Woods Equipment BW180XHDQ, BW126XHDQ manual Seasonal Lubrication, Blades, Blade Removal Figure

Page 21

Seasonal Lubrication

In addition to the daily recommended lubrication, a more extensive application is recommended season- ally.

1.Fill CV double yokes with 20 pumps of grease with the joints in a straight line.

2.Articulate CV body to maximum angle several times to ensure full coverage of joints.

3.Place joints in the straight position and a add 10 additional pumps of grease to both joints.

4.Wipe telescoping drive clean of all old grease and contaminants.

5.Add a thin layer of new grease over telescoping drive.

BLADES

Before working underneath, read manual instructions, securely block up, and check stability. Secure blocking prevents equipment from drop- ping due to hydraulic leak down, hydraulic system failure, or mechanical component failure.

Blade Removal (Figure 6)

9.Blade pin

10.Crossbar assembly

11.Shim, 18 ga

12.Shim, 20 ga

13.Keyhole plate

14.Blade lock clip

52.1/2 NC x 1-1/4 HHCS GR5

Figure 6. Blade Assembly

1.Disconnect driveline from tractor PTO.

2.Raise cutter and block securely (see Figure 5).

3.Align crossbar (10) with blade access hole in the cutter frame. Remove cap screw (52), blade pin

lock clip (14), keyhole plate (13), and shims (11 & 12). Carefully drive blade pin (9) out of crossbar.

4.Rotate crossbar and repeat for opposite blade.

NOTICE

If blade pin (9) is seized in crossbar and extreme force will be needed to remove it, support crossbar from below to prevent gearbox damage.

Blade Installation (Figure 6)

CAUTION

Your dealer can supply genuine replacement blades. Substitute blades may not meet original equipment specifications and may be dangerous.

NOTICE

Crossbar rotation has clockwise rotation on left gearbox and counterclockwise rotation on the right and center gearboxes when looking down on cut- ter. Be sure to install blade cutting edge to lead in correct rotation.

NOTE: Always replace or sharpen both blades at the same time.

1.Inspect blade pin (9) for nicks or gouges, and if you find any replace the blade pin.

2.Insert blade pin through the blade. Blade should swivel on blade pin; if it doesn’t, determine the cause and correct.

3.Align crossbar (10) with blade access hole in cutter frame. Apply a liberal coating of Never-Seez® or equivalent to blade pin and crossbar hole. Make sure blade offset is down away from cutter.

4.Insert blade pin (9) through blade. Push blade pin through crossbar.

5.Install shims (11 & 12) over blade pin.

NOTE: Only use enough shims to allow keyhole plate (13) to slide into blade pin groove.

6.Install blade clip (14) over keyhole plate and into blade pin groove.

7.Secure into position with cap screw (52). Torque cap screw to 85 lbs-ft.

8.Repeat steps for opposite side.

NOTE: Blade should be snug but should swivel on pin without having to exert excessive force. Blade should not move more than a 1/4 inch up or down at the tip. Keep any spacers not used in the instal- lation as replacements or for future installation.

MAN0963 (2/16/2012)

Owner Service 21

 

 

Image 21
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishInstallation Safety RulesTraining PreparationOperation TransportationMaintenance Storage Be Careful Safety & Instructional Decals1000 RPM Safety Connecting Cutter to Tractor OperationOperation Hydraulic Connection Cutting Height AdjustmentInterference Check CV Driveline Turning LimitsCutter Operation Tractor OperationMowing Tips ShreddingLock-Up TransportingOwners Responsibility PRE-OPERATION Check ListOwner Service Owner ServiceBlocking Method Lubrication Gearbox LubricationDriveline Lubrication Seasonal Lubrication Blade Installation FigureBlades Blade Removal FigureBlade Sharpening Slip Clutch Adjustment FigureCleaning Shielding RepairServicing Tires Safely Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Style a Seal Replacement FigureGearbox Repair Style a Gearbox Installation Gearbox AssemblyStyle a Gearbox Seal Installation Gearbox Maintenance Style BDisassembly AssemblyGearbox Repair Style B Style B Gearbox ReinstallationSplitter Gearbox Assembly Splitter Gearbox DisassemblySplitter Gearbox Repair Style a Splitter Gearbox Removal From CutterSplitter Gearbox Inspection Splitter Gearbox InstallationSplitter Gearbox Repair Style B Splitter Gearbox Style B Reinstallation on CutterCrossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Split Rim Tire Servicing Joint AssemblyAssembly Assembly InstructionsDealer SET-UP Instructions Spring Arm and Cylinder Installation Install Height Adjustment Cylinder Install SMV EmblemInstall Tongue Install Wheel and HubJoint Drive Installation Install 3-Joint Drive 540 RPM OnlyInstall CV Drive Optional Install WingInstall Wing Cylinder & Lock-up Bar Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub FigureInstall Wing Wheel Yoke Adjustment Link Install Wing DrivelineInstall Hose Kit Chain Shielding Installation Center Section Install Chain or Belt ShieldingChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Counterweight Installation BW126XHD and BW126XHDL Counterweight InstallationWinch Kit Installation Optional Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0963 2/16/2012 BW180XHD, BW180XHDQ BW126XHD, BW126XHDQ PartsMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Tire & hub see Wing Assembly REF Part QTY Description RPM 1000 RPM Style a Splitter Gearbox AssemblyStyle B Splitter Gearbox Assembly Style a Wing & Center Gearbox Assembly Center Style a Wing & Center Gearbox Assembly Parts ListStyle B Wing & Center Gearbox Assembly Style B Wing & Center Gearbox Assembly Parts List For Right wing or Spring Wheel Yoke Assembly OptionalCenter Deck Drive Assembly BW180X & BW126X Front Drive Assembly Equal Angle BW180X & BW126X Rear Drive Assembly Equal Angle RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly NC x 1-1/4 Carriage bolt GR5 1028590 Single ROW Double ROW Chain Shielding Center Section Front & RearSingle ROW Chain Shielding Wing Front & RearHydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalBW126XHD / BW126XHDQ Weight BOX Assembly Optional BW180XHD Shredder KIT 1033930 Optional Winch Kit Installation Winch KIT OptionalWinch Kit Operation SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Warranty