Multiquip M4870300104B, C1870300404 operation manual No Load, Tachometer Gauge, Starting Auto Mode

Page 54
Figure 54. Ammeter
(Load)

DCA-220SSJ/SSJU — GENERATOR START-UP PROCEDURE (MANUAL)

18. Place the main, GFCI, and aux. circuit breakers in the ON position (Figure 53).

Figure 48. Voltage Adjust Control Knob

14.The ammeter (Figure 49) will indicate zero amps with no load applied.When a load is applied, the ammeter will indicate the amount of current that the load is drawing from the generator.

Figure 49. Ammeter

(No Load)

15.The engine oil pressure gauge (Figure 50) will indicate the oil pressure of the engine. Under normal operating conditions the oil pressure is approximately 35 to 65 psi. (241~448 kPa). When starting the generator

Figure 50. Oil

Pressure Gauge

16.The coolant temperature gauge (Figure 51) will indicate the coolant temperature. Under normal operating conditions the coolant temperature should be between 180~230°F (82~110 °C) Green Zone.

Figure 51. Coolant

Temperature Gauge

17.Thetachometergauge(Figure52) will indicate the speed of the engine when the generator is operating. Under normal operating conditions this speed is approximately 1800 RPM’s.

Figure 52. Engine

Tachometer Gauge

Figure 53. Main, Aux. and GFCI

Circuit Breakers (ON)

19. Observe the generator's ammeter (Figure 54) and verify it reads the anticipated amount of current with respect to the load. The ammeter will only display a current reading if a load is in use.

20.The generator will run until manually stopped or an abnormal condition occurs.

Starting (Auto Mode)

DANGER - ELECTRICAL SYSTEM HAZARDS

Before connecting this generator to any building’s electrical system, a licensed electrician must install an isolation (transfer) switch. Serious damage to the building’s electrical system may occur without this transfer switch.

CAUTION - BACKUP GENERATOR USE

When connecting the generator to a isolation (transfer) switch, ALWAYS have power applied to the generator's internal battery charger. This will ensure that the engine will not fail due to a dead battery.

NOTICE

When the generator is set in the AUTO mode, the generator will automically start in the event of comercial power falling below a prescribed level by means of a contact closure that is generated automatically by a transfer switch.

PAGE 54 — DCA-220SSJ/SSJU — OPERATION AND PARTS MANUAL — REV. #1 (02/28/14)

