Woods Equipment BB48X, BB84X, BB60X, BB72X manual Assembly, Dealer SET-UP Instructions

Page 36

ASSEMBLY

DEALER SET-UP INSTRUCTIONS

Assembly of this cutter is the responsibility of the Woods dealer. It should be delivered to the owner com- pletely assembled, lubricated, and adjusted for normal cutting conditions.

The cutter is shipped partially assembled. Assembly will be easier if aligned and loosely assembled before tightening hardware. Recommended torque values for hardware are located in the Bolt Torque Chart, page 56.

Complete Dealer Check Lists, page 34 when you have completed the assembly.

be stopped when anyone comes within 300 feet (92 m).

•This shielding is designed to reduce the risk of thrown objects. The mower deck and protec- tive devices cannot prevent all objects from escaping the blade enclosure in every mowing condition. It is possible for objects to ricochet and escape, traveling as much as 300 feet (92 m).

Make sure attachment is properly secured, adjusted, and in good operating condition.

CAUTION

Full chain, rubber, or steel band shielding must be installed when operating in populated areas or other areas where thrown objects could injure peo- ple or damage property.

•If this machine is not equipped with full chain, rubber, or steel band shielding, operation must

Always wear relatively tight and belted clothing to avoid getting caught in moving parts. Wear sturdy, rough-soled work shoes and protective equipment for eyes, hair, hands, hearing, and head; and respirator or filter mask where appropriate.

1.Mounting pin hardware

2.A-Frame bar

3.Upper mounting hardware (under clutch shield)

4.Diagonal brace

5A. Diagonal brace bar

mounting hole

5B. Tailwheel pivot hole

6.Tailwheel bracket

7.PTO Hanger

9.Tailwheel

10.Height adjustment

12.Bag of hardware

13.Driveline (Shear bolt)

14.Clutch shield

	2	6
		6
	14	3
	14
	4
9		10
		10
7		5B
		5B
		5A
1
	13

Figure 30. BB48X Shipping Configuration

36Assembly

(Rev. 4/24/2009) MAN0632 (5/15/2007)

Image 36

Contents Brushbulltm Introduction To the DealerTo the Owner Table of Contents Specifications General InformationBB48X BB60X BB72X BB84X Free Mower Safety Video SafetyTraining Package for Rotary Mowers/Cutters-English Training Package for Rotary Mowers/Cutters-English/SpanishWoods Equipment Company Safety Rules TrainingPreparation OperationMaintenance Storage Safety & Instructional Decals Serial Number PlateRED Rear Reflector Be Careful Crushing and Pinching HazardOperation OperationTractor Stability Attaching Cutter to Tractor BB48X onlyTop Link Adjustment BB48X Only Quick Hitch Attachment BB48X OnlyInstallation and Removal Driveline Tractor PTO Attaching Cutter to Tractor BB60X, BB72X, BB84X onlyDriveline Attachment Shortening DrivelineCutting Height Adjustment Driveline Interference CheckShredding Material Check Chain Adjustment Operating TechniquePRE-OPERATION Check List Owner Service Owner ServiceBlocking Method Lubrication InformationBlade Installation Figure Blade ServicingBlade Removal Figure Slip Clutch Adjustment Blade SharpeningComer Walterscheid BB84X OnlyWalterscheid ModelDriveline Shear Bolt Replacement CleaningShielding Repair Troubleshooting Problem Possible Cause SolutionMowing Conditions Dealer Service Dealer ServiceGearbox Maintenance Seal ReplacementSeal Repair Vertical Shaft Seal RepairHorizontal Seal Leak Repair Gearbox RepairReinstall Gearbox Reassemble GearboxBB48X, BB60X, BB72X On CAST/CROWN TOP BB48X, BB60X BB72X S/N 1159929 and Above onlyReassemble Gearbox Cast Top BB48X Reassemble Gearbox Cast Top BB60X and BB72X Crossbar Removal Crossbar RemovalCrossbar Installation Joint DisassemblyUniversal Joint Repair Joint Assembly Install CupsDealer Check Lists Dealer Check ListsPRE-DELIVERY Check List Delivery Check ListDealer Check Lists Assembly AssemblyDealer SET-UP Instructions BB60X, BB72X & BB84X Shipping Configuration Disassemble Shipping Unit FigureInstall A-FRAME Install A-FRAME to Diagonal Brace BarsBB48X BB60X, BB72X & BB84XInstall Tailwheel Install Dual Tailwheel BB84XD OptionalBB48X Standard Hitch Set-Up BB48X Quick Hitch Set-UpInstall Driveline BB60X, BB72X & BB84X Standard & Quick Hitch Set-UpShear Bolt Driveline BB48X & BB60X Only Driveline Slip Clutch Optional on BB48X & BB60XInstall Safety Shielding Driveline Slip Clutch BB72X and BB84XRubber Deflector Standard Fill GearboxInstall Optional Check Chains BB60X BB72XBB84X Parts Index Brushbulltm PartsBrushbull STANDARD-DUTY Main Assembly BB48X, BB60X, BB72X & BB84X BB84X ShownBB48X, BB60X, BB72X & BB84X Main Assembly Parts List BB72X, BB84XGearbox Assembly Flat TOP Gearbox repair asy BB72X S/N 1159928 and BelowGearbox Assembly Parts List Check Chain Assembly OptionalBB48X Gearbox Assembly CAST/CROWN TOP BB48X Comer Standard Driveline Assembly BB60X Comer Standard Driveline Assembly BB48X & BB60X Comer Slip Clutch Driveline Assembly Optional BB72X Comer Slip Clutch Driveline Assembly BB84X Comer Slip Clutch Driveline Assembly Series 50 SeriesBB84X Walterscheid Slip Clutch Driveline Assembly Front & Rear Chain Shielding Optional Front Rubber Shielding StandardBolt Torque Chart SAE Series Torque ChartAppendix Metric SeriesBolt Size Chart AbbreviationsIndex IndexWarranty Rev /23/2005