Woods Equipment BW180XHDQ, BW126XHDQ manual 1000 RPM

Page 12
18865--C
15922-C

SAFETY & INSTRUCTIONAL DECALS

ATTENTION! BECOME ALERT! YOUR SAFETY IS INVOLVED!

Replace Immediately If Damaged!

WARNING

DO NOT EXCEED PTO SPEED OF

1000 RPM

PTO speeds higher than 1000 RPM can cause equipment failure and personal injury.

WARNING￿￿￿￿￿￿ ￿￿￿￿￿

￿￿￿ 540￿￿￿￿￿￿￿￿￿￿RPM￿ ￿￿￿"￿￿#￿￿￿￿￿$

￿￿￿￿￿￿￿￿￿ ￿￿￿￿!￿￿

18866-D

5- PN 15922 (1000 RPM)

OR

6- PN 18866 (540 RPM)

8 - PN 18864

DANGER

ROTATING DRIVELINE

CONTACT CAN CAUSE DEATH

KEEP AWAY!

DO NOT OPERATE WITHOUT -

All driveline guards, tractor and equipment shields in place

Drivelines securely attached at both ends

Driveline guards that turn freely on

driveline18864-C

7 - PN 15503

9 - PN 18865

WARNING

FALLING OFF CAN RESULT IN BEING RUN OVER.

„Tractor must be equipped with ROPS (or ROPS CAB) and seat belt. Keep foldable ROPS systems in “locked up” position at all times.

„Buckle Up! Keep seat belt securely fastened.

„Allow no riders.

RAISED EQUIPMENT CAN DROP AND CRUSH.

„Before working underneath, follow all instructions and safety rules in operator’s manual and securely block up all corners of equipment with jack stands.

„Securely blocking prevents equipment dropping from hydraulic leak- down, hydraulic system failures or mechanical component failures.

FALLING OFF OR FAILING TO BLOCK SECURELY CAN RESULT IN SERIOUS INJURY OR DEATH.

11 - PN 19924

DANGER

ROTATING BLADES AND

THROWN OBJECTS

Do not put hands or feet under or into mower when engine is running.

Before mowing, clear area of objects that may be thrown by blade.

Keep bystanders away.

Keep guards in place and in good condition.

BLADE CONTACT OR THROWN OBJECTS CAN CAUSE SERIOUS INJURY OR DEATH.

15503-C

19924-B

￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿WARNING￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿￿

Check for leaks with cardboard; never use hand.

Before loosening fittings: lower load, release pressure, and

￿be sure oil is cool.

Consult physician immediately if skin penetration occurs.

17 - PN 1004114

DANGER

If shaft connection is visible, shield is missing. Replace shield before

operating equipment.

1004114

12 Safety

MAN0963 (2/16/2012)

 

Image 12
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules InstallationTraining PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be Careful1000 RPM Safety Connecting Cutter to Tractor OperationOperation Cutting Height Adjustment Hydraulic ConnectionInterference Check CV Driveline Turning LimitsTractor Operation Cutter OperationMowing Tips ShreddingTransporting Lock-UpPRE-OPERATION Check List Owners ResponsibilityOwner Service Owner ServiceBlocking Method Lubrication Gearbox LubricationDriveline Lubrication Blade Installation Figure Seasonal LubricationBlades Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningCleaning Shielding RepairServicing Tires Safely Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Style a Seal Replacement FigureGearbox Repair Style a Gearbox Assembly Gearbox InstallationStyle a Gearbox Gearbox Maintenance Style B Seal InstallationDisassembly AssemblyGearbox Repair Style B Reinstallation Style B GearboxSplitter Gearbox Disassembly Splitter Gearbox AssemblySplitter Gearbox Repair Style a Splitter Gearbox Removal From CutterSplitter Gearbox Installation Splitter Gearbox InspectionSplitter Gearbox Repair Style B Reinstallation on Cutter Splitter Gearbox Style BCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Split Rim Tire ServicingAssembly Assembly InstructionsDealer SET-UP Instructions Install Height Adjustment Cylinder Install SMV Emblem Spring Arm and Cylinder InstallationInstall Wheel and Hub Install TongueInstall 3-Joint Drive 540 RPM Only Joint Drive InstallationInstall CV Drive Optional Install WingInstall Wing Cylinder & Lock-up Bar Install Wing Wheel and Hub Figure Left Wing Lock-Up Bar InstalledInstall Wing Wheel Yoke Adjustment Link Install Wing DrivelineInstall Hose Kit Install Chain or Belt Shielding Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing BW126XHD and BW126XHDL Counterweight Installation Counterweight InstallationWinch Kit Installation Optional Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0963 2/16/2012 Parts BW180XHD, BW180XHDQ BW126XHD, BW126XHDQMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Tire & hub see Wing Assembly REF Part QTY Description Style a Splitter Gearbox Assembly RPM 1000 RPMStyle B Splitter Gearbox Assembly Style a Wing & Center Gearbox Assembly Style a Wing & Center Gearbox Assembly Parts List CenterStyle B Wing & Center Gearbox Assembly Style B Wing & Center Gearbox Assembly Parts List Spring Wheel Yoke Assembly Optional For Right wing orCenter Deck Drive Assembly BW180X & BW126X Front Drive Assembly Equal Angle BW180X & BW126X Rear Drive Assembly Equal Angle RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly NC x 1-1/4 Carriage bolt GR5 1028590 Chain Shielding Center Section Front & Rear Single ROW Double ROWChain Shielding Wing Front & Rear Single ROWHydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITBW126XHD / BW126XHDQ Weight BOX Assembly Optional BW180XHD Shredder KIT 1033930 Optional Winch Kit Installation Winch KIT OptionalWinch Kit Operation Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty