Woods Equipment BB84X, BB60X Top Link Adjustment BB48X Only, Quick Hitch Attachment BB48X Only

Page 13

3.Adjust the tractor lower 3-point arm anti-sway devices to prevent cutter from swinging side to side during transport.

4.Adjust tractor drawbar so that it will not interfere with cutter or driveline.

Top Link Adjustment - BB48X Only

(Figure 2)

1.Tractor top link

2.Cutter top link mounting pin

3.Floating link

4.Cutter hitch pin

5.A-Frame bars

6.Tractor top link bracket

Figure 2. Top Link Adjustment - BB48X Only

1.Attach tractor top link (1), to lowest hole provided in the tractor’s top link bracket (6).

2.Attach rear portion of tractor top link to the first hole on the cutter floating link (3). Select a top link mounting pin that will allow the floating link to swing freely through the cutter A-frame bars (5).

3.Raise cutter to transport position and adjust tractor top link until cutter is level in the raised position.

NOTE: If you cannot level the cutter using the low- est hole in the tractor’s top link bracket, move top link to the next hole and level the cutter.

Quick Hitch Attachment - BB48X Only

(Figure 3)

1.Remove brace arms (6), floating link (3), cap screw (11), spacer (7), and flange lock nut (9) from upper hole on A-frame bars (5) as shown on left in Figure 3.

NOTE: A-Frame bars are installed to mast plates with carriage bolts through the square holes.

2.Attach open end of floating link (3) to the bottom hole of A-frame bars (5). Secure using cap screw (11), sleeve (10), and flange lock nut (9) as shown on right in Figure 3.

3.Attach closed end of floating link (3) to diagonal braces (6). Secure using cap screw (8), spacer (7), and flange lock nut (9) supplied in hardware bag.

NOTE: Quick hitch top hook will pick up on sleeve (10). Lower quick hitch hook will attach to cutter hitch pins.

4.Raise cutter to transport position and adjust tractor top link until cutter is level in the raised position.

3.

Floating link

8.

1/2 NC x 4 Cap screw

 

5.

A-frame

9.

1/2 NC Flange lock nut

BB48X

6.

Diagonal braces

10.

1/2 x 3/4 x 2-13/16 Sleeve

7.

1/2 x 2-3/4 Spacer

11.

1/2 NC x 5 Cap screw

 

Figure 3. Standard Hitch and Quick Hitch Configurations - BB48X Only

(Rev. 4/24/2009) MAN0632 (5/15/2007)

Operation 13

Image 13
Contents Brushbulltm To the Dealer IntroductionTo the Owner Table of Contents General Information SpecificationsBB48X BB60X BB72X BB84X Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishWoods Equipment Company Training Safety RulesPreparation OperationMaintenance Storage Serial Number Plate Safety & Instructional DecalsRED Rear Reflector Crushing and Pinching Hazard Be CarefulOperation OperationTractor Stability Attaching Cutter to Tractor BB48X onlyQuick Hitch Attachment BB48X Only Top Link Adjustment BB48X OnlyAttaching Cutter to Tractor BB60X, BB72X, BB84X only Installation and Removal Driveline Tractor PTOShortening Driveline Driveline AttachmentDriveline Interference Check Cutting Height AdjustmentShredding Material Operating Technique Check Chain AdjustmentPRE-OPERATION Check List Owner Service Owner ServiceBlocking Method Lubrication InformationBlade Servicing Blade Installation FigureBlade Removal Figure Blade Sharpening Slip Clutch AdjustmentComer Walterscheid BB84X OnlyModel WalterscheidCleaning Driveline Shear Bolt ReplacementShielding Repair Problem Possible Cause Solution TroubleshootingMowing Conditions Dealer Service Dealer ServiceGearbox Maintenance Seal ReplacementVertical Shaft Seal Repair Seal RepairHorizontal Seal Leak Repair Gearbox RepairReassemble Gearbox Reinstall GearboxBB48X, BB60X, BB72X BB72X S/N 1159929 and Above only On CAST/CROWN TOP BB48X, BB60XReassemble Gearbox Cast Top BB48X Reassemble Gearbox Cast Top BB60X and BB72X Crossbar Removal Crossbar RemovalJoint Disassembly Crossbar InstallationUniversal Joint Repair Install Cups Joint AssemblyDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListDealer Check Lists Assembly AssemblyDealer SET-UP Instructions Disassemble Shipping Unit Figure BB60X, BB72X & BB84X Shipping ConfigurationInstall A-FRAME to Diagonal Brace Bars Install A-FRAMEBB48X BB60X, BB72X & BB84XInstall Dual Tailwheel BB84XD Optional Install TailwheelBB48X Standard Hitch Set-Up BB48X Quick Hitch Set-UpBB60X, BB72X & BB84X Standard & Quick Hitch Set-Up Install DrivelineShear Bolt Driveline BB48X & BB60X Only Driveline Slip Clutch Optional on BB48X & BB60XDriveline Slip Clutch BB72X and BB84X Install Safety ShieldingRubber Deflector Standard Fill GearboxBB60X BB72X Install Optional Check ChainsBB84X Parts Parts Index BrushbulltmBB48X, BB60X, BB72X & BB84X BB84X Shown Brushbull STANDARD-DUTY Main AssemblyBB72X, BB84X BB48X, BB60X, BB72X & BB84X Main Assembly Parts ListGearbox repair asy BB72X S/N 1159928 and Below Gearbox Assembly Flat TOPCheck Chain Assembly Optional Gearbox Assembly Parts ListBB48X Gearbox Assembly CAST/CROWN TOP BB48X Comer Standard Driveline Assembly BB60X Comer Standard Driveline Assembly BB48X & BB60X Comer Slip Clutch Driveline Assembly Optional BB72X Comer Slip Clutch Driveline Assembly Series 50 Series BB84X Comer Slip Clutch Driveline AssemblyBB84X Walterscheid Slip Clutch Driveline Assembly Front Rubber Shielding Standard Front & Rear Chain Shielding OptionalSAE Series Torque Chart Bolt Torque ChartAppendix Metric SeriesAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005