Multiquip M4870300104B DCA-220SSJ/SSJU Setup, Circuit Breakers, Lubrication Oil, Fuel Check

Page 48

Circuit Breakers

To protect the generator from an overload, a 3-pole, 600 amp, main circuit breaker is provided to protect the U,V, and W OutputTerminals from overload. In addition two single-pole, 20 amp GFCI circuit breakers are provided to protect the GFCI receptacles from overload. Three 50 amp load circuit breakers have also been provided to protect the auxiliary receptacles from overload. Make sure to switch ALL circuit breakers to the OFF position prior to starting the engine.

Lubrication Oil

Fill the engine crankcase with lubricating oil through the filler hole, but DO NOT overfill. Make sure the generator is level. and verify that the oil level is maintained between the two notches (Figure 30) on the dipstick. See Table 9 for proper selection of engine oil.

DCA-220SSJ/SSJU — SETUP

Fuel Check

DANGER - EXPLOSION/FIRE HAZARDS

Fuel spillage on a hot engine can cause a fire or explosion. If fuel spillage occurs, wipe up the spilled fuel completely to prevent fire hazards. NEVER smoke around or near the generator.

Refilling the Fuel System

CAUTION - REFUELINGTHE GENERATOR

ONLY properly trained personel who have read and understand this section should refill the fuel tank system.

Figure 30. Engine Oil Dipstick

When checking the engine oil, be sure to check if the oil is clean. If the oil is not clean, drain the oil by removing the oil drain plug, and refill with the specified amount of oil as outlined in the John Deere Engine Owner's Manual. Oil should be warm before draining.

Other types of motor oils may be substituted if they meet the following requirements:

API Service Classification CC/SC

API Service Classification CC/SD

API Service Classification CC/SE

API Service Classification CC/SF

This generator has an internal fuel tank located inside the trailer frame and may also be equipped with an environmental fuel tank (Figure 31). ALWAYS fill the fuel tanks with clean fresh #2 diesel fuel. DO NOT fill the fuel tanks beyond their capacities.

Pay attention to the fuel tank capacity when replenishing fuel.The fuel tank cap must be closed tightly after filling. Handle fuel in a safety container. If the container does not have a spout, use a funnel. Wipe up any spilled fuel immediately.

Figure 31. Internal Fuel Tank System

PAGE 48 — DCA-220SSJ/SSJU — OPERATION AND PARTS MANUAL — REV. #1 (02/28/14)

