Multiquip LT12DAB operation manual LIgHT TOWeR SaFeTY, Lamp SaFeTY

Page 5

Safety Information

LIgHT TOWeR SaFeTY

DangeR

„neveR use light tower in rain, snow, or

areas of high humidity that could generate electrical storms.

„neveR operate the equipment in an explosive atmosphere or near combustible materials.An explosion or fi re could result causing severe bodily harm or even death.

WaRnIng

„neveR disconnect any emergency or safety devices. These devices are intended for operator safety. Disconnection of these devices can cause severe injury, bodily harm or even death. Disconnection of any of these devices will void all warranties.

CauTIOn

„neveR lubricate components or attempt service on a running machine.

„aLWaYS ensure light tower is on level ground before use so that it cannot slide or shift around, endangering workers. Always keep immediate area free of bystanders.

„ALWAYS make sure trailer is leveled with all outriggers extended before raising tower. Outriggers must remain extended while tower is up.

„ALWAYS keep area behind trailer clear of people while raising and lowering mast.

„neveR remove safety pin or pull mast locking pin while tower is in a raised position!

„CHeCK the mast and winch cables for wear. If any problem occurs when lowering or raising the tower, STOP immediately! Contact a trained technician for assistance.

„neveR pivot or retract mast while unit is operating.

„neveR use the light tower mast as a crane. DO nOT lift anything with the mast.

„neveR attach anything to the light tower mast.

„aLWaYS lower the light tower when not in use, or if high winds or electrical storms are expected.

NOTICE

„aLWaYS keep the immediate area surrounding the light tower clean, neat, and free of debris.

„aLWaYS keep the machine in proper running condition.

„Fix damage to machine and replace any broken parts immediately.

„aLWaYS store equipment properly when it is not being used. Equipment should be stored in a clean, dry location out of the reach of children and unauthorized personnel.

„To prevent the light tower from overturning, neveR use in winds that exceed 65 mph (105 kph).

Lamp SaFeTY

WaRnIng

„neveR attempt to replace lamp with the power on. Always shut down the engine and turn off circuit breakers when changing the lamp.

„aLWaYS allow a sufficient amount of time for the lamp to cool before touching or changing. The possibility exists of severe burns.

CauTIOn

„neveR use force when installing the lamp.Excessive force could cause the lamp to break, causing bodily harm.

NOTICE

„neveR leave any grease or oil residue on lamp surface when replacing or removing lamp. This can create hot spots, reducing the service life of the lamp.

„aLWaYS make sure lamp surface is clean and dry.

„aLWaYS replace with MQ recommended type lamp.

„aLWaYS have a trained technician install and remove a fl oodlight, or replace any damaged fi xture wiring.

