Woods Equipment BW180XHDQ Install Wing Wheel and Hub Figure, Left Wing Lock-Up Bar Installed

Page 44

2.Slide spacer (53) and lock-up bar (16) over clevis pin (18) on back side of cylinder lug & secure with washer (108) and cotter pins (62).

3.Attach base end of wing cylinder (4) to cylinder links (19 & 20) using clevis pin (54) and cotter pins (62).

4.Remove plug from base end of hydraulic cylinder. Align cylinder rod end with cylinder lug on the wing and insert lock-up pin (22).

5.Slide spacer (21) over lock-up pin (22) on back side of cylinder rod and secure with cotter pins (62).

6.Insert safety pin (61) into the end of lock-up pin (22). The safety pin will secure lock-up bar into position when wing is in the UP position.

7.Extend cylinder fully & replace plug in base end of cylinder. This trapped air will help push wing down.

8.Install bushing (90), elbow, (69) and hose (59) to the rod end of cylinder (4). See Install Hose Kit, page 45 for complete instructions.

9.Repeat procedure for opposite wing.

NOTE: (BW126XHDR has only the right wing installed. BW126XHDL has only the left wing installed.)

19

20

16

 

 

 

18

 

 

 

62

 

53

 

 

 

 

 

DP3

16.

Wing Lock-Up Bar

20.

Cylinder Link

18.

1 x 4.08 Clevis Pin

53.

Spacer, 1"

19.

Cylinder Link

62.

1/4 x 1-1/2 Cotter

 

 

 

Pin

Figure 35. Left Wing Lock-Up Bar Installed

Install Wing Wheel and Hub (Figure 36)

1.Insert wheel hub into wing wheel yoke arms (5) and align holes.

2.Secure into position using cap screw (83) and flanged lock nut (88).

3.Attach wheel to hub using five lug nuts. Install the chamfered side of the lug nut toward the inside for steel rim for pneumatic tires and rims. Tighten to 75 lbs-ft. Check that tire air pressure is a maximum of 40 psi.

NOTE: Install the flat side of the nut toward the inside for solid tires and aircraft tires (shown).

4.Install optional dual wheel and hub to inside of wheel yoke arm.

NOTE: Pneumatic (BW180XHD and BW180XHDQ only), notat, and airplane tires are available for this cutter. See page 72 for parts list.

5.Wing wheel yoke arm, right

58. Wheel and hub

83.1/2 NC x 3 HHCS GR5

88.1/2 NC Flanged lock nut

Figure 36. Wing Wheel and Hub Installation - Right

44 Assembly

MAN0963 (2/16/2012)

 

 

Image 44
Contents Batwing Introduction To the DealerTable of Contents LEA EL InstructivoSpecifications General InformationFree Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishSafety Rules InstallationTraining PreparationTransportation OperationMaintenance Storage Safety & Instructional Decals Be Careful1000 RPM Safety Operation Connecting Cutter to TractorOperation Cutting Height Adjustment Hydraulic ConnectionInterference Check CV Driveline Turning LimitsTractor Operation Cutter OperationMowing Tips ShreddingTransporting Lock-UpPRE-OPERATION Check List Owners ResponsibilityBlocking Method Owner ServiceOwner Service Driveline Lubrication LubricationGearbox Lubrication Blade Installation Figure Seasonal LubricationBlades Blade Removal FigureSlip Clutch Adjustment Figure Blade SharpeningServicing Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Style a Seal Replacement FigureGearbox Repair Style a Gearbox Assembly Gearbox InstallationStyle a Gearbox Gearbox Maintenance Style B Seal InstallationGearbox Repair Style B DisassemblyAssembly Reinstallation Style B GearboxSplitter Gearbox Disassembly Splitter Gearbox AssemblySplitter Gearbox Repair Style a Splitter Gearbox Removal From CutterSplitter Gearbox Installation Splitter Gearbox InspectionSplitter Gearbox Repair Style B Reinstallation on Cutter Splitter Gearbox Style BCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Joint Assembly Split Rim Tire ServicingDealer SET-UP Instructions AssemblyAssembly Instructions Install Height Adjustment Cylinder Install SMV Emblem Spring Arm and Cylinder InstallationInstall Wheel and Hub Install TongueInstall 3-Joint Drive 540 RPM Only Joint Drive InstallationInstall Wing Cylinder & Lock-up Bar Install CV Drive OptionalInstall Wing Install Wing Wheel and Hub Figure Left Wing Lock-Up Bar InstalledInstall Hose Kit Install Wing Wheel Yoke Adjustment LinkInstall Wing Driveline Install Chain or Belt Shielding Chain Shielding Installation Center SectionChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing BW126XHD and BW126XHDL Counterweight Installation Counterweight InstallationWinch Kit Installation Optional Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0963 2/16/2012 Parts BW180XHD, BW180XHDQ BW126XHD, BW126XHDQMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Tire & hub see Wing Assembly REF Part QTY Description Style a Splitter Gearbox Assembly RPM 1000 RPMStyle B Splitter Gearbox Assembly Style a Wing & Center Gearbox Assembly Style a Wing & Center Gearbox Assembly Parts List CenterStyle B Wing & Center Gearbox Assembly Style B Wing & Center Gearbox Assembly Parts List Spring Wheel Yoke Assembly Optional For Right wing orCenter Deck Drive Assembly BW180X & BW126X Front Drive Assembly Equal Angle BW180X & BW126X Rear Drive Assembly Equal Angle RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly NC x 1-1/4 Carriage bolt GR5 1028590 Chain Shielding Center Section Front & Rear Single ROW Double ROWChain Shielding Wing Front & Rear Single ROWHydraulic Cylinders Crossbar Puller Optional Hydraulic Cylinder Stroke Control KITBW126XHD / BW126XHDQ Weight BOX Assembly Optional BW180XHD Shredder KIT 1033930 Optional Winch Kit Operation Winch Kit InstallationWinch KIT Optional Bolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Warranty