JVC RX-7022VSL manual Compu Link Remote Control System, Press the play 3 button on the CD player

Page 34

COMPU LINK Remote Control System

The COMPU LINK remote control system allows you to operate JVC’s audio components through the remote sensor on the receiver. To use this remote control system, you need to connect JVC’s audio components through the COMPU LINK-4 (SYNCHRO) jacks (see below) in addition to the connections using cables with RCA pin plugs (see pages 6 and 7).

•Make sure that the AC power cords of these components are unplugged before connection. Plug the AC power cords only after all connections are completed.

Automatic Power On/Off (Standby): only possible with the COMPU LINK-3 and COMPU LINK-4

Both the CD player and cassette deck (or CD recorder) turn on and off (standby) along with the receiver.

When you turn on the receiver, the CD player or cassette deck (or CD recorder) will turn on automatically, depending on which component has been previously selected.

When you turn off the receiver, both the CD player and cassette deck (or CD recorder) will turn off (standby).

CD player

Cassette deck

or

CD recorder

COMPU LINK-4

(SYNCHRO)

Turntable

Notes:

•There are four versions of COMPU LINK remote control system. This receiver is equipped with the fourth version—COMPU LINK-4. This version is added systematic operations with the CD recorder to the previous version—COMPU LINK-3.

•If your audio component has two COMPU LINK jacks, you can use either one. If it has only one COMPU LINK jack, connect it so that it is the last item in the series of components.

•To operate the cassette deck or CD recorder using the COMPU LINK remote control system, set the source name correctly. (See page 11.)

•Refer also to the manuals supplied with your audio components.

This remote control system allows you to use four functions listed below.

Remote Control through the Remote Sensor on the Receiver

You can control the connected audio components through the remote sensor on the receiver using this remote control. Aim the remote control directly at the remote sensor on the receiver. For details, see pages 34 and 35.

Automatic Source Selection

When you press the play (3) button on a connected component or on its own remote control, the receiver automatically turns on and changes the source to the component. On the other hand, if you select a new source on the receiver or on the remote control, the selected component begins playing immediately.

In both cases, the previously selected source continues playing without sound for a few seconds.

Synchronized Recording

Synchronized recording means the cassette deck starts recording as soon as a CD begins playing.

To use synchronized recording, follow these steps:

1Put a tape in the cassette deck and a disc in the CD player.

2Press the record () button and the pause (8)

button on the cassette deck at the same time.

This puts the cassette deck into recording pause.

If you do not press the record () button and pause (8) button at the same time, the synchronized recording feature will not operate.

3Press the play (3) button on the CD player.

The source changes on the receiver, and as soon as play starts, the cassette deck starts recording. When the play ends, the cassette deck enters recording pause, and stops about 4 seconds later.

Notes:

•During synchronized recording, the selected source cannot be changed.

•If the power of any component is shut off during synchronized recording, the COMPU LINK remote control system may not operate properly. In this case, you must start again from the beginning.

