Multiquip LT12DAB operation manual Location of Female Connectors

Page 23

inspection

CAUTION

NEVER start the engine with any circuit breakers in the ON position.

„„Light tower is placed on secure level ground with chock blocks underneath each wheel to prevent the light tower from rolling.

„„Outriggers have been fully extended to prevent the trailer from tipping.

„„Light tower trailer support stands have been positioned properly and the trailer is level.

„„Lamps have been adjusted to desired position.

„„Light tower trailer frame has been grounded correctly. „„Lamps do not interfere with any overhead obstructions.

DANGER

ALWAYS make sure the area above light tower is open and clear of overhead power lines and other obstructions. The tower extends in excess of 30 ft. (9 meters). Contact with overhead power lines or other obstructions could result in equipment damage, serious injury or death!

„„Lamp power cables have been plugged into the appropriate receptacles (J1-J4) on the T-Bar assembly. Follow instructions below to correctly install the power cable plugs.

a.Locate the 4 key-lock female 3-pin DIN connectors on the T-bar. See Figure 10.

KEY-LOCK

FEMALE

CONNECTORS

Figure 10. Location of Female Connectors

b.Locate the slot or key (A) on each female connector as shown in Figure 11.

Figure 11. Female Connector

c.On the corresponding male connector, locate the key tab (B) as shown in Figure 12.

B

Figure 12. Male Connector

d.Align the key tab (B) on the male connector with the slot or key (A) on the female connector and press together until fully seated.

e.Secure the connector by screwing the knurled locking nut of the male connector to the threaded portion of the female connector to ensure good contact between the two connectors. See Figure 13.

LOCKING

NUT

J1

J2

J3

 

 

 

 

 

J4

 

 

 

Figure 13. Cable Connectors

LT12Dab LIGHT TOWER • operation manual — rev. #0 (06/03/11) — page 23

Image 23
Contents Model LT12DAB Specifications are subject to change without notice Table of ContentsAddresses practices not related to personal injury Safety InformationSaFeTY meSSageS SaFeTY SYmbOLSGeneRaL SaFeTY Lamp SaFeTY LIgHT TOWeR SaFeTY„ The engine of this equipment Requires an adequate free EngIne SaFeTYFrom fuel vapors or if fuel is spilled on a hot engine FueL SaFeTYTOWIng SaFeTY „ neveR use fuel as a cleaning agentLoading and Tie-Down on Flatbed Truck TRanSpORTIng SaFeTY„ aLWaYS make sure the area ELeCTRICaL SaFeTYPower Cord/Cable Safety Grounding SafetyEnvIROnmenTaL SaFeTY BaTTeRY SaFeTYLamp Footcandle Plot Lamp footcandle plotTrailer Specifications LT12DAB SpecificationsGenerator Specifications Engine Specifications Length Mast Stowed Position Length Mast Deployed Position DimensionsDimensions Reference Letter Description DimensionConvenience Receptacle plates General informationMetal Halide Lamps Major Components Control Panel Side ComponentsView Control panel Controls and IndicatorsControl panel Engine Oil Check Indoor InstallationInspection Before startingWipe up any spilled fuel immediately Battery CheckOperation in Freezing Weather Cleaning the RadiatorAir Cleaner Fan Belt Tension CoolantLocation of Female Connectors Outriggers and Support Stands OperationStarting the Engine Mast operationStowing the Mast to Horizontal Position Deploying the Mast to Vertical PositionRaising the Mast Lowering the MastMast Operation AUXILIARY Output Receptacles Turning On the LampsEmergency Shutdown Normal ShutdownFrequency MaintenanceBasic Inspection and Maintenance Inspection/MaintenanceGeneral Inspection Service DailyAir Cleaner Cleaning the Fuel StrainerReplacing Fuel Filter Changing OilLower the mast to the horizontal resting position Check Cable WearServicingthe Mast Raise/Lower Cable System Servicingthe Mast Extension Cable SystemRemoval From Long Term Storage StorageWheel Hub Adjustment Maintenance TrailersAdjustable Channel Leaf Suspension Components Leaf SuspensionSymptom Possible Problem Solution Generator TroubleshootingSymptom Possible Cause Solution Engine TroubleshootingEngine revolution is not Lamp Troubleshooting Lamp starts slowly ARC does not strike Defective Lamp? When switch is first Checking voltage and ballast Turned onReplacement minimizes color differences Clean fixtureBallast Removal Lamp Troubleshooting GuideConnections StartingStator Light tower wiring diagramWHT GRN BLK Lombardini engine wiring diagram „ Driving too fast for the conditions obey local speed laws Trailer guidelinesCOmmOn CauSeS for Loss of TRaILeR TRaILeR TOWIng guIDeLIneSCOupLIng to THe TOW veHICLe DRIvIng COnDITIOnSTRaILeR vIn Tag InOpeRabLe bRaKeS, LIgHTS or mIRRORSTRaILeR TOWIng TIpS SIDe vIeW mIRRORS ELeCTRICaL COnneCTORTOW veHICLe SuSpenSIOn SYSTemCOupLeR TYpeS SaFeTY CHaInSJaCKSTanD Coupling the Trailer to the Tow vehicle ball Coupler Lock washer and hitch frameUncoupling the ball Hitch Attaching Safety ChainConnecting Trailer Lights Pintle Coupler and pintle Hook PInTLe Hitch COupLeRCoupling Trailer to Tow vehicle pintle Coupler TIRe SaFeTY Unsafe Tires, Lug nuts or WheelsBe sure lug nuts are tight before each tow Determining Load Limit of TrailerStep Tighten lug nuts before each towP indicates the tire is for passenger vehicles Determining Load Limit of Tow vehicle StepTIRe FunDamenTaLS Letter Rating Speed Rating Uniform Tire Quality grading Standards uTQgSTable a. Speed Rating Replacing Worn or Damaged Tires Tire Safety TipsTable b. Tire Wear Troubleshooting Tire RepairLug nut Torque Requirements Lights and SignalsWheel Rims Wheels, bearings and Lug nutsFigure L. Trailer to Tow Vehicle Wiring Diagram HERE’S HOW to GET Help

