Woods Equipment MD80-2 manual Storage

Page 9

SAFETY RULES

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Do not modify or alter or permit anyone else to modify or alter the equipment or any of its compo- nents in any way.

Always wear relatively tight and belted clothing to avoid entanglement in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

Never go underneath equipment (lowered to the ground or raised) unless it is properly blocked and secured. Never place any part of the body under- neath equipment or between moveable parts even when the engine has been turned off. Hydraulic system leak down, hydraulic system failures, mechanical failures, or movement of control levers can cause equipment to drop or rotate unexpect- edly and cause severe injury or death. Follow Oper- ator's Manual instructions for working underneath and blocking requirements or have work done by a qualified dealer.

Make sure attachment is properly secured, adjusted, and in good operating condition.

Keep all persons away from operator control area while performing adjustments, service, or maintenance.

Make certain all movement of equipment com- ponents has stopped before approaching for ser- vice.

Frequently check blades. They should be sharp, free of nicks and cracks, and securely fastened.

Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

Make sure shields and guards are properly installed and in good condition. Replace if dam- aged.

Tighten all bolts, nuts and screws to torque chart specifications. Check that all cotter pins are installed securely to ensure equipment is in a safe condition before putting unit into service.

Make sure all safety decals are installed. Replace if damaged. (See Safety Decals section for location.)

Do not handle blades with bare hands. Careless or improper handling may result in serious injury.

Explosive separation of tire and rim parts can cause serious injury or death. Release all air pres- sure before loosening bolts.

STORAGE

Raise cutter and block securely. Block wheels and raise tongue with jack. Disconnect hydraulic lines to optional cylinder. Disconnect driveline and secure up off the ground.

Keep children and bystanders away from stor- age area.

Store on level, solid ground.

Follow manual instructions for storage.

(Rev. 5/11/2007)

D80 Safety Rules (Rev. 3/23/2007)

Safety 9

Image 9
Contents Rotary Cutter To the Dealer IntroductionLEA EL Instructivo Table of ContentsSpecifications Tractor RequirementsGeneral Information Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters--EnglishSafety Rules PreparationTraining Maintenance OperationTransportation Storage Serial Number Plate Safety & Instructional DecalsRED Rear Reflector To Avoid Serious Injury or DeathBe Careful Rotating Blades Thrown ObjectsOperation OperationTractor Stability Attaching Mounted Cutter to TractorShorten Driveline Driveline AttachmentCutting Height Adjustment Without Tailwheel or Check Chains Cutting Height Adjustment for MD80 Mounted CutterCutting Height Adjustment With Tailwheel or Check Chains Attaching PULL-TYPE Cutter to TractorPRE-OPERATION Check List Cutting Height Adjustment for D80 Pull- Type CutterStarting and Stopping Cutter Operating TechniqueUneven Terrain TipsOwners Service Owner ServiceLubrication Information Blade ServicingLubrication Points Blade RemovalBelt Installation Blade InstallationBlade Sharpening Chain ShieldingSplit Rim Tire Servicing Servicing Tires SafelyDealer Service Dealer ServiceGearbox Maintenance Gearbox Adjustment Gearbox AssemblyAssembly Blade Spindle RepairShield Bearing Service Joint DisassemblyUniversal Joint Repair Joint Assembly CD1389 Problem Possible Cause Solution Trouble ShootingAssembly AssemblyDistribution Baffle Installation Dealer SET-UP InstructionsGearbox Lubrication Chain Shielding InstallationWheel Yoke Installation Wheel Yoke Installation for D80-2 Pull-Type CutterTongue and H-Frame Assembly Tongue Installation for D80-2 Pull-Type CutterOptional Hydraulic Lift Assembly Optional Hydraulic Installation for D80-2 Pull-Type CutterDriveline Installation MD80 AssemblyOptional Leaf Mulcher Installation Optional Leaf Mulcher InstallationOptional Check Chain Installation Optional Check Chain InstallationDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListParts Index to Parts ListPart QTY Description D80-2 Main Frame Assembly PULL-TYPEMD80-2 Main Frame Assembly Mounted Model D80-2 & MD80-2 Main Frame Assembly Common Parts 15828 Complete Drive D80-2 Front 2/3 of 3-JOINT Drive Square ShaftD80-2 Front 2/3 of 3-JOINT Drive TWO-LOBE Shaft D80-2 & MD80-2 Rear Section of Universal Drive MD80-2 Front 1/2 of Universal DriveGearbox Repair Kit D80-2 & MD80-2 Gearbox AssemblyD80-2 & MD80-2 Blades D80-2 & MD80-2 Blade Spindle AssemblyD80-2 & MD80-2 Chain Shielding Assembly D80-2 Parking Jack D80-2 & MD80-2 Idler Pulley AssemblyD80-2 SPRING-LOADED Wheel Yoke D80-2 Height Adjustment CrankD80-2 Laminated Tire with HUB & Axle D80-2 RIM & Axle AssemblySOL ID T IRE D80-2 Aircraft Tire & HUBMD80-2 Tailwheel Assembly D80-2 Hydraulic Hose KIT & Fittings Optional D80-2 Pivot Link KIT OptionalD80-2 3-1/2 X 8 Hydraulic Cylinder #10475 Optional MD80-2 Check Chain Assembly Optional D80-2 & MD80-2 Leaf Mulcher Assembly OptionalMD80-2 Category 2 Bushing KIT MD80-2 Category 2 Hitch PIN OptionsSAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005 15914