Woods Equipment BB72X, BB48X, BB60X manual Install Tailwheel, Install Dual Tailwheel BB84XD Optional

Page 39

INSTALL TAILWHEEL

1.Attach tailwheel bracket (6) to cutter at the tailwheel pivot holes (5B) using cap screw (13) and flange lock nut (14) previously removed.

NOTE: Make sure grease fitting on tube is on top when installing tailwheel.

2.Select desired height adjustment holes (10), and secure tailwheel bracket with cap screws (13) and flange lock nuts (14). Cutting height adjustment will be necessary when cutter is fully assembled. See page 16.

3.Raise rear of cutter and insert tailwheel assembly

(9)into tailwheel bracket (6). Secure with washer

(37)and spiral pin (28).

4.Place diagonal brace bars (4) on the inside of frame rails and attach to diagonal brace mounting holes (5A). Secure using cap screws (13) and flange lock nuts (14).


	4.	Diagonal brace bar	10.	Cutting height
	5A.	Diagonal brace		bracket
		mounting hole	13.	5/8 NC x 2 HHCS
	5B.	Tailwheel pivot hole	14.	5/8 NC Flange nut
	6.	Tailwheel bracket	28.	Spirol pin
	9.	Tailwheel assembly	37.	33 mm Flat washer

Figure 35. Tailwheel Installation

INSTALL DUAL TAILWHEEL

BB84XD (OPTIONAL)

1.Attach dual tailwheel (1) to main frame (2) using position 5B and desired height adjustment holes as shown in Figure 36.

2.Secure with cap screws (3) and hex nuts (4).

3.Torque hardware to 175 lbs-ft.

1. Dual tailwheel

2. Deck, BB84XD

3. 5/8 NC x 2-1/2 HHCS

4. 5/8 Flange lock nut

Figure 36. Dual Tailwheel Installation

BB48X Standard Hitch Set-Up

1.Remove cap screw (18), upper Figure 34, and flange lock nut (20) from top hole on A-frame bars. Leave spacer (8) and float link (9) together.

2.Position diagonal brace bars (7) on the outside of A-frame bars (6).

3.Align diagonal brace bars with top hole in A-frame bars, float link, and spacer. Secure with cap screw (18) and flange lock nut (20) that were previously removed.

BB48X Quick Hitch Set-Up

An optional Quick Hitch attachment may be used on this cutter. Install A-frame as shown (Figure 34, bot- tom).

(Rev. 5/10/2009) MAN0632 (5/15/2007)

Assembly 39

Image 39

Contents Brushbulltm Introduction To the DealerTo the Owner Table of Contents Specifications General InformationBB48X BB60X BB72X BB84X Safety Free Mower Safety VideoTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishWoods Equipment Company Operation Safety RulesTraining PreparationMaintenance Storage Safety & Instructional Decals Serial Number PlateRED Rear Reflector Crushing and Pinching Hazard Be CarefulAttaching Cutter to Tractor BB48X only OperationOperation Tractor StabilityQuick Hitch Attachment BB48X Only Top Link Adjustment BB48X OnlyAttaching Cutter to Tractor BB60X, BB72X, BB84X only Installation and Removal Driveline Tractor PTOShortening Driveline Driveline AttachmentCutting Height Adjustment Driveline Interference CheckShredding Material Check Chain Adjustment Operating TechniquePRE-OPERATION Check List Lubrication Information Owner ServiceOwner Service Blocking MethodBlade Installation Figure Blade ServicingBlade Removal Figure Walterscheid BB84X Only Slip Clutch AdjustmentBlade Sharpening ComerModel WalterscheidDriveline Shear Bolt Replacement CleaningShielding Repair Troubleshooting Problem Possible Cause SolutionMowing Conditions Seal Replacement Dealer ServiceDealer Service Gearbox MaintenanceGearbox Repair Seal RepairVertical Shaft Seal Repair Horizontal Seal Leak RepairReassemble Gearbox Reinstall GearboxBB48X, BB60X, BB72X BB72X S/N 1159929 and Above only On CAST/CROWN TOP BB48X, BB60XReassemble Gearbox Cast Top BB48X Reassemble Gearbox Cast Top BB60X and BB72X Crossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Install Cups Joint AssemblyDelivery Check List Dealer Check ListsDealer Check Lists PRE-DELIVERY Check ListDealer Check Lists Assembly AssemblyDealer SET-UP Instructions Disassemble Shipping Unit Figure BB60X, BB72X & BB84X Shipping ConfigurationBB60X, BB72X & BB84X Install A-FRAMEInstall A-FRAME to Diagonal Brace Bars BB48XBB48X Quick Hitch Set-Up Install TailwheelInstall Dual Tailwheel BB84XD Optional BB48X Standard Hitch Set-UpDriveline Slip Clutch Optional on BB48X & BB60X Install DrivelineBB60X, BB72X & BB84X Standard & Quick Hitch Set-Up Shear Bolt Driveline BB48X & BB60X OnlyFill Gearbox Install Safety ShieldingDriveline Slip Clutch BB72X and BB84X Rubber Deflector StandardInstall Optional Check Chains BB60X BB72XBB84X Parts Parts Index BrushbulltmBB48X, BB60X, BB72X & BB84X BB84X Shown Brushbull STANDARD-DUTY Main AssemblyBB72X, BB84X BB48X, BB60X, BB72X & BB84X Main Assembly Parts ListGearbox repair asy BB72X S/N 1159928 and Below Gearbox Assembly Flat TOPGearbox Assembly Parts List Check Chain Assembly OptionalBB48X Gearbox Assembly CAST/CROWN TOP BB48X Comer Standard Driveline Assembly BB60X Comer Standard Driveline Assembly BB48X & BB60X Comer Slip Clutch Driveline Assembly Optional BB72X Comer Slip Clutch Driveline Assembly Series 50 Series BB84X Comer Slip Clutch Driveline AssemblyBB84X Walterscheid Slip Clutch Driveline Assembly Front Rubber Shielding Standard Front & Rear Chain Shielding OptionalMetric Series Bolt Torque ChartSAE Series Torque Chart AppendixAbbreviations Bolt Size ChartIndex IndexWarranty Rev /23/2005