LT12DAB specifications

The Multiquip LT12DAB is an innovative and reliable light tower designed to deliver efficient lighting solutions for various outdoor applications. Known for its robust construction and user-friendly features, the LT12DAB is ideal for construction sites, events, and emergency situations, providing flexibility and performance in a compact package.

One of the standout features of the LT12DAB is its powerful lighting system. It is equipped with four high-intensity LED lights, each delivering up to 12,000 lumens, ensuring ample illumination for expansive areas. The LED technology not only enhances visibility but also offers advantages in power consumption, resulting in reduced energy costs and longer operational life. The tower can be raised up to 30 feet, enabling it to cast a broad beam of light across large outdoor spaces.

The LT12DAB is built with advanced mobility in mind. It features a durable, weather-resistant frame that can withstand various environmental conditions, making it suitable for use in diverse locations. The all-terrain wheels provide enhanced maneuverability, allowing operators to transport the unit easily across job sites or uneven terrains. Additionally, the lightweight design ensures that it can be easily handled by a small crew.

Powering the LT12DAB is a reliable and fuel-efficient diesel generator that provides extended run times without frequent refueling. This generator not only supports the lighting system but can also power additional tools and equipment, adding versatility to its functionality. The unit is designed with low noise emissions, making it ideal for operation in noise-sensitive areas.

Ease of use is paramount in the design of the LT12DAB. The intuitive control panel allows users to operate the lights and generator effortlessly. The telescopic mast can be raised or lowered quickly, with safety features in place to prevent accidental collapse. Moreover, the integrated sensors monitor the oil levels and engine temperature, providing alerts for maintenance needs.

In summary, the Multiquip LT12DAB combines powerful lighting capabilities with robust construction and user-friendly features. Its mobility, energy efficiency, and reliability make it a valuable tool for any outdoor project, ensuring that worksites remain well-lit and safe, regardless of the conditions. Whether for construction, events, or emergencies, the LT12DAB stands out for its performance and adaptability, meeting the demands of today’s professional environments.