Multiquip LT12DAB Attaching Safety Chain, Connecting Trailer Lights, Uncoupling the ball Hitch

Page 51

trailer guidelines

attaching Safety Chain

Visually inspect the safety chains and hooks for wear or damage. Replace worn or damaged safety chains and hooks before towing.

Attach the safety chains so that they:

• Cross underneath the coupler. See Figure E.

TOW

VEHICLE

TRAILER

TONGUE

SAFETY CHAIN

 

MASTER LINK

IMPORTANT!

 

CROSS BOTH

SAFETY CHAINS

Figure E. Attaching Safety Chain (Ball Hitch)

•Loop around a frame member of the tow vehicle or holes provided in the hitch system (DO NOT attach them to an interchangeable part of the hitch assembly).

•Have enough slack to permit tight turns, but not be close to the road surface, so if the trailer uncouples, the safety chains can hold the tongue up above the road

. WaRnIng

Improper rigging of the safety chains can result in loss of control of the trailer and tow vehicle, leading to death or serious injury, if the trailer uncouples from the tow vehicle.

•Fasten chains to frame of tow vehicle. DO NOT fasten chains to any part of the hitch unless the hitch has holes or loops specifi cally for that purpose.

•Cross chains underneath hitch and coupler with enough slack to permit turning and to hold tongue up, if the trailer comes loose.

Connecting Trailer Lights

Connect the trailer lights to the tow vehicle’s electrical system using the electric connectors at the front of the trailer (tongue). Refer to the wiring diagram shown in the trailer wiring diagram section of this manual. Before towing the trailer check for the following:

„Running lights (turn on tow vehicle headlights).

„Brake Lights (step on tow vehicle brake pedal).

„Backup Lights (place tow vehicle gear shift in reverse).

„Turn Signals (activate tow vehicle directional signal lever).

WaRnIng

Improper electrical connection between the tow vehicle and the trailer will result in inoperable lights and electric brakes, and can lead to collision.

Before each tow:

•Check that the taillights, brake lights and turn signals work.

•Check that the electric brakes work by operating the brake controller inside the tow vehicle.

uncoupling the ball Hitch

Follow these steps to uncouple ball hitch from tow vehicle:

„Block trailer tires to prevent the trailer from rolling, before jacking the trailer up.

„Disconnect the electrical connector.

„Disconnect the breakaway brake switch cable. Promptly replace the pullpin in the switchbox.

„Before extending jackstand, make certain the ground surface below the jackstand foot will support the tongue load.

„Rotate the jackstand handle (or crank) clockwise. This will slowly extend the jack and transfer the weight of the trailer tongue to the jack.

