JVC RX-7022VSL manual Select the low frequency effect attenuator level, Crossover frequency

Page 21
T SETTING

Crossover frequency

Small speakers cannot reproduce the bass sounds efficiently. If you use a small speaker in any position, this receiver automatically reallocates the bass sound elements assigned from small speaker to large speakers.

To use this function properly, set this crossover frequency level according to the size of the small speaker connected.

•If you have selected “LARGE” for all speakers, this function will not take effect.

•Crossover frequency is not valid for the DVD MULTI playback mode and HEADPHONE mode.

2 Press CONTROL UP 5/DOWN ∞ to CONTROL

DOWN UP

select the low frequency effect attenuator level.

•Each time you press the button, the setting alternates between “0dB” and “–10dB.”

0dB : Normally select this.

–10dB : Select this when the bass sound is distorted.

1 Press SETTING repeatedly until

 

 

 

T

SETTING

 

 

“CROSS (Crossover)” (with the current

 

 

 

 

 

 

 

 

 

 

 

 

setting)* appears on the display.

 

 

 

 

 

 

 

 

 

SPK 1

 

 

 

 

DIGITAL AUTO L C R

 

 

 

 

LINEAR PCM S.WFR LFE

 

 

 

 

LS S RS

 

 

 

 

CH-

 

 

 

 

 

 

 

 

*“100HZ” is the initial setting. If you have already changed the setting, another frequency will be shown.

Dynamic range compression

You can compress the dynamic range (difference between maximum sound and minimum sound) of the reproduced sound. This is useful when enjoying surround sound at night.

•This function takes effect only when playing back a source encoded with Dolby Digital.

1 Press SETTING repeatedly until “D. COMP (Dynamic range compression)” (with the current setting)* appears on the display.

2Press CONTROL UP 5/DOWN ∞ to select the crossover frequency level you like to use.

•Each time you press the button, the crossover frequency level changes as follows:

80HZ 100HZ 120HZ

200HZ 150HZ

CONTROL

DOWN UP

 

SPK 1

 

DIGITAL AUTO

L

C

R

LINEAR PCM

S.WFR LFE

 

LS

S

RS

CH-

*“MID” is the initial setting. If you have already changed the setting, another setting will be shown.

2 Press CONTROL UP 5/DOWN ∞

DOWN UP

 

CONTROL

to select the appropriate compression

 

level.

 

Low frequency effect attenuator

If the bass sound is distorted while playing back software using Dolby Digital or DTS Digital Surround, follow the procedure below:

•Low frequency effect attenuator is not valid for DVD MULTI playback mode.

•This function takes effect only when the subwoofer (LFE) signals come in (with “SUBWOOFER” set to “YES”).

1 Press SETTING repeatedly until

 

 

 

T

SETTING

 

 

 

“LFE ATT (Low Frequency Effect

 

 

 

 

 

 

 

 

 

 

 

 

Attenuator)” (with the current

 

 

 

setting)* appears on the display.

 

 

 

 

 

 

 

 

 

 

 

SPK 1

 

 

 

 

DIGITAL AUTO

L C R

 

 

 

 

 

S.WFR LFE

 

 

 

 

DIGITAL

LS S RS

 

 

 

 

 

CH-

 

 

 

 

 

 

 

 

 

*“0dB” is the initial setting. If you have already changed the setting, “–10dB” will be shown.

•Each time you press the button, the display changes as follows:

OFF MID

MAX

OFF : Select this when you want to enjoy surround with its full dynamic range. (No effect applied.)

MID : Select this when you want to reduce the dynamic range a little.

MAX : Select this when you want to apply the compression effect fully. (Useful at night.)

