Shindaiwa 80974 manual Long Term Storage, Blade Sharpening, Shindaiwa Tornado Blade, Maintenance

Page 15
Long Term Storage

Long Term Storage

Whenever the unit will not be used for 30 days or longer, use the following procedures to prepare it for storage:

Clean external parts thoroughly.

Drain all the fuel from the fuel tank.

IMPORTANT!

All stored fuels should be stabilized with a fuel stabilizer such as STA-BIL™ , if Blade Sharpening oil with fuel stabilizer is not used.

To remove the remaining fuel from the fuel lines and carburetor and with the fuel drained from the fuel tank.

1.Prime the primer bulb until no more fuel is passing through.

2.Start and run the engine until stops running.

3.Repeat steps 1 and 2 until the engine will no longer start.

CAUTION!

Gasoline stored in the carburetor for extended periods can cause hard start- ing and could also lead to increased service and maintenance costs.

Remove the spark plug and pour about 1/4 ounce of 2-cycle mixing oil into the cylinder through the spark plug hole.

Slowly pull the recoil starter 2 or 3 times so oil will evenly coat the interior of the engine. Reinstall the spark plug.

Before storing the unit, repair or re- place any worn or damaged parts.

Remove the air cleaner element from the carburetor and clean it thoroughly with soap and water. Let dry before reinstalling the element.

Store the unit in a clean, dust-free area.

Blade Sharpening

When the blade’s cutting edges become slightly dull, they can be re- sharpened with a few strokes of a file. In order to keep the blade in balance, all cutting edges must be sharpened equally.

Shindaiwa TornadoBlade

To sharpen the cutters on a Shindaiwa Tornado Blade, use a 7/32-inch round file. File the leading edge of each tooth to a razor edge. The top plate of each tooth should angle back 30°.

Shindaiwa Tornado BladeWARNING!

Sharpen the cutting teeth only. DO NOT alter the contour of the blade in any way.

Round

File

Filing Direction

30°

Figure 32

Multiple-tooth Circular Blade

Use a round file to maintain a radius of 0.04 to 0.06" (1 to 1.5 mm) at the base of each tooth. Cutting edges must be offset equally on each side.

Round

File

Filing Direction

MAINTENANCE

Figure 33

15

Image 15
Contents SHINDAIWA OWNER’S/OPERATORS MANUAL T272 TRIMMER T272X TRIMMEREspanol pg. SP1-SP20Introduction ContentsGeneral Safety Instructions SAFETYGeneral Safety Instructions The Properly Equipped Operator Be Aware of the Working EnvironmentFEET life, and safer operation Safety LabelsProduct Description your unit and its various compo6.7kg/14.8 pounds Assembly and Adjustments Handle T272/T272XSpecifications T272X/C272 6.7kg/14.7 poundsTo Change Position of Line Cutter Adjusting Throttle Level Free Play T272/T272XAssembly and Adjustments Cutting Attachment Shield T272/T272X Install the Cutting Attachment ShieldInstalling a Trimmer Head T272X Installing a Trimmer Head T272ASSEMBLY Assembly and Adjustments Installing a Blade T272XMixing Fuel Filling the Fuel TankStarting the Engine When the Engine Starts Engine Idle AdjustmentStarting the Engine continued Stopping the EngineCutting Grass-Units equipped with a trimmer head Check Unit ConditionShoulder Strap T272X T272Using A Brushcutter Blade T272X 10/15 hour Maintenance General MaintenanceDaily Maintenance 10 hour Maintenance50 hour Maintenance 135-hour MaintenanceEvery 135 hours of operation, re- move and clean the muffler Multiple-tooth Circular Blade Long Term StorageBlade Sharpening Shindaiwa Tornado BladeTROUBLESHOOTING Troubleshooting GuideLOW POWER OUTPUT Troubleshooting Guide continuedTROUBLESHOOTING ADDITIONAL PROBLEMSEmission System Warranty Statement 2004 Shindaiwa, Inc Part Number Revision 11/04 Shindaiwa is a registered trademark of Shindaiwa, IncSpecifications subject to change without notice PODADORA T272 PODADORA T272X Manual Del Propietario/Operador ShindaiwaNumero de part 80974 Rev. 11/04 Instrucciones Generales de Seguridad IntroducciónCONTENIDO Declaraciones De SeguridadEl Operario Debidamente Equipado Esté Alerta del Area de TrabajoUse Buen Juicio C272 Etiquetas de SeguridadDescripción del Producto Desmalezadora C272Especificaciones T272X/C272 Ensamblaje y Ajustes Mango T272/T272XDescripción Ajuste de la Holgura de la Palanca del Acelerador T272X/C272 Ensamblaje y Ajustes Protector del Accesorio de Corte T272X/C272Ensamblaje Instalación del Cabezal de Nylon T272 Instalación del Cabezal de Nylon T272X¡ADVERTENCIA 8. Retire la llave hexagonal Operación Mezcla de CombustibleArranque del motor Llenando el Tanque de CombustibleArranque del motor cont Cuando arranca el motor…Parada del motor Interruptor de Encendido Apagado Verifique La Condición De La Unidad ArnésCorte de Césped - Máquinas equipadas con cabezal de Nylon Usando un disco T272X/C272 Mantenimiento cada 10/15 Horas Mantenimiento GeneralMantenimiento Diario Mantenimiento Cada 10 HorasMantenimiento Cada 50 Horas Cada 135 Horas MantenimientoMantenimiento Afilado de Discos Almacenamiento de Largo PlazoPosible Causa GUIA DIAGNOSTICOEl Motor No Arranca Que RevisarQue Revisar GUIA DIAGNOSTICO continuaciónBAJA POTENCIA DiagnósticoSíntoma PROBLEMAS ADICIONALES3. Convertidor catalítico si está origi- nalmente equipado Declaración de Garantía del Sistema de Emisión1. Los componentes internos del car- burador 2. Los componentes del sistema de encendidoRevision 11/04 Shindaiwa Inc2004 Shindaiwa, Inc Part Number