Makita EM2650UH/Em2650LH Resharpening the Cutting Tool, Stopping, Checkup of LOW-SPEED Rotation

Page 17

STOPPING

1)Release the throttle lever (2) fully, and when the engine rpm has lowered, set the I-O switch to STOP the engine will now stop.

2)Be aware that the cutting head may not stop immediately and allow it to slow down fully.

 

STOP

(1)

 

 

STOP

(2)

 

 

 

(2)

 

 

(1)

 

 

EM2650LH

 

EM2650UH

ADJUSTMENT OF LOW-SPEED ROTATION (IDLING)

When it is necessary to adjust the low-speed rotation (idling), perform it by the carburetor adjusting screw.

CHECKUP OF LOW-SPEED ROTATION

––Set the low-speed rotation to 3,000 min-1.

If it is necessary to change the low speed rotation (idle) speed, use a phillips head screw driver on the screw illustrated on the right.

––Turn the adjusting screw to the right, and the engine rotation will increase. Turn the adjusting screw to the left, and the engine rotation will drop.

––The carburetor is generally adjusted before shipment. After several tanks of gasoline the idle rpm may need to be readjusted.

Carburetor

Adjusting

screw

RESHARPENING THE CUTTING TOOL

CAUTION: The cutting tools shown in the illustration are not to be sharpened. Manual resharpening will result in imbalances of the cutting tool causing vibrations and damage to the equipment.

NOTE: To increase the service life of the cutter blade it may be turned over once, until both cutting edges have become blunt.

NYLON CUTTING HEAD

The grass trimmer cutting head is a dual line trimmer head that has bump & feed mechanism.

The nylon cutting head will feed out the proper length of nylon line after tapping the trimmer head on the ground by changes in centrifugal force caused by increasing or decreasing rpms.

Operation

––Increase the nylon cutting head speed to approx. 6,000 min-1. Bump the trimmer head lightly on the ground.

––The most effective cutting area is shown by the shaded area.

––If the nylon cord does not feed out, rewind/replace the nylon cord by following the procedures described under “Replacing the nylon cord.”

