Woods Equipment BW180XHDQ, BW126XHDQ manual Install Wheel and Hub, Install Tongue

Page 41

Install Wheel and Hub

1.Insert wheel hub into outside of wheel yoke arm (1) and align holes.

2.Secure into position using cap screw (83) and flanged lock nut (88).

3.Attach wheel to hub using five lug nuts. Install the chamfered side of the lug nut toward the inside for steel rim for pneumatic tires and rims. Tighten to 75 lbs-ft. Check that tire air pressure is a maximum of 40 psi.

NOTE: Install the flat side of the nut toward the inside for solid tires and aircraft tires (shown).

4.Install optional dual wheel and hub to inside of wheel yoke arm.

NOTE: Pneumatic (BW180XHD and BW180XHDQ only), notat, and airplane tires are available for this cutter. See page 72 for parts list.

1.Center Wheel Yoke Arm

83. 1/2" NC x 3" HHCS GR5

88. 1/2" NC Flange Lock Nut

Figure 29. Center Section Wheel and

Hub Installation

Install Tongue

1.Attach tongue (22) to center section using two tongue pivot pins (37) and cotter pins (60).

2.Attach attitude rod (6) to lug on tongue and secure with clevis pin (41), washer (107), and cotter pin (62).

3.Attach parking jack (21) to the side of the tongue.

4.Attach safety chain (8) to the bottom of center gusset and secure with cap screw (97), washer (100), and lock nut (102).

6.Attitude Rod

8.Safety Chain

21.Parking Jack

22.Tongue

37.Tongue Pivot Pin

41.Clevis Pin, 1" x 2.26"

60.3/16 x 1-1/2 Cotter Pin

62.1/4 x 1-1/2 Cotter Pin

97.3/4 NC x 2-1/4 Hex Head Cap Screw 100.3/4 x 2 x 3/8 Flat Washer

102.3/4 NC Lock Nut 107.1" Flat Washer

Figure 30. Tongue Installation

MAN0963 (2/16/2012)

Assembly 41

 

 

Image 41
Contents Batwing To the Dealer IntroductionLEA EL Instructivo Table of ContentsGeneral Information SpecificationsSafety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishInstallation Safety RulesTraining PreparationOperation TransportationMaintenance Storage Be Careful Safety & Instructional Decals1000 RPM Safety Operation Connecting Cutter to TractorOperation Hydraulic Connection Cutting Height AdjustmentInterference Check CV Driveline Turning LimitsCutter Operation Tractor OperationMowing Tips ShreddingLock-Up TransportingOwners Responsibility PRE-OPERATION Check ListBlocking Method Owner ServiceOwner Service Driveline Lubrication LubricationGearbox Lubrication Seasonal Lubrication Blade Installation FigureBlades Blade Removal FigureBlade Sharpening Slip Clutch Adjustment FigureServicing Tires Safely CleaningShielding Repair Troubleshooting TroubleshootingDealer Service Dealer ServiceGearbox Maintenance Style a Seal Replacement FigureGearbox Repair Style a Gearbox Installation Gearbox AssemblyStyle a Gearbox Seal Installation Gearbox Maintenance Style BGearbox Repair Style B DisassemblyAssembly Style B Gearbox ReinstallationSplitter Gearbox Assembly Splitter Gearbox DisassemblySplitter Gearbox Repair Style a Splitter Gearbox Removal From CutterSplitter Gearbox Inspection Splitter Gearbox InstallationSplitter Gearbox Repair Style B Splitter Gearbox Style B Reinstallation on CutterCrossbar Removal Crossbar RemovalUniversal Joint Repair Crossbar InstallationJoint Disassembly Split Rim Tire Servicing Joint AssemblyDealer SET-UP Instructions AssemblyAssembly Instructions Spring Arm and Cylinder Installation Install Height Adjustment Cylinder Install SMV EmblemInstall Tongue Install Wheel and HubJoint Drive Installation Install 3-Joint Drive 540 RPM OnlyInstall Wing Cylinder & Lock-up Bar Install CV Drive OptionalInstall Wing Left Wing Lock-Up Bar Installed Install Wing Wheel and Hub FigureInstall Hose Kit Install Wing Wheel Yoke Adjustment LinkInstall Wing Driveline Chain Shielding Installation Center Section Install Chain or Belt ShieldingChain Shielding Installation Right Wing Shown Belt Shielding Installation Right Wing Counterweight Installation BW126XHD and BW126XHDL Counterweight InstallationWinch Kit Installation Optional Dealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListMAN0963 2/16/2012 BW180XHD, BW180XHDQ BW126XHD, BW126XHDQ PartsMain Frame Assembly Front Section Part QTY Description Main Frame Assembly Rear Section Tire & hub see Wing Assembly REF Part QTY Description RPM 1000 RPM Style a Splitter Gearbox AssemblyStyle B Splitter Gearbox Assembly Style a Wing & Center Gearbox Assembly Center Style a Wing & Center Gearbox Assembly Parts ListStyle B Wing & Center Gearbox Assembly Style B Wing & Center Gearbox Assembly Parts List For Right wing or Spring Wheel Yoke Assembly OptionalCenter Deck Drive Assembly BW180X & BW126X Front Drive Assembly Equal Angle BW180X & BW126X Rear Drive Assembly Equal Angle RPM & 1000 RPM Front CV Drive Wing Drive Assembly Bolt Wheel & Tire Assembly NC x 1-1/4 Carriage bolt GR5 1028590 Single ROW Double ROW Chain Shielding Center Section Front & RearSingle ROW Chain Shielding Wing Front & RearHydraulic Cylinders Hydraulic Cylinder Stroke Control KIT Crossbar Puller OptionalBW126XHD / BW126XHDQ Weight BOX Assembly Optional BW180XHD Shredder KIT 1033930 Optional Winch Kit Operation Winch Kit InstallationWinch KIT Optional SAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Warranty