Assembly & Set-Up, Contents of Crate

Assembly & Set-Up

Contents of Crate

•	One Lawn Tractor	•	One Oil Drain Tube	•	One Deck Wash Hose Coupler
•	One RZT Tractor Operator’s	•	One Kohler Engine Operator’s	•	One Product Registration Card
	Manual		Manual

tractor preparation

Remove the upper crating material from the shipping pallet, and cut any bands or tie straps securing the tractor to the pallet.

Use the lift handle to raise the deck to its highest position. Engage the transmission bypass rods on each side of the tractor; then carefully roll the tractor off the shipping pallet. Disengage the bypass rods. See Figure 3-1.

4.Align the grooves in the seat adjust spacers with the sides of the adjustment slots in the pivot bracket.

5.Slide the seat adjust spacers into the slots of the pivot bracket.

6.Continue to push the seat forward in the pivot bracket until the front/left shoulder bolt of the seat assembly passes forward of the stop bracket on the seat pivot bracket. See Figure 3-2.

RH Transmission		Pull Out
RH Transmission		Pull Out
Bypass Rod		Bypass Rod

Then Lower

In Slot

Keyhole

Slot

Figure 3-1

Remove the deck wash system nozzle adapter from the manual bag and store for future use.

Install operator’s seat

The operator’s seat was partially inserted into the seat pivot bracket for shipping purposes. To install the seat proceed as follows:

1.Cut any straps securing the seat assembly and the drive control levers to the tractor. Remove any packing material.

NOTE: The seat is partially inserted into the slots of the seat pivot bracket. If the seat does not become disengaged from the pivot bracket when removing the packaging material, the pivot bracket may be pivoted upward and the seat pushed into place as described in step 6. If the seat does disengage the pivot bracket, install the seat as instructed in steps 2 thru 6.

2.Pivot the seat pivot bracket partially upward. Refer to Figure 3-2.

3.Note the grooves in the seat adjust spacers attached to the bottom of the seat, then lift the seat and position above and to the rear of the pivot bracket.

Seat	Adjustment
Seat	Slots	Seat
		Pivot
		Bracket
Seat
Adjust
Spacer

Front/Left		Seat Adjust
Front/Left	Stop Bracket	Seat Adjust
Shoulder Bolt	Stop Bracket	Lever

Figure 3-2

Refer to “Adjusting Operator’s Seat” in Maintenance & Adjustments for seat adjustment instructions.

Position Drive Control levers

The drive control levers of the tractor are lowered for shipping purposes. The flange lock nuts, hex screws, and flat washers that normally secure the control levers in their operating position are unfastened and installed in the slotted holes of the control levers for shipment. The control levers must be repositioned to operate the tractor. To reposition the control levers for operation, proceed as follows:

1.Remove the hex screw, flat washer, and flange lock nut from the slot of one of the drive control levers.

2.Lift and swing that control lever upward until the slotted hole in the lever bracket aligns with one of the holes in the pivot bracket. Refer to Figure 3-3.

RZT specifications

The Troy-Bilt RZT is a formidable lawn mower that brings a blend of efficiency, performance, and user-friendly features to the forefront of lawn care. Designed for homeowners who demand both power and precision, the RZT series offers a riding mower experience unlike any other.

One of the standout features of the Troy-Bilt RZT is its innovative Zero Turn Technology, which enables exceptional maneuverability. This technology allows users to make sharp turns and navigate around obstacles with ease, ensuring precise mowing in tight spaces. The dual lever steering system enhances control, allowing for quick direction changes and saving time on larger properties.

The engine options available with the RZT series range from powerful V-twin engines to reliable OHV engines, providing homeowners with choices that cater to their specific mowing requirements. These engines ensure robust performance, delivering the horsepower needed to tackle even the toughest grass and terrain.

The RZT models come equipped with reinforced deck materials that result in superior durability. The cutting deck typically ranges from 42 to 54 inches, allowing users to cover more ground in less time while achieving a clean, professional cut. Additionally, the adjustable cutting height feature provides versatility, enabling users to customize their mowing height based on grass type and conditions.

Troy-Bilt enhances user convenience with features such as an ergonomic seat design, ensuring maximum comfort during extended mowing sessions. The easy-to-access controls and dashboard simplify operation, making it suitable for both novice and experienced users alike.

Maintenance is made straightforward with Troy-Bilt’s integrated maintenance reminders and easy-to-reach grease points for routine upkeep. The mower's mulch kit option allows for grass clippings to be finely chopped and returned to the lawn, promoting a healthier turf while saving time on clean-up.

Overall, the Troy-Bilt RZT combines powerful performance, advanced technology, and practical user-focused features to create a reliable riding mower. Whether managing a suburban lawn or a larger property, the RZT series proves to be a top contender for those seeking to maintain their outdoor space efficiently and effectively.