Most effective cutting area

17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Importante EM2650UH EM2650LHTable of Contents SymbolsGeneral Instructions Safety InstructionsIntended use of the machine Personal protective equipmentRefueling Resting Transport Refueling Maintenance Tool replacementMethod of operation Maintenance instructionsCutting Tools KickbackFirst Aid When asking for help, please give the following informationNever straighten or weld damaged cutting tools Model EM2650UH EM2650LH Technical Data EM2650UH, EM2650LHEM2650UH EM2650LH Designation of PartsFor machines with loop handle Mounting of HandleFor machines with bike handle models Use of nylon cutting head EM2650UH, EM2650LH Use of metal blade EM2650UH, optional accessory for EM2650LHFor EM2650LH Mounting of ProtectorFor EM2650UH Mounting of nylon cutting head Mounting of Cutter Blade or Nylon Cutting HeadMounting of cutterblade with the hex wrench still in place Oil volume Point 1 in Replacement of oil Oil capBefore Start of Operation Inspection and refill of engine oilHandling of fuel RefuelingStorage period of fuel FuelStarting Points in Operation and HOW to StopCorrect Handling of Machine Startup after warm-up operation Resharpening the Cutting Tool Adjustment of LOW-SPEED Rotation IdlingStopping Checkup of LOW-SPEED Rotation100 mm Replacing the nylon cordServicing Instructions Daily checkup and maintenanceReplacement of Engine OIL Points on OIL Cleaning of AIR CleanerPoints in Handling Air Cleaner Element Replacement of Fuel Pipe Cleaning of Fuel FilterCleaning of Parts Replacement of Gaskets and PackingsStorage Fault locationFault System Observation Cause Daily 30h 50h 200h Operating time BeforeOperation 10h RestState of abnormality Probable cause malfunction Remedy TroubleshootingStarts. Once engine starts, cutter blade BladeEmission Compliance Period MANUFACTURER’S Warranty Coverage Procedure Interval Parts Covered Emission Component Defect Warranty PeriodOWNER’S Warranty Responsibilities Obtaining Warranty ServiceWhat is not Covered HOW to Make a Claim Table des matières PictogrammesConsignes générales Consignes DE SécuritéUtilisation normale de la machine Équipement de protection personnelRemplissage Pause Transport Remplissage Entretien Remplacement d’outilOutils de coupe Mode de fonctionnementMouvement de recul Prévention des mouvements de reculPremiers soins Modèle EM2650UH EM2650LH Données Techniques EM2650UH, EM2650LHDésignation DES Pièces Désignation DES PiècesPour les machines avec poignée arceau Montage DE LA PoignéePour les machines avec guidon Poignée Sangle Utilisation d’une tête à fils nylon EM2650UH, EM2650LHPour le EM2650LH Montage DU ProtecteurPour le EM2650UH Montage de la tête à fils nylon Montage DE LA Lame DE Coupe OU DE LA Tête À Fils NylonMakita Quantité d’huile Environ 0,08 l Avant UtilisationInspection et remplissage de l’huile moteur Manipulation de l’essence RemplissageEntreposage de l’essence CarburantFixation de la sangle d’épaule Manipulation Correcte DE LA MachineDétachement DémarrageRemarque Démarrage après le réchauffageArrêt Réaffûtage DE L’OUTIL DE CoupeRéglage DE LA Rotation À Faible Vitesse Ralenti Vérification DE LA Rotation À Faible VitesseRemplacement du fil nylon Huile recommandée Remplacement DE L’HUILE MoteurInstructions D’ENTRETIEN Vérification et entretien quotidiensNettoyage DU Filtre À AIR Remarques Concernant L’HUILERemplacement DES Joints ET Garnitures Remplacement DU Tuyau D’ALIMENTATION EN EssenceVérification DE LA Bougie D’ALLUMAGE Lubrification DU Carter D’ENGRENAGEDéfaillance Système Observation Cause Emplacement des défaillancesEntreposage Arrêt Quotidien Fonctionnement30 h 50 h 200 h PauseDépannage Anomalie Cause probable dysfonctionnement SolutionFois le moteur démarré, la rotation de la Lame de coupe commence. Faites trèsÍndicePágina SímbolosInstrucciones generales Instrucciones DE SeguridadUso intencionado de la herramienta Equipo protector personalResuministro de combustible Piezas cortadoras Método de operaciónRetrocesos bruscos Prevención de retrocesos bruscosPrimeros auxilios Modelo EM2650UH EM2650LH Especificaciones Técnicas EM2650UH, EM2650LHIdentificación DE LAS Piezas Identificación DE LAS PiezasPara modelos equipados con mango tipo redondo Colocación DEL MangoPara modelos equipados con mango tipo bicicleta Uso de la cabeza cortadora de nailon EM2650UH, EM2650LH Para EM2650LH Colocación DEL ProtectorPara EM2650UH Colocación de la cabeza cortadora de nailon Colocación DEL Disco Cortador O Cabeza Cortadora DE NailonAntes DE Iniciar LA Operación Volumen de aceite Aprox ,08LInspeccione y resuministre el aceite del motor Punto 1 en el reemplazo del aceite Tapa del aceiteManejo del combustible Reabastecimiento DE CombustiblePeriodo de almacenamiento del combustible CombustibleArranque DEL Motor Manejo Correcto DEL EquipoPuntos EN LA Operación Y Cómo Detener LA Operación Nota Arranque tras la operación de calentamientoParo DE LA Operación Reafilado DE LA Pieza CortadoraAjuste DE LA Rotación DE Baja Velocidad Estado Pasivo Revisión DE LA Rotación DE Baja VelocidadReemplazo del cordón de nailon Reemplazo DEL Aceite DEL Motor Instrucciones DE ServicioRevisión y mantenimiento diarios Puntos en el manejo del elemento del filtro de aire Puntos Sobre EL AceiteLimpieza DEL Filtro DE Aire Revisión DE LA Bujía DE Encendido Engrasado DE LA Caja DE CambiosInspección DE PERNOS, Tuercas Y Tornillos Limpieza DE LAS PiezasAtención AlmacenamientoAtención tras el almacenamiento de largo plazo Determinación de fallasAcción Antes Tras la DiarioOperación 30h 50h 200hCortador Resolución DE ProblemasEstado de anomalía Causa probable falla Solución Periodo DE Conformidad Sobre Emisiones Cobertura DE LA Garantía DEL Fabricante Intervalo ProcedimientoPiezas Cubiertas Periodo DE Garantía POR Defectos DE Componentes DE EmisionesResponsabilidades DEL Propietario Para LA Garantía Obtención DE Servicio DE GarantíaLO QUE no Está Cubierto Cómo Preparar UNA Reclamación Page Advertencia

EM2650UH/Em2650LH specifications

The Makita EM2650UH and EM2650LH are advanced brushcutters designed for professional landscapers and gardening enthusiasts who require powerful and reliable tools. These models are part of Makita's renowned outdoor power equipment range, offering exceptional performance and cutting efficiency.

One of the standout features of both the EM2650UH and EM2650LH is their powerful 25.7 cc two-stroke engine. This engine provides ample power for various cutting applications, ranging from light grass trimming to tougher brush clearing tasks. The engines are designed for efficient fuel consumption, enabling longer operational time with fewer refueling stops.

These brushcutters are equipped with a U-shaped handle design that allows for a comfortable grip and improved control during operation. This ergonomic feature reduces fatigue, enabling users to work for extended periods without discomfort. Additionally, the EM2650UH model features a unique telescopic shaft that allows for adjustments, accommodating users of varying heights and ensuring optimal control.

Another innovative technology incorporated into these models is the "Easy Start" system. This feature significantly reduces the effort required to start the engine, enhancing user experience, especially in challenging conditions. Additionally, both models include a heavy-duty nylon cutting head designed for speed and efficiency, allowing for quick line changes and minimal downtime.

The EM2650UH and EM2650LH also feature Makita's anti-vibration technology, which minimizes user fatigue during prolonged use by absorbing vibrations generated during operation. This ensures smoother operation and improved precision in cutting tasks.

Durability is another key characteristic of these brushcutters. Constructed with high-quality materials, they can withstand the rigors of professional use in various environments, ensuring reliability and longevity. With an impressive cutting width, these models can tackle larger areas efficiently, making them ideal for landscaping businesses and lawn care professionals.

In summary, the Makita EM2650UH and EM2650LH brushcutters combine power, comfort, and efficiency, making them top choices for anyone serious about outdoor maintenance. With their ergonomic design, advanced starting technology, and robust performance features, they offer the ideal balance for tackling any grass or brush cutting job effectively and comfortably.
Top Page Image Contents