Multiquip MQP20P manual EleCTRiCal SaFeTY, Grounding Safety, Power Cord/Cable Safety

Page 10

Safety Information

eleCTRiCal SaFeTY

DaNgeR

„DO NOT touch output terminals during operation. Contact with output terminals during operation can cause electrocution, electrical shock or burn.

„The electrical voltage required to operate the generator can cause severe

injury or even death through physical contact with live circuits. Turn generator and all circuit breakers OFF before performing maintenance on the generator or making contact with output terminals.

„ NeveR insert any objects into the output receptacles during operation. This is extremely dangerous.The possibility exists of electrical shock, electrocution or

death.

„Backfeed to a utility system can cause

electrocution and/or property damage. NeveR connect the generator to a building’s electrical system without a transfer switch or other approved

device. All installations should be

performed by a licensed electrician in accordance with all applicable laws and electrical codes. Failure to do so could result in electrical shock or burn, causing serious injury or even death.

„Make sure power cables are securely connected to the generator’s output receptacles. Incorrect connections may cause electrical shock and damage to the generator.

NOTICE

„alWaYS make certain that proper power or extension cord has been selected for the job. See Cable Selection Chart in this manual.

grounding Safety

DaNgeR

„alWaYS make sure that electrical circuits are properly grounded to a suitable earth ground (ground rod) per the National Electrical Code (NEC) and local codes before operating generator. Severe injury or death by electrocution can result from operating an ungrounded generator.

„NeveR use gas piping as an electrical ground.

power Cord/Cable Safety

DaNgeR

„NeveR let power cords or cables lay in water.

„NeveR stand in water while AC power from the generator is being transferred to a load.

„NeveR use damaged or worn cables or cords when connecting equipment to generator. Inspect for cuts in the insulation.

„ NeveR grab or touch a live power cord or cable with wet hands. The possibility exists of electrical shock, electrocution or death.

page 10 —MQP20P STANDBY GENERATOR • operation and parts manual — rev. #1 (11/28/11)

Image 10
Contents Model MQP20P Proposition 65 warning Diesel engine exhaust and somePage Table of Contents MQP20P Standby GeneratorChoose from three easy options Safety Information SaFeTY MeSSageSGeNeRal SaFeTY GeNeRaTOR SaFeTYENgiNe SaFeTY Restricted. If the air fl ow isFuel SaFeTY TOWiNg SaFeTYGrounding Safety EleCTRiCal SaFeTYPower Cord/Cable Safety BaTTeRY SaFeTY ENviRONMeNTal SaFeTYSpecifications Dimensions Installation Typical Generator Grounding ApplicationMounting Outdoor InstallationIndoor Installation Generator GroundingGenerator General informationCamlok outlet box panel Engine Principle of operationElectrONIC Governor System Major components Item no DescriptionBasic engine components Basic Engine ComponentsDigital controller panel Microprocessor Engine Controller MECConnector outlet box and main circuit breaker Outlet connectorsLoad application/generator output Single Phase LoadGenerator Amperage Lubrication Oil Inspection/setupRefueling Procedure Fuel CheckFuel Expands Battery Cleaning the RadiatorAir Cleaner Fan Belt Tension Coolant Antifreeze/summer coolantAlternator Battery Cable InstallationWiring Piping and Hose ConnectionBefore Starting Starting Auto ModeStartup Starting ManualNormal Shutdown Procedure Emergency Shutdown ProcedureJacketWater Heater and Internal Battery Charger Battery Charger and Jacket Water Heater Power ConnectionsProtective devices Protective devicesTransporting TransportingAir Filter Dust Indicator MaintenanceGeneral Inspection Air Filter Removing Water from the Fuel Tank Cleaning Inside the Fuel TankFuel Addition Fuel Tank InspectionFlushing Out Radiator and Replacing Coolant Radiator CleaningVoltage regulator adjustments PotentiometersAdjustment Procedure Generator StorageTroubleshooting Generator Troubleshooting GeneratorTroubleshooting engine Troubleshooting EngineTroubleshooting controller Troubleshooting MEC20 ControllerImproper calibration? Troubleshooting Voltage Regulator Troubleshooting Voltage RegulatorMaintenance Parts Locator Generator Wiring Diagram single phase Control BOXCircuit Breaker BOX Generator Wiring Diagram three phase 505 K1 Explanation of Code in Remarks Column Suggested Spare Parts MQP20P with Perkins 404D-22 Diesel Engine 1 to 3 unitsHousing assy Part Name Engine and Generator Mounting assy GENERATOR, 30KW Fuel assy Part Name QTY Remarks Electrical assy BOLT, BATTERY, 10.38 Jacket Water HEater assy BRACKET, MOUNTING, Heater Solenoid assy BRACKET, Starter Solenoid Radiator assy Guard Air filter assy Cover Engine exhaust assy Exhaust Flex Engine Oil assy OIL Filler CAP Control panel assy PANEL, FRONT, Control Panel Controller assy MODULE, Output Expan MEC 2/20 W/CABLE Saddlebox assy Phase Units Circuit breaker assy Ground Housing Camlok assyCOVER, HINGED, Black Terms and Conditions of Sale Parts FReigHT pOliCYPage HERE’S HOW to GET Help