18

Page 20 Page 22
Image 21
Page 20 Page 22
Contents RX-7022VSL Page RX-7022VSL Table of Contents Remote Control Parts IdentificationFront Panel Checking the Supplied Accessories Before Installation Putting Batteries in the Remote ControlGetting Started Replace the coverConnecting the FM and AM Antennas AM antenna connectionFM antenna connection Getting Started Connecting the SpeakersConnecting the rear and center speakers Connecting Audio/Video ComponentsConnecting the subwoofer speaker Analog connections Audio component connectionsCD player Video component connectionsCassette deck or CD recorder VCRTV and/or DBS tuner DVD player DVD playerDBS tuner B Plug the power cord into an AC outlet Connecting the Power CordDigital connections Digital output terminalTurning On the Power Basic OperationsSelecting the Source to Play Basic Operations Adjusting the VolumeTurning Off the Power With the Sleep Timer Listening Only with HeadphonesHeadphone mode Changing the Display BrightnessSignal and speaker indicators on the display Basic adjustment auto memorySignal indicators Speaker indicators Speaker indicators light up whenBasic Settings Setting the Digital InputDigital in Terminals Selecting the Analog or Digital Input Mode Basic SettingsSetting the Speaker Information Remote Selecting the Video InputTerminal Press Control UP 5/DOWN ∞ to select the unit Unit with the current setting Appears on the displaySelect the appropriate speaker distance Speaker sizeTo select the appropriate compression Level Select the low frequency effect attenuator levelCrossover frequency Dynamic range compressionSound Adjustments Adjusting the Front SpeakersOutput Balance Adjusting the Tone Adjusting the Subwoofer Output LevelReinforcing the Bass Tuning in Stations Manually Using Preset TuningTuner Operations Selecting the FM Reception Mode Dolby Surround Creating Realistic Sound FieldsDTS Digital Surround Typical Multichannel 5.1 ch reproductionDAP Digital Acoustic Processor modes DVD Multi Playback ModeCreating sound field All Channel StereoAbout Relations between Speaker Layouts and Surround Modes Creating Realistic Sound FieldsTurning on or off the Surround modes Selecting the Surround modesActivate Surround mode If you like to adjust sound, go to stepPress Surround ON/OFF to Press Test to check if you can hear Adjust the speaker output levels -10 to +10Equal level Press Test again to stop the testUsing DAP Modes and All Channel Stereo Press Surround Mode repeatedly Surround Mode Press Surround ON/OFF to activate Surround modeEffect with the current Setting* appears on the display PAVILION-or ALL CH Stereo appears on the displayActivating DVD Multi Playback Mode Using DVD Multi Playback ModePress DVD Multi Following indications appears On the displayPress the play 3 button on the CD player Compu Link Remote Control SystemAutomatic Source Selection Synchronized RecordingConnections 1 AV Compu Link Connection AV Compu Link Remote Control SystemConnections 2 Video Cable Connections CaseAutomatic Selection of TV’s Input Mode AV Compu Link Remote Control SystemAutomatic Power On/Off One-Touch Video PlayEx. When you press CD Sound AdjustmentOperating JVC’s Audio/Video Components Operating Audio ComponentsOperating JVC’s Audio/Video Components Operating Video Components DVD playerDVD menu operations If there are more than one code listed for your brand of TV To change the transmittable signals for operating a TVOperating Other Manufacturers’ Video Equipment Try to operate your TV by pressing TVIf there are more than one code listed for your brand To change the transmittable signals for operating a VCRTry to operate your VCR by pressing Manufacturers’ codes for Catv converter CodesTry to operate your DVD player by pressing Operating Other Manufacturers’ Video EquipmentManufacturers’ codes for VCR Codes Manufacturers’ codes for DVD player CodesProblem Possible Cause Solution TroubleshootingAmplifier SpecificationsFM tuner IHF AM tunerGeneral 0402NHMMDWJEIN

RX-7022VSL specifications

The JVC RX-7022VSL is a versatile and powerful receiver designed to enhance the audio experience in your home entertainment system. This model combines advanced technologies and user-friendly features, making it a popular choice among audio enthusiasts.

One of the standout features of the RX-7022VSL is its robust power output. The receiver provides 100 watts per channel, delivering a clear and dynamic sound across various audio formats. This power output is particularly beneficial for driving larger speakers, ensuring that even the most demanding audio tracks are rendered with precision and clarity.

The RX-7022VSL is equipped with multiple audio inputs, including HDMI, coaxial, and optical connections. This extensive range of inputs allows easy connectivity with various source devices, such as Blu-ray players, gaming consoles, and streaming devices. The receiver also supports multiple audio formats, including Dolby Digital, DTS, and PCM, ensuring optimal compatibility with your existing audio equipment.

One of the key technologies featured in the RX-7022VSL is JVC’s proprietary Digital Signal Processing (DSP). This technology enhances the sound quality by providing advanced audio filtering and sound field options, allowing you to tailor the listening experience to your preferences. The receiver also includes a built-in equalizer, enabling users to adjust the sound profile to suit their audio tastes and room acoustics.

In addition to its audio capabilities, the RX-7022VSL includes a user-friendly remote control, allowing for easy adjustment of settings from across the room. The on-screen display simplifies navigation through various audio modes and settings, making it accessible for users of all skill levels.

The design of the RX-7022VSL is both sleek and functional, with a modern aesthetic that fits well in any home theater setup. The front panel features a clear LED display, rotary knobs for volume and input selection, and dedicated buttons for quick access to commonly used features.

In summary, the JVC RX-7022VSL receiver stands out for its powerful audio performance, versatile connectivity options, and user-friendly interface. With its combination of cutting-edge technology and thoughtful design, it is well-suited for both casual listeners and audiophiles seeking to elevate their home sound experience. Whether you're watching movies, listening to music, or enjoying gaming, the RX-7022VSL delivers a captivating audio experience that enhances any entertainment setup.
Top Page Image Contents