and efficiency, allowing for quick line changes and minimal downtime.

The EM2650UH and EM2650LH also feature Makita's anti-vibration technology, which minimizes user fatigue during prolonged use by absorbing vibrations generated during operation. This ensures smoother operation and improved precision in cutting tasks.

Durability is another key characteristic of these brushcutters. Constructed with high-quality materials, they can withstand the rigors of professional use in various environments, ensuring reliability and longevity. With an impressive cutting width, these models can tackle larger areas efficiently, making them ideal for landscaping businesses and lawn care professionals.

In summary, the Makita EM2650UH and EM2650LH brushcutters combine power, comfort, and efficiency, making them top choices for anyone serious about outdoor maintenance. With their ergonomic design, advanced starting technology, and robust performance features, they offer the ideal balance for tackling any grass or brush cutting job effectively and comfortably.
Top Page Image Contents