Image 54
Contents Model DCA220SSJ/SSJU DCA-220SSJ/SSJU Proposition 65WARNING DCA-220SSJ/SSJU Note DCA-220SSJ/SSJU -TABLE of Contents DCA-220SSJ/SSJU Parts Ordering Procedures Ordering parts has never been easierDCA-220SSJ/SSJU Specifications DCA-220SSJ/SSJU Dimensions TOP, Side and Front DimensionsDCA-220SSJ/SSJU Safety Message Alert Symbols Hazard SymbolsDCA-220SSJ/SSJU Safety Message Alert Symbols Drugs or alcohol General SafetyDCA-220SSJ/SSJU Rules for Safe Operation BurnsElectrical Safety DCA-220SSJ/SSJU Rules for Safe OperationGenerator Grounding Maintenance Safety Battery SafetyTowing &Transporting Safety EmergenciesDCA-220SSJ/SSJU Generator Decals Generator DecalsDCA-220SSJ/SSJU Generator Decals Generator Decals Cont inuedDCA-220SSJ/SSJU Installation Typical Generator Grounding ApplicationIndoor Installation DCA-220SSJ/SSJU InstallationOutdoor Installation MountingDCA-220SSJ/SSJU General Information DCA-220SSJ/SSJU Major Components Major ComponentsDCA-220SSJ/SSJU Diagnostic Display Menu Button Press this button to enter or exit menu screensDisplay Parameters Next item down DCA-220SSJ/SSJU Diagnostic DisplayFirst Time Start Up Main Menu NavigationEngine Configuration Data Diagnostic CodeStored Fault Codes To make a selectionDCA-220SSJ/SSJU Diagnostic Display DCA-220SSJ/SSJU Diagnostic Display Auxiliary Gage Fault Display will return to the single or four parameter screenActive Fault Codes Code from an engine control unit the single or four Backlight AdjustmentShut Down Codes DamageContrast Adjustment IntensityIs highlighted Setup 1- Up Display Select UnitsOnce the Setup 1-up Display menu icon has been Setup menuUp display function Automatic Scan on Setup 4-Up Display Select the 4-Up Custom Setup from the 4-Up Setup menuEngine OIL Temperature HighlightedVersion currently in the diagnostic display When the gage data has cleared, the displayGage Data is selected the PowerView will Half duplexTouch the Menu button again to return to the Main MenuTouch the Menu Button Highlight it, then touch Enter ECU did not respond to the PowerView request DCA-220SSJ/SSJU Diagnostic DisplayGlossary Troubleshooting information No parameter selected for this 4- UP quadrantDCA-220SSJ/SSJU Generator Control Panel DCA-220SSJ/SSJU Engine Operating Panel Fuel Gauge Indicates amount of diesel fuel availableDCA-220SSJ/SSJU Engine Operating Panel Auto On/Off Engine Controller MpecDCA-220SSJ/SSJU Output Terminal Panel Familiarization Output Terminal FamiliarizationDCA-220SSJ/SSJU Output Terminal Panel Familiarization 100VAC Gfci ReceptaclesConnecting Loads Over Current RelaySingle Phase Load Three Phase LoadDCA-220SSJ/SSJU Load Application DCA-220SSJ/SSJU Generator Outputs How to Read the Output Terminal Gauge DCA-220SSJ/SSJU Generator OUTPUTS/ Gauge ReadingMaximum Amps 3Ø-240V Uvwo Terminal Output Voltages DCA-220SSJ/SSJU Output Terminal Panel ConnectionsUvwo Terminal Output Voltages 1Ø-240V Uvwo Terminal Output Voltages1Ø-480V Uvwo Terminal Output Voltages DCA-220SSJ/SSJU Output Terminal Panel Connections3Ø-480V Uvwo Terminal Output Voltages 1Ø-277V Uvwo Terminal Output VoltagesLubrication Oil DCA-220SSJ/SSJU SetupCircuit Breakers Fuel CheckDCA-220SSJ/SSJU Setup Refueling ProcedureONLY! use #2 diesel fuel when refueling Coolant Antifreeze Cleaning the RadiatorAir Cleaner Fan Belt Tension Operation FreezingWeatherWiring BatteryBattery Cable Installation AlternatorBefore Starting DCA-220SSJ/SSJU Generator START-UP Procedure ManualPlace the engine speed switch in the LOW down position Engines exhaust contains harmful emissionsEngine Speed Switch High Starting Auto Mode No LoadTachometer Gauge Place the engine speed switch in the High position Place the Mpec Control Switch in the Auto positionNormal Shutdown Procedure Emergency Shutdown ProcedureDCA-220SSJ/SSJU Maintenance Engine DCA-220SSJ/SSJU Maintenance Engine DCA-220SSJ/SSJU Maintenance HEATER/CHARGER DCA-220SSJ/SSJU Maintenance Trailer Trailer MaintenanceCheck the wheel and drum for free rotation Brake AdjustmentBrakes Hydraulic Surge BrakesTires/Wheels/Lug Nuts TireWear/InflationSuspension Start all wheel lug nuts by hand DCA-220SSJ/SSJU Maintenance TrailerLug Nut Torque Requirements Never use an pneumatic air gun to tighten wheel lug nutsDCA-220SSJ/SSJU -TRAILERWIRING Diagram Trailer/Towing Vehicle Wiring DiagramDCA-220SSJ/SSJU Generatorwiring Diagram Generator Wiring DiagramDCA-220SSJ/SSJU Enginewiring Diagram Engine Wiring DiagramDCA-220SSJ/SSJU -TROUBLESHOOTING Generator Generator TroubleshootingDCA-220SSJ/SSJU -TROUBLESHOOTING Engine Controller Engine Controller Troubleshooting MpecDCA-220SSJ/SSJU Operation and Parts Manual REV. #1 02/28/14 DCA220SSJ/SSJU Explanation of Code in Remarks Column QTY. ColumnDCA220SSJ/SSJU Suggested Spare Parts DescriptionDCA220SSJ/SSJU Generator Assy DCA220SSJ/SSJU Generator Assy DCA220SSJ/SSJU- Generator ASSY. DCA220SSJ/SSJU Generator ASSY. DCA220SSJ/SSJU Control Panel Assy DCA220SSJ/SSJU- Control Panel Assy DCA220SSJ/SSJU Control BOX Assy DCA220SSJ/SSJU Control BOX Assy DCA220SSJ/SSJU Control BOX ASSY. DCA220SSJ/SSJU Control BOX ASSY. DCA220SSJ/SSJU- Engine and Radiator Assy DCA220SSJ/SSJU Engine and Radiator Assy DCA220SSJ/SSJU Engine and Radiator Assy M4310300903 M431030120332A M4493601204 M4310301003DCA220SSJ/SSJU Engine and Radiator Assy 0802081003 06020210700269200660 M9300000203DCA220SSJ/SSJU Outputterminal Assy DCA220SSJ/SSJU Outputterminal Assy DCA220SSJ/SSJU Outputterminal ASSY. DCA220SSJ/SSJU Outputterminal ASSY. DCA220SSJ/SSJU Battery Assy DCA220SSJ/SSJU Battery Assy DCA220SSJ/SSJU Muffler Assy DCA220SSJ/SSJU Muffler Assy DCA220SSJ/SSJU Fueltank Assy DCA220SSJ/SSJU Fueltank Assy DCA220SSJ/SSJU Enclosure Assy DCA220SSJ/SSJU Enclosure Assy DCA220SSJ/SSJU Enclosure ASSY. DCA220SSJ/SSJU Enclosure ASSY. DCA220SSJ/SSJU Enclosure ASSY. DCA220SSJ/SSJU Enclosure ASSY. DCA220SSJ/SSJU Enclosure ASSY. M4453600004 M911300010262A 0030006000 M4453600104DCA220SSJ/SSJU Rubber Seals Assy DCA220SSJ/SSJU Rubber Seals Assy DCA220SSJ/SSJU Nameplate and Decals Assy DCA220SSJ/SSJU Nameplate and Decals Assy DCA220SSJ/SSJU Nameplate and Decals ASSY. DCA220SSJ/SSJU Nameplate and Decals ASSY. Terms and Conditions of Sale Parts Freight PolicyDCA-220SSJ/SSJU Operation and Parts Manual REV. #1 02/28/14 HERE’S HOW to GET Help