LT12Dab LIGHT TOWER • operation manual — rev. #0 (06/03/11) — page 5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Model LT12DAB Specifications are subject to change without notice Table of ContentsSaFeTY meSSageS Safety InformationSaFeTY SYmbOLS Addresses practices not related to personal injuryGeneRaL SaFeTY Lamp SaFeTY LIgHT TOWeR SaFeTY„ The engine of this equipment Requires an adequate free EngIne SaFeTYTOWIng SaFeTY FueL SaFeTY„ neveR use fuel as a cleaning agent From fuel vapors or if fuel is spilled on a hot engineLoading and Tie-Down on Flatbed Truck TRanSpORTIng SaFeTYPower Cord/Cable Safety ELeCTRICaL SaFeTYGrounding Safety „ aLWaYS make sure the areaEnvIROnmenTaL SaFeTY BaTTeRY SaFeTYLamp Footcandle Plot Lamp footcandle plotTrailer Specifications LT12DAB SpecificationsGenerator Specifications Engine Specifications Dimensions DimensionsReference Letter Description Dimension Length Mast Stowed Position Length Mast Deployed PositionConvenience Receptacle plates General informationMetal Halide Lamps Major Components Control Panel Side ComponentsView Control panel Controls and IndicatorsControl panel Inspection Indoor InstallationBefore starting Engine Oil CheckWipe up any spilled fuel immediately Battery CheckAir Cleaner Fan Belt Tension Cleaning the RadiatorCoolant Operation in Freezing WeatherLocation of Female Connectors Starting the Engine OperationMast operation Outriggers and Support StandsRaising the Mast Deploying the Mast to Vertical PositionLowering the Mast Stowing the Mast to Horizontal PositionMast Operation AUXILIARY Output Receptacles Turning On the LampsEmergency Shutdown Normal ShutdownBasic Inspection and Maintenance MaintenanceInspection/Maintenance FrequencyAir Cleaner Service DailyCleaning the Fuel Strainer General InspectionReplacing Fuel Filter Changing OilServicingthe Mast Raise/Lower Cable System Check Cable WearServicingthe Mast Extension Cable System Lower the mast to the horizontal resting positionRemoval From Long Term Storage StorageWheel Hub Adjustment Maintenance TrailersAdjustable Channel Leaf Suspension Components Leaf SuspensionSymptom Possible Problem Solution Generator TroubleshootingSymptom Possible Cause Solution Engine TroubleshootingEngine revolution is not Lamp Troubleshooting Replacement minimizes color differences When switch is first Checking voltage and ballast Turned onClean fixture Lamp starts slowly ARC does not strike Defective Lamp?Connections Lamp Troubleshooting GuideStarting Ballast RemovalStator Light tower wiring diagramWHT GRN BLK Lombardini engine wiring diagram COmmOn CauSeS for Loss of TRaILeR Trailer guidelinesTRaILeR TOWIng guIDeLIneS „ Driving too fast for the conditions obey local speed lawsCOupLIng to THe TOW veHICLe DRIvIng COnDITIOnSTRaILeR vIn Tag InOpeRabLe bRaKeS, LIgHTS or mIRRORSTRaILeR TOWIng TIpS TOW veHICLe ELeCTRICaL COnneCTORSuSpenSIOn SYSTem SIDe vIeW mIRRORSCOupLeR TYpeS SaFeTY CHaInSJaCKSTanD Coupling the Trailer to the Tow vehicle ball Coupler Lock washer and hitch frameUncoupling the ball Hitch Attaching Safety ChainConnecting Trailer Lights Pintle Coupler and pintle Hook PInTLe Hitch COupLeRCoupling Trailer to Tow vehicle pintle Coupler TIRe SaFeTY Unsafe Tires, Lug nuts or WheelsStep Determining Load Limit of TrailerTighten lug nuts before each tow Be sure lug nuts are tight before each towP indicates the tire is for passenger vehicles Determining Load Limit of Tow vehicle StepTIRe FunDamenTaLS Letter Rating Speed Rating Uniform Tire Quality grading Standards uTQgSTable a. Speed Rating Table b. Tire Wear Troubleshooting Tire Safety TipsTire Repair Replacing Worn or Damaged TiresWheel Rims Lights and SignalsWheels, bearings and Lug nuts Lug nut Torque RequirementsFigure L. Trailer to Tow Vehicle Wiring Diagram HERE’S HOW to GET Help

LT12DAB specifications

The Multiquip LT12DAB is an innovative and reliable light tower designed to deliver efficient lighting solutions for various outdoor applications. Known for its robust construction and user-friendly features, the LT12DAB is ideal for construction sites, events, and emergency situations, providing flexibility and performance in a compact package.

One of the standout features of the LT12DAB is its powerful lighting system. It is equipped with four high-intensity LED lights, each delivering up to 12,000 lumens, ensuring ample illumination for expansive areas. The LED technology not only enhances visibility but also offers advantages in power consumption, resulting in reduced energy costs and longer operational life. The tower can be raised up to 30 feet, enabling it to cast a broad beam of light across large outdoor spaces.

The LT12DAB is built with advanced mobility in mind. It features a durable, weather-resistant frame that can withstand various environmental conditions, making it suitable for use in diverse locations. The all-terrain wheels provide enhanced maneuverability, allowing operators to transport the unit easily across job sites or uneven terrains. Additionally, the lightweight design ensures that it can be easily handled by a small crew.

Powering the LT12DAB is a reliable and fuel-efficient diesel generator that provides extended run times without frequent refueling. This generator not only supports the lighting system but can also power additional tools and equipment, adding versatility to its functionality. The unit is designed with low noise emissions, making it ideal for operation in noise-sensitive areas.

Ease of use is paramount in the design of the LT12DAB. The intuitive control panel allows users to operate the lights and generator effortlessly. The telescopic mast can be raised or lowered quickly, with safety features in place to prevent accidental collapse. Moreover, the integrated sensors monitor the oil levels and engine temperature, providing alerts for maintenance needs.

In summary, the Multiquip LT12DAB combines powerful lighting capabilities with robust construction and user-friendly features. Its mobility, energy efficiency, and reliability make it a valuable tool for any outdoor project, ensuring that worksites remain well-lit and safe, regardless of the conditions. Whether for construction, events, or emergencies, the LT12DAB stands out for its performance and adaptability, meeting the demands of today’s professional environments.
Top Page Image Contents