Craftsman C935.51850, 900.74547 manual Accessories, Maintenancetroubleshooting

Page 9

14

 

j

k

k

•Repeat the above procedure for the second cutting line on the lower section of the spool.

•Fit the spool onto the tool as described in “FITTING A NEW SPOOL OF CUTTING LINE”.

CAUTION: Before you begin trimming, only use the appropriate type of cutting line. Ensure that cutting line is present in both sections of the spool (figure 12).

2.Your trimmer line can dry out over time. To keep your line in top condition, store spare pre-wound spools or bulk line in a plastic, sealable bag with a tablespoon of water.

3.Plastic parts may be cleaned by using a mild soap and a damp rag.

4.The line cutter on the edge of the guard can dull over time. It is recommended you periodically touch-up the sharpness of the blade with a file.

ACCESSORIES

Use Craftsman replacement spool Model No. 85942.

Reload nylon line (either bulk or prewound replacement spool) as described in this manual.

•USE ONLY .065 inch (1.65 mm)

DIAMETER NYLON MONOFILAMENT LINE. Do not use serrated or heavier gauge line, as they will overload the motor and cause overheating. The unit only functions properly with .065 inch (1.65 mm) diameter nylon monofilament line. This line is available at your local Sears store or other Craftsman outlet.

WARNING: The use of any accessory not recommended by Sears for use with this tool could be hazardous.

MAINTENANCETROUBLESHOOTING

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment should be performed by a Sears or other qualified service dealer, always using identical replacement parts.

WARNING: To avoid serious injury, switch off and unplug the tool before performing any maintenance.

1.Keep the air intake slots (figure 15) clean to avoid overheating.

15

9

WARNING: To avoid serious injury, switch off and unplug the tool before performing any maintenance.

Tool runs slowly

•Check that the cassette housing can rotate freely. Carefully clean it if necessary.

•Check that the cutting line does not protrude more than approximately 4-3/8 inches (111mm) from the cassette. If it does, cut it off so that it just reaches the line trimming blade.

Automatic line feed does not work

•Keep the tabs depressed and remove the cassette from the cassette housing in the trimmer head.

•Pull the cutting line until it protrudes approximately 4-3/8 inches (111mm) from the cassette. If insufficient cutting line is left on the spool, install a new spool of cutting line.

•Align the tabs on the cassette with the cut outs in the housing.

•Push the cassette onto the housing until it snaps securely into place.

•If the cutting line protrudes beyond the trimming blade, cut it off so that it just reaches the blade.

Page 8 Page 10
Image 9
Page 8 Page 10
Contents Form No APR. ‘08 Operator’s ManualSears Warranty Trimmer DiagramSpecific Safety Warning InstructionsAlways Wear EYE Protection General Safety Warnings and Instructions for ALL ToolsAvoid Accidentally Starting Store Idle Tools IndoorsSafety Warnings Double Insulation Safety Warnings and Instructions Polarized PlugsAdditional Warnings for String Trimmers Attaching the TWO Piece Guard Assembly InstructionsAttaching the Auxiliary Handle Phillips ScrewdriverAttaching Extension Cord Height AdjustmentOperating Instructions Switching on and OFFBlower Function Figure Cutting Line / Line FeedingSpool of AFS Cutting Line Accessories MaintenancetroubleshootingKeep the air intake slots clean to avoid overheating Need More HELP? Parts Garantia Sears Diagrama DEL CortacercoAdvertencia DE Seguridad Especifica LEA Todas LAS InstruccionesProtector nunca utilice esta herramienta sin el protector Carrete están dañadosLa protección del Interruptor DE Cordones DE Extension Asegúrese que su extensión esté enAdvertencia Adicionales Para Podadores DE Cadena Colocación DEL Protector DE DOS Piezas Instrucciones Para EL EnsamblajeDestornillador Phillips CanalColocación DEL Mango Auxiliar Ajuste DE AlturaRanura Colocación DEL Cable Prolongador Instrucciones DE OperaciónCon la unidad encendida, gire Lado a lado, como se muestra en laFunción DE Sopladora Figura Mantenimiento ¿NECESITA MÁS AYUDA? LE Manuel DE Lopérateur Lire Toutes LES Directives Garantie SearsGarantie Craftsman Complète DE Deux ANS Réduction DES Risques DE BlessuresPage Ou une double épaisseur d’isolant qui Mesures de sécurité normales lors deProtègent l’utilisateur contre les risques Réparer ou remplacer les cordonsMesures DE Sécurité Fiche Polarisée Directives DE MontageLanguette Fixation DE LA Poignée Auxiliaire Réglable DE LA HauteurEncoche Fixation DE LA Rallonge Directives D’UTILISATIONMise EN Marche ET Arrêt Pour éteindre l’outil, relâcher le levier de déclenchementFIL Tranchant / Avance DU FIL Fonction DE Souffleur FigureRembobinage DE FIL Neuf SUR UNE Bobine Vide Figures 13 ET MaintenanceDépannage Utiliser la bobine de rechange Craftsman de modèle n’assurer que le fil sort d’au plus Parts

C935.51850, 900.74547 specifications

The Craftsman 900.74547 and C935.51850 are two versatile tools that combine efficiency and innovation, perfect for DIY enthusiasts and professional craftsmen alike. These models exemplify the Craftsman commitment to quality, offering a blend of power, durability, and user-friendly features.

The Craftsman 900.74547 is a high-performance tool with a robust design, featuring a powerful motor that ensures consistent performance across various applications. One of its standout characteristics is the variable speed control, allowing users to adjust the speed according to the task at hand, whether it's cutting, sanding, or drilling. This flexibility makes it suitable for a wide range of projects, from intricate woodworking to heavy-duty construction tasks.

On the other hand, the C935.51850 is designed with advanced technology that enhances precision and ease of use. This model comes equipped with an ergonomic grip, ensuring comfort during extended use. It also features a built-in LED light that illuminates the work area, making it ideal for low-light conditions. The tool's construction is sturdy, designed to withstand the rigors of professional use while remaining lightweight enough for easy handling.

Both models boast a quick-release chuck system, enabling users to change bits swiftly without the need for additional tools. This feature significantly reduces downtime during tasks, allowing for seamless transitions between different applications. Furthermore, they are compatible with a wide range of accessories, providing added versatility for various jobs.

In terms of safety, the Craftsman 900.74547 and C935.51850 come with integrated safety features, including a lock-off switch that prevents accidental starts. This attention to safety is crucial for ensuring user confidence, especially in high-pressure environments.

In conclusion, both the Craftsman 900.74547 and C935.51850 are exemplary tools that showcase innovation and practicality. With their powerful motors, variable speed controls, ergonomic designs, and safety features, they represent a reliable choice for anyone looking to tackle a variety of projects, whether at home or in a professional setting. Selecting either of these models ensures that users have a dependable ally at their side, ready to deliver exceptional results every time.
Top Page Image Contents