C1870300404, M4870300104B specifications

Multiquip, a leading manufacturer in the construction and industrial sectors, offers a wide range of durable and reliable products. Among its extensive portfolio, two notable models stand out: the M4870300104B and the C1870300404. These models are particularly praised for their efficiency, innovative technologies, and robust features that cater to various construction needs.

The Multiquip M4870300104B is a powerful multi-process welder, designed to tackle a wide variety of welding applications. This model is equipped with an advanced inverter technology that allows it to deliver smooth and stable arcs for TIG, MIG, and Stick welding. The inverter design also enhances energy efficiency, making it an ideal choice for both on-site and workshop use. Furthermore, the M4870300104B features a dual-voltage capability, supporting both 120V and 240V input, which provides flexibility for different job sites.

In terms of usability, the M4870300104B boasts an intuitive control panel that allows for easy adjustments. Its lightweight design ensures easy transport, while the rugged construction promises durability in demanding environments. With a duty cycle of 35% at 200 Amps, this welder is built for efficiency and long-lasting performance, making it suitable for both professional and DIY applications.

On the other hand, the C1870300404 is a high-performance concrete vibratory screed that plays a crucial role in ensuring smooth finishes on concrete surfaces. This model is engineered with advanced vibration technology which allows it to efficiently remove air pockets and stabilize the concrete. The C1870300404 features a robust aluminum frame, enhancing its durability while maintaining a lightweight structure for ease of handling.

Equipped with a powerful and reliable engine, the C1870300404 offers impressive runtime, allowing crews to work continuously without frequent interruptions. It also features adjustable vibration settings, enabling users to customize the intensity based on the specific requirements of the project at hand. The ergonomic design of the handle contributes to user comfort, reducing fatigue during extended periods of operation.

In conclusion, both the Multiquip M4870300104B and C1870300404 exemplify the brand’s commitment to quality, innovation, and user-centric design. These tools not only enhance productivity but also guarantee precision and efficiency in various construction tasks. Whether for welding or concrete finishing, Multiquip continues to deliver equipment that meets the evolving demands of the industry.