LT12Dab LIGHT TOWER • operation manual — rev. #0 (06/03/11) — page 51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Model LT12DAB Specifications are subject to change without notice Table of ContentsAddresses practices not related to personal injury Safety InformationSaFeTY meSSageS SaFeTY SYmbOLSGeneRaL SaFeTY Lamp SaFeTY LIgHT TOWeR SaFeTY„ The engine of this equipment Requires an adequate free EngIne SaFeTYFrom fuel vapors or if fuel is spilled on a hot engine FueL SaFeTYTOWIng SaFeTY „ neveR use fuel as a cleaning agentLoading and Tie-Down on Flatbed Truck TRanSpORTIng SaFeTY„ aLWaYS make sure the area ELeCTRICaL SaFeTYPower Cord/Cable Safety Grounding SafetyEnvIROnmenTaL SaFeTY BaTTeRY SaFeTYLamp Footcandle Plot Lamp footcandle plotLT12DAB Specifications Generator SpecificationsTrailer Specifications Engine Specifications Length Mast Stowed Position Length Mast Deployed Position DimensionsDimensions Reference Letter Description DimensionGeneral information Metal Halide LampsConvenience Receptacle plates Major Components Control Panel Side ComponentsView Control panel Controls and IndicatorsControl panel Engine Oil Check Indoor InstallationInspection Before startingWipe up any spilled fuel immediately Battery CheckOperation in Freezing Weather Cleaning the RadiatorAir Cleaner Fan Belt Tension CoolantLocation of Female Connectors Outriggers and Support Stands OperationStarting the Engine Mast operationStowing the Mast to Horizontal Position Deploying the Mast to Vertical PositionRaising the Mast Lowering the MastMast Operation AUXILIARY Output Receptacles Turning On the LampsEmergency Shutdown Normal ShutdownFrequency MaintenanceBasic Inspection and Maintenance Inspection/MaintenanceGeneral Inspection Service DailyAir Cleaner Cleaning the Fuel StrainerReplacing Fuel Filter Changing OilLower the mast to the horizontal resting position Check Cable WearServicingthe Mast Raise/Lower Cable System Servicingthe Mast Extension Cable SystemRemoval From Long Term Storage StorageMaintenance Trailers Adjustable ChannelWheel Hub Adjustment Leaf Suspension Components Leaf SuspensionSymptom Possible Problem Solution Generator TroubleshootingSymptom Possible Cause Solution Engine TroubleshootingEngine revolution is not Lamp Troubleshooting Lamp starts slowly ARC does not strike Defective Lamp? When switch is first Checking voltage and ballast Turned onReplacement minimizes color differences Clean fixtureBallast Removal Lamp Troubleshooting GuideConnections StartingStator Light tower wiring diagramWHT GRN BLK Lombardini engine wiring diagram „ Driving too fast for the conditions obey local speed laws Trailer guidelinesCOmmOn CauSeS for Loss of TRaILeR TRaILeR TOWIng guIDeLIneSCOupLIng to THe TOW veHICLe DRIvIng COnDITIOnSInOpeRabLe bRaKeS, LIgHTS or mIRRORS TRaILeR TOWIng TIpSTRaILeR vIn Tag SIDe vIeW mIRRORS ELeCTRICaL COnneCTORTOW veHICLe SuSpenSIOn SYSTemSaFeTY CHaInS JaCKSTanDCOupLeR TYpeS Coupling the Trailer to the Tow vehicle ball Coupler Lock washer and hitch frameAttaching Safety Chain Connecting Trailer LightsUncoupling the ball Hitch Pintle Coupler and pintle Hook PInTLe Hitch COupLeRCoupling Trailer to Tow vehicle pintle Coupler TIRe SaFeTY Unsafe Tires, Lug nuts or WheelsBe sure lug nuts are tight before each tow Determining Load Limit of TrailerStep Tighten lug nuts before each towDetermining Load Limit of Tow vehicle Step TIRe FunDamenTaLSP indicates the tire is for passenger vehicles Uniform Tire Quality grading Standards uTQgS Table a. Speed RatingLetter Rating Speed Rating Replacing Worn or Damaged Tires Tire Safety TipsTable b. Tire Wear Troubleshooting Tire RepairLug nut Torque Requirements Lights and SignalsWheel Rims Wheels, bearings and Lug nutsFigure L. Trailer to Tow Vehicle Wiring Diagram HERE’S HOW to GET Help

LT12DAB specifications

The Multiquip LT12DAB is an innovative and reliable light tower designed to deliver efficient lighting solutions for various outdoor applications. Known for its robust construction and user-friendly features, the LT12DAB is ideal for construction sites, events, and emergency situations, providing flexibility and performance in a compact package.

One of the standout features of the LT12DAB is its powerful lighting system. It is equipped with four high-intensity LED lights, each delivering up to 12,000 lumens, ensuring ample illumination for expansive areas. The LED technology not only enhances visibility but also offers advantages in power consumption, resulting in reduced energy costs and longer operational life. The tower can be raised up to 30 feet, enabling it to cast a broad beam of light across large outdoor spaces.

The LT12DAB is built with advanced mobility in mind. It features a durable, weather-resistant frame that can withstand various environmental conditions, making it suitable for use in diverse locations. The all-terrain wheels provide enhanced maneuverability, allowing operators to transport the unit easily across job sites or uneven terrains. Additionally, the lightweight design ensures that it can be easily handled by a small crew.

Powering the LT12DAB is a reliable and fuel-efficient diesel generator that provides extended run times without frequent refueling. This generator not only supports the lighting system but can also power additional tools and equipment, adding versatility to its functionality. The unit is designed with low noise emissions, making it ideal for operation in noise-sensitive areas.

Ease of use is paramount in the design of the LT12DAB. The intuitive control panel allows users to operate the lights and generator effortlessly. The telescopic mast can be raised or lowered quickly, with safety features in place to prevent accidental collapse. Moreover, the integrated sensors monitor the oil levels and engine temperature, providing alerts for maintenance needs.

In summary, the Multiquip LT12DAB combines powerful lighting capabilities with robust construction and user-friendly features. Its mobility, energy efficiency, and reliability make it a valuable tool for any outdoor project, ensuring that worksites remain well-lit and safe, regardless of the conditions. Whether for construction, events, or emergencies, the LT12DAB stands out for its performance and adaptability, meeting the demands of today’s professional environments.
Top Page Image Contents