Image 48
Contents Model DCA220SSJ/SSJU DCA-220SSJ/SSJU Proposition 65WARNING DCA-220SSJ/SSJU Note DCA-220SSJ/SSJU -TABLE of Contents DCA-220SSJ/SSJU Parts Ordering Procedures Ordering parts has never been easierDCA-220SSJ/SSJU Specifications DCA-220SSJ/SSJU Dimensions TOP, Side and Front DimensionsDCA-220SSJ/SSJU Safety Message Alert Symbols Hazard SymbolsDCA-220SSJ/SSJU Safety Message Alert Symbols General Safety DCA-220SSJ/SSJU Rules for Safe OperationDrugs or alcohol BurnsElectrical Safety DCA-220SSJ/SSJU Rules for Safe OperationGenerator Grounding Maintenance Safety Battery SafetyTowing &Transporting Safety EmergenciesDCA-220SSJ/SSJU Generator Decals Generator DecalsDCA-220SSJ/SSJU Generator Decals Generator Decals Cont inuedDCA-220SSJ/SSJU Installation Typical Generator Grounding ApplicationDCA-220SSJ/SSJU Installation Outdoor InstallationIndoor Installation MountingDCA-220SSJ/SSJU General Information DCA-220SSJ/SSJU Major Components Major ComponentsDCA-220SSJ/SSJU Diagnostic Display Menu Button Press this button to enter or exit menu screensDisplay Parameters DCA-220SSJ/SSJU Diagnostic Display First Time Start UpNext item down Main Menu NavigationDiagnostic Code Stored Fault CodesEngine Configuration Data To make a selectionDCA-220SSJ/SSJU Diagnostic Display DCA-220SSJ/SSJU Diagnostic Display Auxiliary Gage Fault Display will return to the single or four parameter screenActive Fault Codes Backlight Adjustment Shut Down CodesCode from an engine control unit the single or four DamageContrast Adjustment IntensityIs highlighted Setup 1- Up Display Select UnitsOnce the Setup 1-up Display menu icon has been Setup menuUp display function Automatic Scan on Setup 4-Up Display Select the 4-Up Custom Setup from the 4-Up Setup menuEngine OIL Temperature HighlightedWhen the gage data has cleared, the display Gage Data is selected the PowerView willVersion currently in the diagnostic display Half duplexTouch the Menu button again to return to the Main MenuTouch the Menu Button Highlight it, then touch Enter DCA-220SSJ/SSJU Diagnostic Display Glossary Troubleshooting informationECU did not respond to the PowerView request No parameter selected for this 4- UP quadrantDCA-220SSJ/SSJU Generator Control Panel DCA-220SSJ/SSJU Engine Operating Panel Fuel Gauge Indicates amount of diesel fuel availableDCA-220SSJ/SSJU Engine Operating Panel Auto On/Off Engine Controller MpecDCA-220SSJ/SSJU Output Terminal Panel Familiarization Output Terminal FamiliarizationDCA-220SSJ/SSJU Output Terminal Panel Familiarization 100VAC Gfci ReceptaclesConnecting Loads Over Current RelaySingle Phase Load Three Phase LoadDCA-220SSJ/SSJU Load Application DCA-220SSJ/SSJU Generator Outputs How to Read the Output Terminal Gauge DCA-220SSJ/SSJU Generator OUTPUTS/ Gauge ReadingMaximum Amps DCA-220SSJ/SSJU Output Terminal Panel Connections Uvwo Terminal Output Voltages3Ø-240V Uvwo Terminal Output Voltages 1Ø-240V Uvwo Terminal Output VoltagesDCA-220SSJ/SSJU Output Terminal Panel Connections 3Ø-480V Uvwo Terminal Output Voltages1Ø-480V Uvwo Terminal Output Voltages 1Ø-277V Uvwo Terminal Output VoltagesDCA-220SSJ/SSJU Setup Circuit BreakersLubrication Oil Fuel CheckDCA-220SSJ/SSJU Setup Refueling ProcedureONLY! use #2 diesel fuel when refueling Cleaning the Radiator Air Cleaner Fan Belt TensionCoolant Antifreeze Operation FreezingWeatherBattery Battery Cable InstallationWiring AlternatorDCA-220SSJ/SSJU Generator START-UP Procedure Manual Place the engine speed switch in the LOW down positionBefore Starting Engines exhaust contains harmful emissionsEngine Speed Switch High Starting Auto Mode No LoadTachometer Gauge Place the engine speed switch in the High position Place the Mpec Control Switch in the Auto positionNormal Shutdown Procedure Emergency Shutdown ProcedureDCA-220SSJ/SSJU Maintenance Engine DCA-220SSJ/SSJU Maintenance Engine DCA-220SSJ/SSJU Maintenance HEATER/CHARGER DCA-220SSJ/SSJU Maintenance Trailer Trailer MaintenanceBrake Adjustment BrakesCheck the wheel and drum for free rotation Hydraulic Surge BrakesTires/Wheels/Lug Nuts TireWear/InflationSuspension DCA-220SSJ/SSJU Maintenance Trailer Lug Nut Torque RequirementsStart all wheel lug nuts by hand Never use an pneumatic air gun to tighten wheel lug nutsDCA-220SSJ/SSJU -TRAILERWIRING Diagram Trailer/Towing Vehicle Wiring DiagramDCA-220SSJ/SSJU Generatorwiring Diagram Generator Wiring DiagramDCA-220SSJ/SSJU Enginewiring Diagram Engine Wiring DiagramDCA-220SSJ/SSJU -TROUBLESHOOTING Generator Generator TroubleshootingDCA-220SSJ/SSJU -TROUBLESHOOTING Engine Controller Engine Controller Troubleshooting MpecDCA-220SSJ/SSJU Operation and Parts Manual REV. #1 02/28/14 DCA220SSJ/SSJU Explanation of Code in Remarks Column QTY. ColumnDCA220SSJ/SSJU Suggested Spare Parts DescriptionDCA220SSJ/SSJU Generator Assy DCA220SSJ/SSJU Generator Assy DCA220SSJ/SSJU- Generator ASSY. DCA220SSJ/SSJU Generator ASSY. DCA220SSJ/SSJU Control Panel Assy DCA220SSJ/SSJU- Control Panel Assy DCA220SSJ/SSJU Control BOX Assy DCA220SSJ/SSJU Control BOX Assy DCA220SSJ/SSJU Control BOX ASSY. DCA220SSJ/SSJU Control BOX ASSY. DCA220SSJ/SSJU- Engine and Radiator Assy DCA220SSJ/SSJU Engine and Radiator Assy DCA220SSJ/SSJU Engine and Radiator Assy M4310301203 32A M4493601204M4310300903 M4310301003DCA220SSJ/SSJU Engine and Radiator Assy 0602021070 02692006600802081003 M9300000203DCA220SSJ/SSJU Outputterminal Assy DCA220SSJ/SSJU Outputterminal Assy DCA220SSJ/SSJU Outputterminal ASSY. DCA220SSJ/SSJU Outputterminal ASSY. DCA220SSJ/SSJU Battery Assy DCA220SSJ/SSJU Battery Assy DCA220SSJ/SSJU Muffler Assy DCA220SSJ/SSJU Muffler Assy DCA220SSJ/SSJU Fueltank Assy DCA220SSJ/SSJU Fueltank Assy DCA220SSJ/SSJU Enclosure Assy DCA220SSJ/SSJU Enclosure Assy DCA220SSJ/SSJU Enclosure ASSY. DCA220SSJ/SSJU Enclosure ASSY. DCA220SSJ/SSJU Enclosure ASSY. DCA220SSJ/SSJU Enclosure ASSY. DCA220SSJ/SSJU Enclosure ASSY. M9113000102 62A 0030006000M4453600004 M4453600104DCA220SSJ/SSJU Rubber Seals Assy DCA220SSJ/SSJU Rubber Seals Assy DCA220SSJ/SSJU Nameplate and Decals Assy DCA220SSJ/SSJU Nameplate and Decals Assy DCA220SSJ/SSJU Nameplate and Decals ASSY. DCA220SSJ/SSJU Nameplate and Decals ASSY. Terms and Conditions of Sale Parts Freight PolicyDCA-220SSJ/SSJU Operation and Parts Manual REV. #1 02/28/14 HERE’S HOW to GET Help