31

Page 33 Page 35
Image 34
Page 33 Page 35
Contents RX-7022VSL Page RX-7022VSL Table of Contents Parts Identification Remote ControlFront Panel Getting Started Before Installation Putting Batteries in the Remote ControlChecking the Supplied Accessories Replace the coverAM antenna connection Connecting the FM and AM AntennasFM antenna connection Connecting the Speakers Getting StartedConnecting the subwoofer speaker Connecting Audio/Video ComponentsConnecting the rear and center speakers Analog connections Audio component connectionsCassette deck or CD recorder Video component connectionsCD player VCRDVD player TV and/or DBS tuner DVD playerDBS tuner B Digital connections Connecting the Power CordPlug the power cord into an AC outlet Digital output terminalBasic Operations Turning On the PowerSelecting the Source to Play Adjusting the Volume Basic OperationsHeadphone mode Listening Only with HeadphonesTurning Off the Power With the Sleep Timer Changing the Display BrightnessSignal indicators Speaker indicators Basic adjustment auto memorySignal and speaker indicators on the display Speaker indicators light up whenSetting the Digital Input Basic SettingsDigital in Terminals Basic Settings Selecting the Analog or Digital Input ModeSelecting the Video Input Setting the Speaker Information RemoteTerminal Select the appropriate speaker distance Unit with the current setting Appears on the displayPress Control UP 5/DOWN ∞ to select the unit Speaker sizeCrossover frequency Select the low frequency effect attenuator levelTo select the appropriate compression Level Dynamic range compressionAdjusting the Front Speakers Sound AdjustmentsOutput Balance Adjusting the Subwoofer Output Level Adjusting the ToneReinforcing the Bass Using Preset Tuning Tuning in Stations ManuallyTuner Operations Selecting the FM Reception Mode DTS Digital Surround Creating Realistic Sound FieldsDolby Surround Typical Multichannel 5.1 ch reproductionCreating sound field DVD Multi Playback ModeDAP Digital Acoustic Processor modes All Channel StereoTurning on or off the Surround modes Creating Realistic Sound FieldsAbout Relations between Speaker Layouts and Surround Modes Selecting the Surround modesIf you like to adjust sound, go to step Activate Surround modePress Surround ON/OFF to Equal level Adjust the speaker output levels -10 to +10Press Test to check if you can hear Press Test again to stop the testUsing DAP Modes and All Channel Stereo Effect with the current Setting* appears on the display Press Surround ON/OFF to activate Surround modePress Surround Mode repeatedly Surround Mode PAVILION-or ALL CH Stereo appears on the displayPress DVD Multi Using DVD Multi Playback ModeActivating DVD Multi Playback Mode Following indications appears On the displayAutomatic Source Selection Compu Link Remote Control SystemPress the play 3 button on the CD player Synchronized RecordingConnections 2 Video Cable Connections AV Compu Link Remote Control SystemConnections 1 AV Compu Link Connection CaseAutomatic Power On/Off AV Compu Link Remote Control SystemAutomatic Selection of TV’s Input Mode One-Touch Video PlayOperating JVC’s Audio/Video Components Sound AdjustmentEx. When you press CD Operating Audio ComponentsOperating JVC’s Audio/Video Components DVD player Operating Video ComponentsDVD menu operations Operating Other Manufacturers’ Video Equipment To change the transmittable signals for operating a TVIf there are more than one code listed for your brand of TV Try to operate your TV by pressing TVTry to operate your VCR by pressing To change the transmittable signals for operating a VCRIf there are more than one code listed for your brand Manufacturers’ codes for Catv converter CodesManufacturers’ codes for VCR Codes Operating Other Manufacturers’ Video EquipmentTry to operate your DVD player by pressing Manufacturers’ codes for DVD player CodesTroubleshooting Problem Possible Cause SolutionSpecifications AmplifierAM tuner FM tuner IHFGeneral 0402NHMMDWJEIN

RX-7022VSL specifications

The JVC RX-7022VSL is a versatile and powerful receiver designed to enhance the audio experience in your home entertainment system. This model combines advanced technologies and user-friendly features, making it a popular choice among audio enthusiasts.

One of the standout features of the RX-7022VSL is its robust power output. The receiver provides 100 watts per channel, delivering a clear and dynamic sound across various audio formats. This power output is particularly beneficial for driving larger speakers, ensuring that even the most demanding audio tracks are rendered with precision and clarity.

The RX-7022VSL is equipped with multiple audio inputs, including HDMI, coaxial, and optical connections. This extensive range of inputs allows easy connectivity with various source devices, such as Blu-ray players, gaming consoles, and streaming devices. The receiver also supports multiple audio formats, including Dolby Digital, DTS, and PCM, ensuring optimal compatibility with your existing audio equipment.

One of the key technologies featured in the RX-7022VSL is JVC’s proprietary Digital Signal Processing (DSP). This technology enhances the sound quality by providing advanced audio filtering and sound field options, allowing you to tailor the listening experience to your preferences. The receiver also includes a built-in equalizer, enabling users to adjust the sound profile to suit their audio tastes and room acoustics.

In addition to its audio capabilities, the RX-7022VSL includes a user-friendly remote control, allowing for easy adjustment of settings from across the room. The on-screen display simplifies navigation through various audio modes and settings, making it accessible for users of all skill levels.

The design of the RX-7022VSL is both sleek and functional, with a modern aesthetic that fits well in any home theater setup. The front panel features a clear LED display, rotary knobs for volume and input selection, and dedicated buttons for quick access to commonly used features.

In summary, the JVC RX-7022VSL receiver stands out for its powerful audio performance, versatile connectivity options, and user-friendly interface. With its combination of cutting-edge technology and thoughtful design, it is well-suited for both casual listeners and audiophiles seeking to elevate their home sound experience. Whether you're watching movies, listening to music, or enjoying gaming, the RX-7022VSL delivers a captivating audio experience that enhances any entertainment setup.
Top Page Image Contents