Craftsman 900.74547, C935.51850 manual Spool of AFS Cutting Line

Page 8

advanced automatic line feeding mechanism senses when more cutting line is needed and feeds and trims the correct length of line whenever it’s required. DO NOT BUMP unit on ground in attempt to feed line or for any other purposes.

FITTING A NEW SPOOL OF AFS CUTTING LINE (FIGURES 11 & 12)

•Unplug the tool.

•Depress the tabs (a) and remove the cassette (b) from the cassette housing

(c)in the trimmer head (figure 11).

11

d

b

b

a

trimming blade (i), cut them off so that they just reach the blade (figure 11).

12

d

ga

f

e

 

 

b

WINDING NEW LINE ONTO AN EMPTY SPOOL (FIGURES 13 &14)

You may wind new cutting line onto an empty spool. Replacement packs of .065 inch (1.65 mm) cutting line are available from your Sears store.

h

c

•

Remove the empty spool from the tool

 

as described in “FITTING A NEW

 

SPOOL OF AFS CUTTING LINE”.

•

Remove any remaining cutting line

i

•Grasp empty spool (d) with one hand and cassette with other hand and pull spool out from cassette. If lever (e) in base of cassette becomes dislodged, replace in correct position before inserting new spool into cassette.

•Remove any dirt and grass from the cassette and housing.

•Take the new spool and push it onto the boss (f) (figure 12) in the cassette. Rotate the spool slightly until it is seated.

•Unfasten the end of one of the cutting lines and guide the line into one of the eyelets (g) (figure 12). The line should protrude approximately 4-3/8 inches (111mm) from the cassette.

•Unfasten the end of the other cutting line and guide the line into the other eyelet. The line should protrude approximately 4-3/8 inches (111mm) from the cassette.

•Align the cassette tabs (a) with the slots

(h) in the housing (figure 11).

•Push the cassette onto the housing until it snaps securely into place.

CAUTION: To avoid tool damage, If the cutting lines protrude beyond the

from the spool.

• First wind new line onto the uppermost

part of the spool.

- Feed 3/4 inch (19mm) of cutting line

into one of the line anchoring slots.

- Wind the cutting line onto the spool in

the direction of the arrow on the spool.

Make sure to wind the line neatly and in

layers. Do not crisscross (figure 13).

13

-When the wound cutting line reaches the recesses (j), cut the line. (figure 14).

-Temporarily park the line in the holding slots (k) on one side of the spool as shown in the inset in figure 14.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Operator’s Manual Form No APR. ‘08Trimmer Diagram Sears WarrantySpecific Safety Warning InstructionsGeneral Safety Warnings and Instructions for ALL Tools Always Wear EYE ProtectionAvoid Accidentally Starting Store Idle Tools IndoorsAdditional Warnings for String Trimmers Safety Warnings Double InsulationSafety Warnings and Instructions Polarized Plugs Assembly Instructions Attaching the TWO Piece GuardAttaching the Auxiliary Handle Phillips ScrewdriverHeight Adjustment Attaching Extension CordSwitching on and OFF Operating InstructionsBlower Function Figure Cutting Line / Line FeedingSpool of AFS Cutting Line Keep the air intake slots clean to avoid overheating AccessoriesMaintenancetroubleshooting Need More HELP? Parts Diagrama DEL Cortacerco Garantia SearsAdvertencia DE Seguridad Especifica LEA Todas LAS InstruccionesLa protección del Interruptor DE Protector nunca utilice esta herramienta sin el protectorCarrete están dañados Advertencia Adicionales Para Podadores DE Cadena Cordones DE ExtensionAsegúrese que su extensión esté en Instrucciones Para EL Ensamblaje Colocación DEL Protector DE DOS PiezasDestornillador Phillips CanalRanura Colocación DEL Mango AuxiliarAjuste DE Altura Instrucciones DE Operación Colocación DEL Cable ProlongadorCon la unidad encendida, gire Lado a lado, como se muestra en laFunción DE Sopladora Figura Mantenimiento ¿NECESITA MÁS AYUDA? LE Manuel DE Lopérateur Garantie Sears Lire Toutes LES DirectivesGarantie Craftsman Complète DE Deux ANS Réduction DES Risques DE BlessuresPage Mesures de sécurité normales lors de Ou une double épaisseur d’isolant quiProtègent l’utilisateur contre les risques Réparer ou remplacer les cordonsLanguette Mesures DE Sécurité Fiche PolariséeDirectives DE Montage Encoche Fixation DE LA Poignée AuxiliaireRéglable DE LA Hauteur Directives D’UTILISATION Fixation DE LA RallongeMise EN Marche ET Arrêt Pour éteindre l’outil, relâcher le levier de déclenchementFonction DE Souffleur Figure FIL Tranchant / Avance DU FILMaintenance Rembobinage DE FIL Neuf SUR UNE Bobine Vide Figures 13 ET’assurer que le fil sort d’au plus DépannageUtiliser la bobine de rechange Craftsman de modèle n Parts

C935.51850, 900.74547 specifications

The Craftsman 900.74547 and C935.51850 are two versatile tools that combine efficiency and innovation, perfect for DIY enthusiasts and professional craftsmen alike. These models exemplify the Craftsman commitment to quality, offering a blend of power, durability, and user-friendly features.

The Craftsman 900.74547 is a high-performance tool with a robust design, featuring a powerful motor that ensures consistent performance across various applications. One of its standout characteristics is the variable speed control, allowing users to adjust the speed according to the task at hand, whether it's cutting, sanding, or drilling. This flexibility makes it suitable for a wide range of projects, from intricate woodworking to heavy-duty construction tasks.

On the other hand, the C935.51850 is designed with advanced technology that enhances precision and ease of use. This model comes equipped with an ergonomic grip, ensuring comfort during extended use. It also features a built-in LED light that illuminates the work area, making it ideal for low-light conditions. The tool's construction is sturdy, designed to withstand the rigors of professional use while remaining lightweight enough for easy handling.

Both models boast a quick-release chuck system, enabling users to change bits swiftly without the need for additional tools. This feature significantly reduces downtime during tasks, allowing for seamless transitions between different applications. Furthermore, they are compatible with a wide range of accessories, providing added versatility for various jobs.

In terms of safety, the Craftsman 900.74547 and C935.51850 come with integrated safety features, including a lock-off switch that prevents accidental starts. This attention to safety is crucial for ensuring user confidence, especially in high-pressure environments.

In conclusion, both the Craftsman 900.74547 and C935.51850 are exemplary tools that showcase innovation and practicality. With their powerful motors, variable speed controls, ergonomic designs, and safety features, they represent a reliable choice for anyone looking to tackle a variety of projects, whether at home or in a professional setting. Selecting either of these models ensures that users have a dependable ally at their side, ready to deliver exceptional results every time.
Top Page Image Contents