Woods Equipment BB48X manual BB60X, BB72X & BB84X Standard & Quick Hitch Set-Up, Install Driveline

Page 40

BB60X, BB72X & BB84X Standard & Quick Hitch Set-Up

1.Leave A-frame and top link attached together.

2.Remove bolt (60), spacer (10) and nut (12) from front hole in brace bar (7).

3.Assemble top link to brace bar with previous hardware as shown in Figure 37.

BB60X, BB72X & BB84X

STANDARD HITCH &

QUICK HITCH

6.A-Frame bar

7.Diagonal brace bar

8.Sleeve, .75 x 1.25 x 3.0

9.Top link

10.Sleeve, .626 x 1.00 x 1.26

12.5/8 NC Flanged lock nut

18.3/4 NC x 5-1/2 Cap screw

20.3/4 NC Lock nut

60.5/8 NC x 2-3/4 Cap screw

Figure 37. Diagonal Brace Bars to A-Frame Connection - BB60X, BB72X & BB84X

INSTALL DRIVELINE

On BB48X or BB60X, select either the standard shear bolt or optional slip clutch driveline.

Shear Bolt Driveline -

BB48X & BB60X Only

NOTICE

A grade 2 bolt must be used for the shear bolt to provide gearbox protection.

1.Remove rear drive shield (1) from driveline.

2.Position clutch shield (5) against gearbox. Secure using cap screw (7), lock washers (8), and flat washers (9). Torque hardware to 12 lbs-ft.

3.To prevent seal damage, carefully push driveline onto gearbox input shaft until it contacts the gearbox housing.

4.Place retaining ring (6) in slot on input shaft and snap into place.

5.Align the holes in the driveline yoke and gearbox input shaft. Install and tighten shear bolt (4) and nut (3).

6.Install rear drive shield to driveline.

7.Lubricate rear driveline half and install front driveline half.

8.Attach tether chain to diagonal brace bar.

1.Driveline shield

2.Input shaft (slot)

3.1/2 NC Lock nut

4.1/2 NC x 3 Cap screw GR2 (Shear Bolt)

5.Clutch shield

6.Retaining ring

7.M8 x 1.25P x 20 mm Cap screw

8.5/16 Lock washer

9.5/16 Flat washer

Figure 38. Shear Bolt Driveline Assembly

(BB48X & BB60X Standard)

Driveline Slip Clutch -

Optional on BB48X & BB60X

NOTICE

A grade 8 bolt must be used to attach clutch driveline to gearbox.

A new slip clutch, or one that has been in storage over the winter, may seize.

1.Before operating slip clutch, make sure it will slip. Refer to Slip Clutch Adjustment, page 20.

2.Position clutch shield (3) against gearbox. Secure using cap screw (4), lock washers (5), and flat washers (6). Torque hardware to 12 lbs-ft.

40Assembly

(Rev. 5/10/2009) MAN0632 (5/15/2007)

Image 40
Contents Brushbulltm To the Dealer IntroductionTo the Owner Table of Contents General Information SpecificationsBB48X BB60X BB72X BB84X Free Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English/Spanish Training Package for Rotary Mowers/Cutters-EnglishWoods Equipment Company Safety Rules TrainingPreparation OperationMaintenance Storage Serial Number Plate Safety & Instructional DecalsRED Rear Reflector Be Careful Crushing and Pinching HazardOperation OperationTractor Stability Attaching Cutter to Tractor BB48X onlyTop Link Adjustment BB48X Only Quick Hitch Attachment BB48X OnlyInstallation and Removal Driveline Tractor PTO Attaching Cutter to Tractor BB60X, BB72X, BB84X onlyDriveline Attachment Shortening DrivelineDriveline Interference Check Cutting Height AdjustmentShredding Material Operating Technique Check Chain AdjustmentPRE-OPERATION Check List Owner Service Owner ServiceBlocking Method Lubrication InformationBlade Servicing Blade Installation FigureBlade Removal Figure Slip Clutch Adjustment Blade SharpeningComer Walterscheid BB84X OnlyWalterscheid ModelCleaning Driveline Shear Bolt ReplacementShielding Repair Problem Possible Cause Solution TroubleshootingMowing Conditions Dealer Service Dealer ServiceGearbox Maintenance Seal ReplacementSeal Repair Vertical Shaft Seal RepairHorizontal Seal Leak Repair Gearbox RepairReinstall Gearbox Reassemble GearboxBB48X, BB60X, BB72X On CAST/CROWN TOP BB48X, BB60X BB72X S/N 1159929 and Above onlyReassemble Gearbox Cast Top BB48X Reassemble Gearbox Cast Top BB60X and BB72X Crossbar Removal Crossbar RemovalJoint Disassembly Crossbar InstallationUniversal Joint Repair Joint Assembly Install CupsDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListDealer Check Lists Assembly AssemblyDealer SET-UP Instructions BB60X, BB72X & BB84X Shipping Configuration Disassemble Shipping Unit FigureInstall A-FRAME Install A-FRAME to Diagonal Brace BarsBB48X BB60X, BB72X & BB84XInstall Tailwheel Install Dual Tailwheel BB84XD OptionalBB48X Standard Hitch Set-Up BB48X Quick Hitch Set-UpInstall Driveline BB60X, BB72X & BB84X Standard & Quick Hitch Set-UpShear Bolt Driveline BB48X & BB60X Only Driveline Slip Clutch Optional on BB48X & BB60XInstall Safety Shielding Driveline Slip Clutch BB72X and BB84XRubber Deflector Standard Fill GearboxBB60X BB72X Install Optional Check ChainsBB84X Parts Index Brushbulltm PartsBrushbull STANDARD-DUTY Main Assembly BB48X, BB60X, BB72X & BB84X BB84X ShownBB48X, BB60X, BB72X & BB84X Main Assembly Parts List BB72X, BB84XGearbox Assembly Flat TOP Gearbox repair asy BB72X S/N 1159928 and BelowCheck Chain Assembly Optional Gearbox Assembly Parts ListBB48X Gearbox Assembly CAST/CROWN TOP BB48X Comer Standard Driveline Assembly BB60X Comer Standard Driveline Assembly BB48X & BB60X Comer Slip Clutch Driveline Assembly Optional BB72X Comer Slip Clutch Driveline Assembly BB84X Comer Slip Clutch Driveline Assembly Series 50 SeriesBB84X Walterscheid Slip Clutch Driveline Assembly Front & Rear Chain Shielding Optional Front Rubber Shielding StandardBolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005