C1870300404, M4870300104B specifications

Multiquip, a leading manufacturer in the construction and industrial sectors, offers a wide range of durable and reliable products. Among its extensive portfolio, two notable models stand out: the M4870300104B and the C1870300404. These models are particularly praised for their efficiency, innovative technologies, and robust features that cater to various construction needs.

The Multiquip M4870300104B is a powerful multi-process welder, designed to tackle a wide variety of welding applications. This model is equipped with an advanced inverter technology that allows it to deliver smooth and stable arcs for TIG, MIG, and Stick welding. The inverter design also enhances energy efficiency, making it an ideal choice for both on-site and workshop use. Furthermore, the M4870300104B features a dual-voltage capability, supporting both 120V and 240V input, which provides flexibility for different job sites.

In terms of usability, the M4870300104B boasts an intuitive control panel that allows for easy adjustments. Its lightweight design ensures easy transport, while the rugged construction promises durability in demanding environments. With a duty cycle of 35% at 200 Amps, this welder is built for efficiency and long-lasting performance, making it suitable for both professional and DIY applications.

On the other hand, the C1870300404 is a high-performance concrete vibratory screed that plays a crucial role in ensuring smooth finishes on concrete surfaces. This model is engineered with advanced vibration technology which allows it to efficiently remove air pockets and stabilize the concrete. The C1870300404 features a robust aluminum frame, enhancing its durability while maintaining a lightweight structure for ease of handling.

Equipped with a powerful and reliable engine, the C1870300404 offers impressive runtime, allowing crews to work continuously without frequent interruptions. It also features adjustable vibration settings, enabling users to customize the intensity based on the specific requirements of the project at hand. The ergonomic design of the handle contributes to user comfort, reducing fatigue during extended periods of operation.

In conclusion, both the Multiquip M4870300104B and C1870300404 exemplify the brand’s commitment to quality, innovation, and user-centric design. These tools not only enhance productivity but also guarantee precision and efficiency in various construction tasks. Whether for welding or concrete finishing, Multiquip continues to deliver equipment that meets the evolving demands of the industry.